錘擊數 的英文怎麼說

中文拼音 [chuíjīshǔ]
錘擊數 英文
blow count
  • 錘 : Ⅰ名詞1 （一種古代兵器） a metal ball with a handle or chain used as weapon; mace2 （秤坨; 像錘的...
  • 數 : 數副詞（屢次） frequently; repeatedly
  1. Abstract : to counter the ore - rock with different characteristics, the theory of wave mechanics on impacting machinery was used in combination with the results of digital emulation study of hydraulic hammer machine to obtain the output impact energy of hydraulic hammer apparatus and the power of the main engine of hydraulic hammer machine, thus providing the basis for proper selection of the hammerhead and chassis of hydraulic hammer machine

    文摘:針對不同特性的礦巖，運用沖擊機械波動力學理論，並結合液壓碎石器的數字模擬研究結果，得出液壓碎石器的輸出沖擊能與液壓碎石機的主機功率，從而為合理選用液壓碎石機錘頭及底盤提供了參考依據。
  2. To counter the ore - rock with different characteristics, the theory of wave mechanics on impacting machinery was used in combination with the results of digital emulation study of hydraulic hammer machine to obtain the output impact energy of hydraulic hammer apparatus and the power of the main engine of hydraulic hammer machine, thus providing the basis for proper selection of the hammerhead and chassis of hydraulic hammer machine

    針對不同特性的礦巖，運用沖擊機械波動力學理論，並結合液壓碎石器的數字模擬研究結果，得出液壓碎石器的輸出沖擊能與液壓碎石機的主機功率，從而為合理選用液壓碎石機錘頭及底盤提供了參考依據。
  3. Exciting method is used to measure the damping, the four damping coefficients of the radial part and a damping coefficient of the thrust part can be obtained though hammering the testing bearing which is in a equilibrium position. based on the testing data, the dynamic characteristic curves of the radial - thrust floating ring hybrid bearing are drawn and compared with the theoretical curves

    採用激振法測量軸承的阻尼，對處于平衡位置的測試軸承分別沿水平方向、上45度方向及軸向進行錘擊，根據錘擊法原理求得各個轉速下軸承徑向部分內、外膜總阻尼系數以及推力部分內、外膜總阻尼系數。
  4. By using the model analysis method and hammer test, the model parameters and model shapes are obtained based on the force and response signal processing

    本文利用試驗模態分析技術，通過沖擊錘激振試驗，對激振力信號和響應信號處理的基礎上，獲得機床結構的模態參數和振動模型。
  5. By using the data of the experiment, this dissertation has analysed the relationship between the dynamic parameter and the self - property, then based on the elastic half space theory of the dynamic foundation, this dissertation get the method to measure the density of silt or sand subsoil using instantaneous implusion

    本文通過試驗獲得的數據，分析地基土的動力參數與土體的本身性質之間的關系，並應用動力基礎半空間理論，得到了全新的利用瞬態錘擊法來測定粉砂土的密實度的方法。
  6. The outputs of tests on the thin plate under different inputs have been investigated for testifying the system. different solutions have been compared according to the frequency - spectrum characters and structure modal parameters. it is indicated that the solutions in this paper are consistent with the solution of the fea methods

    以薄鋼板為實例，探討了不同激勵條件下，包括正弦穩態激勵、正弦慢掃描、單次錘擊和隨機錘擊激勵，薄鋼板振動系統的響應情況，以頻譜特性和模態參數為參考，將各種方法的求解結果作了比較，結果表明：本系統得出的結果與有限元解具有一致性。
  7. The deep impact flyby spacecraft carries two cameras and an infrared device to analyze spectral data, while the impactor carried a camera that sent back dramatic images of the comet until three seconds before the collision

    深沖擊飛行由航天器運載二臺照相機和一個紅外設備分析數據，當"錘碎機"運載了退還彗星的劇烈的圖象直到三秒在碰撞之前的一臺照相機。
  8. Then model experimental on the steel frame structure, experiment uses random knock and single knock separately on the steel frame structure through a force hammer. we can gained the data of experiment using transducers and the data acquisition system and post treatment of the data

    然後，對該鋼框架模型進行模態試驗，試驗通過力錘分別對鋼框架進行隨機敲擊和單次敲擊，通過傳感器和數據採集系統得到結構的試驗數據，再對試驗數據進行后處理。
  9. Abstract : through contrasting of the results of different geotecnical investigation methods in several engineering project the effective methods to determine ground standard value of bearing capacity by standard penetration is presented

    文摘:通過對實際工程不同勘探方法對比研究，提出了用標貫試驗錘擊數確定粘性土地基承載力標準值的有效方法。
  10. The structure and the process of the sensors are designed according to the preferences. the samplers of the sensors are produced successfully. the samplers are demarcated dynamic, and the results turn up trumps

    在參數選擇基礎上，設計了傳感器的結構和工藝路線，並經過幾個批次的試制，成功地加工出了傳感器樣機，利用馬希特擊錘對傳感器樣機進行了動態標定，標定結果令人滿意。
  11. Moreover, when the filaments are treated for 12 minutes, the interfacial shear stress will be lower than that treated for 6 minutes. izod pendulum is used to test the influence of the fiber / matrix bond strength on the low velocity impact responses of the composites. the curves of energy - time, force - time and velocity - time are obtained by a data acquisition system

    用擺錘低速沖擊儀對界面粘結強度不同的材料進行沖擊試驗，藉助數據採集系統得到沖擊過程中材料吸收的總能量、承受載荷、擺錘速度等參數與時間的關系曲線，並通過pc機處理，將載荷?時間曲線轉化為載荷?位移曲線。
  12. Counter blow hammer. types and basic parameter

    對擊錘.型式與基本參數
分享友人
分享到 Line

分享到臉書