鍍膜計 的英文怎麼說

中文拼音 [dùmójì]
鍍膜計 英文
film plating machine
  • 鍍 : 動詞（用電解或其他化學方法使一種金屬附著到別的金屬或物體表面上） plate
  • 膜 : 名詞1. [生物學] （像薄皮的組織） membrane 2. （像膜的薄皮） film; thin coating
  • 計 : Ⅰ動詞1 （計算） count; compute; calculate; number 2 （設想; 打算） plan; plot Ⅱ名詞1 （測量或計算...
  1. According to the requirements of the cng on neutron flux, critical wavelength and distance between inpile guides and the cns, the relation between the source size and the critical angle of the coating material of the inpile guides as well as neutron flux at exit of the cngs have been studied

    根據導管設計指標的需要，研究了冷源尺寸與堆內導管內壁鍍膜材料的全反射臨界角和導管系統出口處中子注量率的關系。
  2. The results of design explain that if sio2 films deposited on the surfaces of sapphire the average transmittance in 3 ~ 5 m waveband can exceed 97 %, which can meet the requirements of missile dome in infrared application

    設計結果表明，藍寶石襯底雙面鍍sio _ 2 、 sio _ 2 / si等膜系，在3 5 m波段的平均透過率大於97 ，可滿足導彈頭罩設計和使用的要求。
  3. The light guiding unit on the surface is composed of sub - micron gratings whose transmission wavelengths are red, green and blue in order. the light source are red 、 green 、 blue led or semiconductor laser array. to enhance the light utilization, the surfaces of light guide plate except the incident and transmitted surfaces are coated with metallic film

    本文設計的亞微米光柵型導光板為矩形狀的，導光板上表面的導光單元是由三套出射光主波長分別是紅光632 . 8nm ，綠光521nm ，藍光441 . 6nm的亞微米光柵組成，光源採用的是紅、綠、藍三色發光二級管或者半導體激光器陣列，為了提高光能利用率，除入光面和出光面外，導光板其餘面都鍍上金屬膜。
  4. The quartenvave film stack based on one dimensional photonic crystal technology is designed. the measurement of the ir band is relatively mutual while that of mmw band is lack of report. the reflectivity of ir area ( 3 - 5 m ) by fourier transform infrared spectrometer ( ft - ir ) is given, and the experimental data of mmw band in microwave network analysis is also given

    本文給出了直接在傅立葉紅外光譜儀中進行的紅外波段透射率（實際是反射率）測量結果，在毫米波波段，通過自行設計的測試方法與測試系統，給出了在hp8510矢量網路分析儀下測得的未鍍膜、鍍膜樣品的比對測試結果。
  5. The enhanced photoconductive effect from small amount of tnf facilitates the preparations of new organic photoconductive devices under the drive of low fields. in the fourth chapter, inclpc nanoparticles embedded in poly ( n - vinylcarbzaole ) ( pvk ) were prepared successfully by dissolving inclpc in aprotic organic solvent / lewis acid with great concentration for the formation of electron donor - acceptor complexes, i. e., the method of complexation - mediated solubilization. the fabricated inclpc nanoparticles were characterized by means of uv / vis absorption, x - ray diffraction pattern, and tem

    論文的最後一章中，我們合成了具有較好的電子傳輸性能的化合物』一二苯基四竣酸花酚亞胺（ ddp ） ；研究了其溶解性、熱穩定性、晶體結構、紅外光譜、紫外吸收光譜和蒸鍍薄膜的屬性，並用量子化學計算方法模擬其單分子的空間構型；載流子遷移率測試的結果約為ix10 「 、 m 』 v 」 』 ? s 「 』 。
  6. Our factory specializes in manufacturing cabinet vacuum coaters, magnetic control sputter coaters and vacuum exhaust equipments, industrial boiler, all kinds of valves, coaters and press packer specially used in the industry of quartz crystal

    我廠是國內專業生產箱式真空鍍膜機、磁控濺射鍍膜機、真空排氣設備、石英晶體行業專用被銀機和壓封機、工業爐及各種真空閥門設計製造的專業廠家。
  7. The analytical expressions of reflectance and penetration depth of a light beam transmitted in the back - side - coated chirped mirror are obtained through couple - mode equations with boundary conditions

