鍋爐的結構 的英文怎麼說

中文拼音 [guōlúdejiēgòu]
鍋爐的結構 英文
configure of oilfired boiler andd
  • 鍋 : 名詞1. （炊事用具） pan; pot 2. （裝液體加熱用的器具） boiler; cauldron3. （某些器物上像鍋的部分） bowl （of a pipe, etc. ）
  • 的 : 4次方是 The fourth power of 2 is direction
  • 結 : 結動詞（長出果實或種子） bear （fruit）; form （seed）
  • 構 : Ⅰ動詞1 （構造; 組合） construct; form; compose 2 （結成） fabricate; make up 3 （建造; 架屋） bui...
  • 鍋爐 : boiler; furnace
  • 結構 : 1 （各組成部分的搭配形式） structure; composition; construction; formation; constitution; fabric;...
  1. The experimentation of cool and hot diagnosis reflected the structure and disposal of combustor, slag bonding and smirch of hearth are the main factors of hearth ' s outlet overheat and output of boiler decline

    冷、熱態診斷試驗反映出爐膛結焦、粘污及燃燒器的結構和布置等因素是造成爐膛出口煙溫偏高，鍋爐出力下降的主要因素。
  2. This article aims at the boiler ' s problems in operation : 1 ) under nominal load, the smoke temperature at the outlet of hearth reaches 1200, far more exceeds 1050 the original designed temperature. this will always result in slag inside boiler and the temperature of overheater ' s pipe superheat, so that boiler cannot take nominal load and all these influence boiler ' s nomal operation heavily, 2 ) this article also studied the reason why the assistant oil becoming necessary when coal changes. during the nomal operation, many factors ( makeup of combustor and its disposal, smirch and encrust of water wall, excessive air coefficient, temperature of primary air, coal type and density of coal dust ) can deviate the designed working conditions, then affect the boiler ' s nomal operation

    本文針對該鍋爐在實際運行中存在的問題：在額定負荷下，爐膛出口超溫、低溫段過熱器前煙溫高達936 ，遠遠超過815的設計值；噴燃器四周水冷壁結焦嚴重，過熱器管壁溫度超標，無法帶上額定負荷；甚至有時因燃煤質量的變化，必須投油助燃的嚴重情況進行了分析研究。在實際生產過程中，燃燒器的結構、布置，水冷壁的粘污、結垢，過剩空氣系數、一次風溫、煤種及其濃度變化等許多因素都會偏離鍋爐的設計工況，從而影響爐內的傳熱和燃燒，造成爐膛出口超溫、水冷壁結渣等問題。
  3. The research state, significance, and applications about boiler steel frame are introduced, including its merits and demerits

    介紹了鋼結構的發展現狀、及其研究的意義，以及鍋爐鋼結構國內外應用背景，分析了鋼結構的優缺點。
  4. The effect factors of boiler steel frame are analyzed, loads composition and structural distribution, also the design code and special value norm for load classification are discussed, mainly including state and live loads, wind and level earthquake

    分析了電站鍋爐鋼結構的荷載影響因素，提出合理的結構布置和荷載取值及其工況組合。分析了設計標準中的荷載分類及取值約定。
  5. Considering special form of the boiler frame, the reconstruction and enforcement method, in addition dynamic analysis are given by particular steps : establishment of the model of boiler steel frame, determination of earthquake loads and distribution form, and anti - side force system for the frame to model and analyze, involving loads on the frame and above it, earthquake loads, damping, sway control installation, hanging bar and plate beam

    考慮鍋爐構架鋼結構的特殊形式，研究並提出了電站鍋爐鋼結構改造加固研究方法，及動力分析的具體步驟：建立了鍋爐鋼結構動力分析模型、地震荷載分析方法、建立了鍋爐鋼結構布置型式、及整個鍋爐鋼構架抗側力體系模擬分析方法。具體包括：鋼構架本體及構架上荷載、地震載荷與阻尼系數確定、制晃裝置確定、吊桿與大板梁簡化。
  6. 3. on boiler retrofit, the calculation of fuel burning, the heat calculation of boiler inside structure and convection section, and the design of structure parameter of feed water heat exchanger are made. the flue gas channels " resistance calculation and the boiler strength verifying are also carried out. replacement of water cooling wall improves heat exchanging and decreases loss of heat radiant

