鍛燒 的英文怎麼說

中文拼音 [duànshāo]
鍛燒 英文
roasting
  • 鍛 : 動詞（把金屬加熱后捶打; 鍛造） forge
  • 燒 : Ⅰ動詞1 （使東西著火） burn 2 （加熱或接觸某些化學藥品、放射性物質等使物體起變化） cook; bake; hea...
  1. Blende roasting furnace

    閃鋅礦鍛燒爐
  2. The hydrocarbon content of this phosphate ore provides most of the heat needed for the calcination.

    這磷礦所含烴量能提供鍛燒所需的大部分熱量。
  3. We possess accurate processing equipments, such as hydrogen making equipment, reducing furnace, isocratic press machine, 500t capacity hydraulic machine, intermediate frequency induction furnace, high or low temperature fritting durance and forging equipment, which forms whole production line

    公司擁有制氫裝置、系列制粉還原爐、等靜壓力機、 500噸油壓機、中頻感應爐、高低溫燒結爐、鍛造設備及精密加工設備。
  4. Many years ago men first heated iron ore in a fire.

    許多年前，人們初次在火中鍛燒礦石。
  5. Indirect methods of determining the frost resistance of roofing tiles ; determination of drying shrinkage and firing shrinkage

    房頂瓦抗凍性能直接測定法.測定乾燥收縮率和鍛燒收縮
  6. The final stage in the production of dead burned dolomite requires that the " green briquettes " produced in the briquetting area be treated by application of very high temperatures for a period of time

    在鍛燒白雲石產品的最後工序里，要求對在塊狀區域產生的「綠色煤球」進行一段時間的高溫熱處理。
  7. Exercise helps control and burn body fat and it strengthens and tones muscles as well as improving posture

    運動有助身體脂肪的控制及燃燒，增強及鍛?肌肉的發展，以及改善身型體態。
  8. How to reduce the burning loss rate of forge piece

    如何降低鍛件的燒損率
  9. The reason for crankshaft fracture in an mwmtbd234v6 diesel was analyzed. the results show that overheating and overburning is the direct reason for fracture. the heat treatment of the crankshaft is not perfect or consistent with the standard. the lubrication is not good in service. all these accelerate the fracture

    分析mwmtbd234v6型柴油機的曲軸斷裂原因，結果表明鍛件過熱過燒是導致斷裂的直接原因；曲軸熱處理工藝不規范、不完善，曲軸工作潤滑條件不良加速了曲軸斷裂
  10. As - sintered hardmetal pellets used in heading dies. dimensions and tolerances

    鐓鍛模用的燒結硬質合金片.尺寸和公差
  11. Alumina calcination plant

    氧化鋁鍛燒車間
  12. Conditions of calcination

    鍛燒條件
  13. The design of nanostructure and processing of ti - pillared montmorillonites was been described in this paper

    摘要將聚羥基鈦離子插入粘土礦物層間，羥鍛燒形成納米二氧化鈦柱撐的粘土材料。
  14. The intrinsic chemical reaction rate constant was insensitive to the precursor and the calcinations history of cao, but the product layer diffusivity was affected by these two factors in the initial stage and decreased to a constant value with increasing conversion of cao

    化學反應速率常數不受氧化鈣的先驅物與其鍛燒程序所影響，但產物層擴散系數在初始階段則受到上述兩因素的影響，並隨著氧化鈣的轉化而減少至一定值。
  15. The results show that : the fillers of sio2 based investment consist of sio2, al2o3 and mgo, and the binder is nh4h2po4 for sio2 based investment, the bulk density and the compression strength decrease, the apparent porosity and the thermal expansion increase, when the specimens are heated to 900 ; the fillers of al2o3 based investment consist of al2o3 and mgo, and the binder is nh4h2po4 ; for al2o3 based investment, the bulk density decreases and the apparent porosity increases when the specimens are heated to 900 ; the fillers of mgo based investment consist of mgo and al2o3, and the binder is ca cement ; for mgo based investment, the compression strength decreases and the thermal expansion increases greatly when the specimens are heated to 900

    結果表明：氧化硅系包埋料的骨料是氧化硅、氧化鋁、氧化鎂，結合劑為磷酸二氫銨，其900鍛燒后顯氣孔率增加，體積密度下降，耐壓強度降低，熱膨脹增大；氧化鋁系包埋料的骨料是氧化鋁和氧化鎂，結合劑為磷酸二氫銨，其900燒后顯氣孔率增加，體積密度下降，熱膨脹變化不大；氧化鎂系包埋料的骨料是氧化鎂和氧化鋁，結合劑是鋁酸鈣水泥，其900燒后耐壓強度明顯降低，熱膨脹明顯增大。
  16. Specification for hardmetal dies and associated hardmetal tools - dimensions and tolerances of as - sintered hardmetal pellets used in heading dies

    硬質合金模具和配套硬質合金工具規范.第4部分:頂鍛模用硬質合金燒結模坯尺寸和公差
  17. During the preparation process of the solid solution, a series of effect conditions were discussed such as ph value, si / h2o, the content of ligant, the surface active agent, the aging temperature, the drying means, the drier gel calcine and their effects on the gel quality, the process of sol - gel, the granular of powder and the density of the pellets, from which the best reaction condition was found

    在制備過程中系統地研究了各種反應條件如ph值、 sal ； o 、絡合劑的添加量、老化溫度、乾燥方式、干凝膠的鍛燒方式等對溶膠「的質量、溶膠凝膠過程、粉體粒度及燒結體密度等的影響，確定了最佳反應條件：三、以li 。石i 。 。
  18. The relation between addition content of calcined kaolin, aluminium powders and aluminum sulfate in concrete and compressive strength, slump constant, 30min slump and permeability altitude were studied, and according to the experiment results, the component percent contents of crack - resistant and water - repellent admixture in cement were determined as following : calcined kaolin 6 %, aluminum sulfate 4 % and aluminium powders 0. 005 %

    通過對煅燒高嶺土、鋁粉、硫酸鋁在混凝土中摻量對其抗壓強度、初始武漢理工大學碩士學位論文坍落度、 3omin坍落度保留值及透水高度的影響，確定了配製抗裂防水外加劑的各組成成分以其占水泥質量的百分比分別為:鍛燒高嶺土6 % ，硫酸鋁4 % ，鋁粉為0 . 005 % 。
  19. In similarity, r - tios / t - zro2 powders in well - crystallized forms were obtained after heat - treated at 400 ? for two hours while zrtio, pow ' ders were successfully obtained after heat - treated at 1200. surface modification of nanosized rutile phase powders coated by organic and inorganic reagents were studied

    類似地，對tio ;億roz復合粉體進行鍛燒，在1200保溫3h即得到了zrtiq .陶瓷粉對自製納米金紅石型粉體進行了有機和無機改性研究，研究了納米粉體的分散行為。
  20. Tangshan nikka factory set up tangshan nikka mineral products co., ltd. in tangshan development area of advanced technology in 2003, which mainly exploit and produce advanced precision casting sands and other minerals. to enlarge the product market, broaden the sales channel, develop the new product and build the new market, we set up three sales departments, for promoting sales and exploiting new products

    唐山日加礦物有限公司於2003年在河北省唐山市高新技術開發區成立，並全套引進日本生產線以及生產和管理技術，主要是從事精密鑄材和其它礦產品的研究開發與生產。產品以鍛燒高嶺土為主，工廠可以提供各種用於精密鑄造的產品，涵蓋200mesh 1 . 5mm等各種規格。
分享友人
分享到 Line

分享到臉書