    摘要應用耦合模方程對光波在後端鍍膜啁啾反射鏡中的傳播規律進行分析計算，在分析的過程中加入了邊界條件的影響，推導出後端鍍膜啁啾反射鏡在理想情況下的反射率和穿透深度的解析表達式。
  8. In this paper, the property difference of sio2 sols used for preparing thin films by esam method or sol - gel process has been discussed. three kinds of sio2 sols were prepared, catalyzed by hcl or nh3 h2o only, or hcl first and then nh3 h2o respectively ( please note : in following text, the sio2 sol catalyzed by hc1 first and then nh3 h2o and its correspondent films will be named sio2 sol 1 # and film 1 ; the sio2 sol catalyzed by nh3 h2o only and its correspondent films will be named sio2 sol 2 # and film 2 # ). through investigating the assembling properties of the sols, observing thin films " microscopic structure with tem and testing their transmissivity with 721 spectrophotometer, we find that the first kind of sol is not suitable for preparing esam films, but the last two, i. e. sol 1 # and sol 2 #, are good

    本文討論了esam法制備薄膜所用的溶膠與sol - gel法所用的溶膠在性能上的區別，在hc1或nh _ ? h _ 2o分別單獨催化和hc1 nh _ 3 ? h _ 2o分步催化三種催化條件下制備了sio _ 2溶膠（以下規定hc1 nh _ 3 ? h _ 2o分步催化的sio _ 2溶膠為1 ~ #溶膠，相應的薄膜為1 ~ #薄膜， nh _ 3 ? h _ 2o催化的sio _ 2溶膠為2 ~ #溶膠、相應的薄膜為2 ~ #薄膜） ，在通過組裝薄膜並用透射電鏡（ tem ）觀察薄膜微觀結構以及用721分光光度計測試樣品的光透射率，得出了后兩種催化方法所制備的溶膠適合於esam法鍍膜，而第一種溶膠不適于用此法鍍膜的結論，用傅立葉紅外光譜（ ft - ir ）研究了溶膠組成；用差熱失重分析儀（ dta - tg ）對膠體進行了熱分析。
  9. Uniform and compact plzt and sno _ 2 ceramic targets, which diameter were 212mm and 221mm, respectively, had been successfully fabricated. ( 2 ) a rotating magnetic field rf magnetron sputtering system had been designed and set up, which showed high utilization efficiency of target, high films uniformity, and high deposition rate, etc. ( 3 ) the plzt and sno _ 2 thin films were investigated by afm, xrd, sem, and spectral photometer. the optimized processing parameters of preparing these films had been found

    並以此為基礎分別制備了緻密、均勻、平整、直徑為212mm的plzt和221mm的sno _ 2陶瓷濺射靶材; （ 2 ）為克服現有磁控濺射設備的不足，提出了一種新的磁控濺射方案，採用該方案的設備具有:靶材利用率高、鍍膜均勻、成膜速度快等特點; （ 3 ）運用afm 、 xrd 、 sem以及雙光路分光光度計等分析手段對plzt和sno _ 2薄膜的微結構和性能進行研究，找到了制備plzt電光薄膜和sno2透明電極材料的最佳工藝條件。
  10. At present, three - dimension dysmorphism mold can be designed and manufactured, precise impact and precise injection process can be conducted in the corporation. it has the deep - processing ability in printing, gilding, welding, painting and vacuum shielding

    公司現在可以設計製造三維異形模具，精密注塑加工，精密沖壓加工，並具有高技術的印刷燙金溶接塗裝和真空鍍膜等深加工能力。
  11. The average transmittance at a wavelength of 3 ~ 5 m of sapphire coated with one layer of sio2 antireflective films on two sides can reach 96. 43 %. so as to the transmittance of coated sapphire can satisfy the demand of window and dome applications

    藍寶石襯底雙面鍍sio _ 2膜，在3 5 m波段范圍內，平均透過率達到96 . 43 ，滿足了導彈頭罩的設計使用要求。
  12. The analyses given in this paper to quasi - three - level for 946 nm laser are complete. the relation between 946 nm laser transmission and optimal crystal length has been derived from the rate equations describing the population inversion and the photon density in the laser cavity in the steady - state case. the minimal claims to coating have been given on the base of contrasting 946 nm transmission with 1064 nm transmission in the condition of different cavity losses and how the pump beam radius in the laser crystal and optimal crystal length affect the laser threshold and output power of 946 nm laser has been given as well