    對鍋爐本體進行了燃料燃燒計算、爐膛結構熱力計算、對流受熱面結構熱力計算、鍋爐給水加熱器結構參數設計、煙道阻力計算及鍋爐元件強度校核等；改進了水冷壁布置使換熱效果更好，減少輻射換熱損失；改進對流段結構，更充分的利用爐膛出口煙氣余熱，提高熱效率；並且進行了煙氣阻力計算、熱效率計算和能量平衡測試，對改進后的稠油燃料和改進前進行了對比，燃燒狀況和熱效率有明顯改善。
  7. The reform scheme of no. 1 boiler in fengtai company is confirmed on the basis of cold / hot tests, theoretical discussions and calculations. in the process of field retrofit, it is indicated in the operation of the improved furnace that without the change of furnace structure, the transform of the burner angle has shrunk the tangential diameter and prevented flames burning on furnace walls, and the burning state of furnace has been bettered, simultaneously, lowering the slagging wi in furnace, thus laying sol id foundation for the safe and economic operation of generating units. wuyanrong ( power plant thermal power engineering ) directed by prof

    本論文通過冷、熱態試驗，經過論證和計算，確定了豐泰公司~ # 1爐燃燒器的改造方案，並進行了現場改造，改造后實際運行狀況表明：在無法改變爐膛結構的情況下，改變燃燒器角度，縮小切圓直徑，使火焰不貼壁，改善了爐內燃燒工況，同時降低了鍋爐結渣的程度，為機組的安全經濟運行奠定了必要的技術基礎。
  8. On one hand one can inquire more comprehensive conditions of steel construction, industrial plant construction or of industrial boilers or on the other hand of refuse incineration plants, waste incineration plants, waste heat boilers in addition to bridge sanitation and steam boilers and steam generators, under the number + 49 203 44 98 - 314 at thyssen kloenne gmbh

    Thyssen kloenne gmbh是一家高級企業，該企業針對客戶需求製造專門的廢熱鍋爐、余熱鍋爐，橋梁整修，蒸氣鍋爐和蒸氣機，垃圾焚燒設備，工業設備製造，工業鍋爐，鋼結構。
  9. This paper introduce the features of a kind of electric heating atmospheric boiler which is of high efficiency on energy transferring, non - pollution, starting and stopping quickly, wider range of load adjusting, simple body structure, etc. in addition the paper introduce the design idea briefly

    電加熱鍋爐具有能量轉化效率高、零污染、起停速度快、負荷調節范圍大、本體結構簡單等特點，文章具體介紹了一種常壓熱水電鍋爐的設計。
  10. This program can predict the wall temperature 、 internal wall heat tranfer coefficient 、 fluid temperature and entropy profile along the water wall. all of these provide an important foundation for designing this type of water wall structure to ensure the safety of the boiler operation. this hydrodynamic calculation program and the results can be used to analyze operation reliability and structure design of water wall system

    利用所開發的程序對設計的超臨界cfb進行了計算，給出不同負荷下，水冷壁出口工質溫度分佈，水冷壁受熱面不同位置處的金屬壁溫、內壁放熱系數、流體溫度焓值分佈，以及不同管子的流動壓降等結果，為分析鍋爐工作可靠性及水冷壁系統的結構設計提供了重要依據。
  11. The stress of slag rests with the structure, physical characteristic, and heat transfer status of slag. taking no. 1 boiler of beilun thermal power plant as example, the walltube thermal stress and the destroying impact on slag are researched

    得出鍋爐大范圍變負荷運行時熱應力能夠超過渣的強度極限引起渣結構破壞的結論，渣層的熱應力主要取決于渣的結構、物理特性和傳熱狀態。
  12. From the view point of system flowage of coal in power generation enterprises, this paper reviews the effect of coal characteristics on the operation of power plants boiler, and proposes modeled means and methods which expresses the coal characteristics affecting generation cost. the modeling of coal characteristic effects helps power generation and coal enterprises to provide and produce more economic coal for power plants, the function and characteristic of coal quality engineering analysis for power plant is discussed, the structure of coal quality engineering analysis system is explained combining with the electric produce process

    從發電企業煤的系統流程出發，研究了燃煤特性對電站鍋爐運行的影響，提出了煤質特性對發電成本影響模型化的途徑和方法。煤質影響模型的建立有利於發電企業和煤炭企業採取措施，組織和生產對于電站來說更為經濟的煤源。討論了火電廠煤質工程分析方法的功能及特點，並結合火電廠電力生產過程和煤質工程分析關系圖說明了煤質工程分析系統的結構。
  13. First, the working principles of the combustion control system of marine main boiler in present use and its disadvantages are discussed in the paper ; in the light of the structure and motion traits of marine main boiler, the combustion control systems of single and double cross amplitude limits are designed. at the same time, the schematic diagram of system and recovery curves of some relative parameters are given, the system working principles and its advantages and disadvantages are discussed. based on the combustion control system of dual - crisscross amplitude limit, by selecting the independent variable, the fixed offset is improved into variable offset, the combustion control system of variable offset dual - crisscross amplitude limit is designed

    首先討論了目前船用主鍋爐燃燒控制系統的工作原理及存在的不足；針對船用主鍋爐的結構及運行特點，設計了單交叉限幅燃燒控制系統和雙交叉限幅燃燒控制系統，同時給出了系統原理圖及有關參數的過渡過程曲線，討論了系統工作原理及優缺點；在雙交叉限幅燃燒控制系統的基礎上，將固定偏置經過自變量的選取，改進成變偏置，設計了變偏置雙交叉限幅燃燒控制系統，給出了系統原理圖及有關參數的過渡過程曲線，同時也給出了空氣壓力和燃油流量正負偏置函數與變偏置折線函數的關系式。
  14. In this paper, the control system of industrial boiler widely used in industrial production was studied. aiming at the nonlinear object of industrial boiler with instability parameter and difficult building math model, combining fuzzy control theory and neural networks theory, a adaptive controller built with compensatory fuzzy neural networks to control industrial boiler is proposed

    本文對于目前在工業生產中廣泛應用的工業鍋爐的控制系統進行了研究，針對工業鍋爐這種具有非線性、參數不穩定、難以建立精確的數學模型的控制對象，結合模糊控制理論和人工神經元網路理論，提出用補償模糊神經網路構造自適應控制器實現對工業鍋爐的過程式控制制。
  15. The original design was intermediate vapor 42t / h, but the actual output is 30 - 35t / h, at the same time the temperature and pressure of the vapor are unstable, it affects the economic efficiency, the reason were the collecting dust on the heat area and serious corrision, they led to the decrease of the boiler load, and need stop to washing the dust, the article deals with the reform of the exhaust gas boiler, at the basic of the design condition, after thermo calculation, flute gas, resistence calculationand strenth calculation, the structure of the heat surface had been rearranged, then the proof calculation was done

    原設計產中壓蒸汽42噸時，但投運后只產30 - 35噸時，並且蒸汽溫度和壓力均不穩定，影響到經濟效益。其原因是受熱面積灰和腐蝕嚴重，影響傳熱使鍋爐負荷下降，不能長時間運行，需停產清理積灰。本論文針對此余熱鍋爐的技術改造，在給定設計條件基礎上，通過熱力計算，煙氣阻力計算和強度計算，對鍋爐受熱面結構重新布置，然後再作校核計算。
  16. Aiming at the structure characteristics of the pipeline system of the existing boiler combustion equipment, the paper work out the new - style air speed measure components via the theory analysis of the existing measure components of all kind of forms and measure theory. and then the paper designs and builds the wind tunnel test - bed to process the test and research of the air speed measure components in order to realize it ' s structure and each characteristic parameter

    針對現有的鍋爐燃燒設備管路系統的結構特點，論文通過對現有的各種形式、測量原理的流量測量裝置的理論分析，設計出新型的風速測量元件，並且設計、建立滿足試驗所需的風洞試驗臺，對風速測量元件的結構及各項特性指標進行試驗研究，完成一次元件的開發工作。
  17. Control and adjustment of the key running parameter of cfb boiler

    循環流化床鍋爐方便維檢的結構性設置研究
  18. By introduction to structure analysis and design calculation of middle pressure tubular waste heat boiler with expansion joint, the author thinks rational selection to the standard and code of the boiler and vessel is the key to assure the product design and manufacture quality and guarantee personal safety without the special national standard " tubular waste heat boiler " now

    摘要通過介紹一臺6t / h 、帶膨脹節的中壓管殼式余熱鍋爐的結構分析和設計計算過程，認為在目前國內尚沒有專門的《管殼式余熱鍋爐》標準情況下，合理選用各受壓元件所對應的鍋爐、壓力容器標準規范，是確保該類產品設計製造質量和保障人身安全的關鍵。
  19. Construction features and key technology of large - sized high - parameter d - type boilers

    型鍋爐的結構特點和關鍵技術
  20. In this dissertation, the structure character of the marine boiler was introduced, the dynamic characteristic of it was analyzed, and a dynamic mathematical model of the boiler steam - water system was established. based on this model, a simulation model was obtained, and it was used to simulate the working process of the marine boiler

    本文介紹了船用鍋爐的結構、特點，根據其工作過程及運行工況，分析了船用鍋爐所特有的動態性能，在此基礎上建立了船用鍋爐汽水系統的動態數學模型，並將此模型轉化為模擬模型對其進行了模擬研究。
分享友人
分享到 Line

分享到臉書