    對產生946nm譜線的準三能級結構給出了較為完整的分析，利用激光諧振腔處于穩態時的速率方程，導出了準三能級nd ： yag946nm起振時，透射損耗與最佳激光晶體長度的關系，在與1064nm透射損耗相比較的基礎上，給出了不同的腔損耗情況下的最低鍍膜要求，並且給出了激光閾值、輸出功率和最佳激光晶體長度及泵光光斑大小的關系，這為設計室溫下高效運轉的946nm激光器的提供了理論基礎，這種分析方法對研究此類低增益，準三能級或三能級激光系統輸出特性有借鑒意義。
  13. With the development of infrared tunable opo, its application is more and more wide. lt is possible for us to estimate the quality of resonant mirrors in laser with high energy and to improve the output energy of laser, by measuring the reflectivity of resonant mirrors of coil and df laser by cavity - ring - down which use output wave of opo as the laser source, instead of coil and df laser with high price and huge space

    用opo紅外輸出激光作為光腔衰蕩的光源代替價格昂貴、體積龐大的氧碘和氟化氖激光器，對其諧振腔鏡的高反射率進行測量，以達到對高功率激光器腔鏡高反膜質量的評價，為改進膜系設計、鍍膜工藝優化和提高激光器的輸出能量提供理論依據。
  14. The realization of the algorithm drives the research of micro - electron structure. 2. the la2o3 thin film is prepared by rf technology, the film is analyzed by arxps, the thickness is calculated by quantitative analysis software, the thickness of sio2 thin film between la2o3 and si is 0. 6nm

    利用射頻濺射鍍膜技術在si片上制備了la _ 2o _ 3膜，通過變角xps分析和多層結構的定量計算，測得la _ 2o _ 3與si襯底之間的sio _ 2層厚度為0 . 6nm 。
  15. High - quality flow controller, pressure transducer, pressure gauge ect. for vacuum equipment, coating equipment and semiconductor equipment

    用於真空鍍膜、真空濺射、半導體製造設備的質量流量計、壓力傳感器、壓力表及相關產品。
  16. On the other hand, we design the vacuum equipment to research the coating technology using explosive wires

    此外，利用裝置的初級能源系統，設計了利用爆炸絲在真空腔中鍍膜的裝置。
  17. The central frequency and bandwidth of ln one - dimension anisotropic aeo device are determined by experiment. the changing rate of central frequency of ln

    設計工作包括利用傳輸線的瑪森等效電路理論確定這兩個器件的壓電換能器最佳鍍膜結
  18. A special clamp for etching optical fiber and depositing pd film on the fiber is designed. designed a encapsulation set of the characteristics that is dampproof, shake and eroding resisted. the experimental set - up for hydrogen sensing includes the light source, gas cell, mass flow controller, stainless steel helical tubing and the detector, etc. the experimental results are also discussed

    本文還設計了一套光纖腐蝕用夾具、光纖封裝加熱夾具和一套光纖濺射鍍膜實驗夾具;設計並製作了一套具有防潮、抗震和抗腐蝕功效的光纖傳感頭封裝裝置;設計了一套由激光器、反應混合氣室、光功率計、質子流量計和流量控制器等組成的氫氣定標實驗裝置並對實驗數據進行了分析與處理。
  19. Research for the stability of laser polarizers specialty : atomic and molecular physics postgraduate : zhao yuanan advisor : yang xiangdong with the development of optical film techniques, optical film widgets have been used widely, so researches for the stability of optical film widget is become more and more important

    隨著光學薄膜技術的不斷發展，光學薄膜器件的應用日益廣泛，光學薄膜的穩定性研究也被提到了極其重要的地位。為了解決大功率激光器中激光偏振膜的穩定性問題，本課題從鍍膜材料特性、膜系設計、沉積工藝等方面對這一問題展開了深入的研究。
  20. The studies suggest that the antireflection coating has excellent properties as the result of film design, and will be widely used in the fiber optical communication industries

    研究表明，以膜系設計的結果為參照，實際所鍍膜層性能優異，在光纖通訊領域具有廣闊的應用前景。
分享友人
分享到 Line

分享到臉書