鎢極 的英文怎麼說
中文拼音 [wūjí]
鎢極
英文
tungsten electrode-
Before repairing, basing on the actual working condition, concerning the weldability, stress and deformation issues, the scheme of the cold welding technology whose essential being gtaw, low temperature preheating, postweld hammer the welded seam was established
修理前,圍繞兼顧解決焊接性、應力和變形問題,結合實際施工條件制定了以手工鎢極氬弧焊、鎳基焊絲、焊前低溫預熱、焊后錘擊焊縫為要素的冷堆焊工藝。Remelt hardening technology of camshaft with tungsten inert gas arc
凸輪軸的鎢極氬弧重熔淬火工藝5 all single - sided groove joints in nickel alloys, stainless steel and ferritic alloys containing more than two ( 2 ) percent chromium shall be welded using a gas tungsten - arc root pass with an inert gas back purge
鉻含量超過2 %的鎳合金、不銹鋼和鐵素體合金的單面坡口焊道用鎢極氣體保護焊,其根部焊道用惰性氣體反吹。Automatic tig welding technology on manufacture of the micro motor shell
電機機殼薄壁鋼筒自動鎢極氬弧焊技術Simulation on tig welding of aluminum alloy plate and residual stress predicting
鋁合金平板鎢極氬弧焊數值模擬與殘余應力預測Abstract : with the aids of computer ' s hardware, executive mechanism of weld arc length automatic controller of all - position pipe welder and additional software, an automatic system for arc striking has been developed, in which touch - starting method using tiny current is introduced. utilizing this method, the ablation ratio of tungsten electrode and tungsten inclusion ratio of welded seam is far smaller than normal touch - starting method. and the successful ratio of arc striking is high
文摘:用全位置自動焊管機弧長自動控制系統的計算機硬體和執行機構,僅增加部分程序,設計了採用小電流接觸引弧法的自動引弧系統,鎢極燒損和焊縫夾鎢遠小於普通的接觸引弧方式,引弧成功率很高。Wps standard welding procedure specification - gas tungsten arc welding of aluminum m - 22 or p - 22, 10 through 18 gage, in the as - welded condition, with or without backing
在焊接條件下有或沒有墊板10到18規格m - 22 p - 22鋁的氣體保護鎢極弧焊的標準焊接程序規范Firstly, backing with double - sided in - phase welding, welding method is gtaw. secondly, after filling outside one layer, welding with saw. finally, weld the inside with saw
先用雙面同步焊打底,焊接方法為鎢極氬弧焊;然後外側用焊條電弧焊填充一遍后再用埋弧焊焊接;最後用埋弧焊焊接里側。One - side welding and double - forming welding procedure of ta2 argon tungsten - arc welding
2的鎢極氬弧焊單面焊雙面成形焊接工藝研究The arc physical characteristic of mixed gases ( ar + he + co2 ) and its effects on weld shaping were discussed
摘要採用鎢極氬弧焊對不同比例氬氦二氧化碳混合氣體的電弧物理特性及其焊縫成形進行了實驗。Welding procedure specification for gas tungsten arc welding
鎢極惰性氣體保護焊工藝方法Tig tungsten - arc inert - gas welding
鎢極電弧惰性氣體保護焊Tig welding rods and solid wires for mild steel and low alloy steel
低碳鋼及低合金鋼用惰性氣體保護鎢極電弧焊條及焊絲Manual tungsten electrode
手工鎢極Tungsten inert gas
鎢極惰性氣體保Welding consumables - rods, wires and deposits for tungsten inert gas welding of non alloy and fine grain steels - classification
焊接用料.非合金和細晶粒鋼和鎢極惰性氣體保護用的焊條,焊絲和沉積物.分類Welding and allied processes - joint preparation - metal inert gas welding and tungsten inert gas welding of aluminium and its alloys
焊接和相關工藝.接頭的準備.鋁及其合金的金屬極惰性氣體保護焊和鎢極惰性氣體保護焊Specification for approval testing of welders when welding procedure approval is not required - tig or mig welding of aluminium and its alloys
不要求批準焊接工藝時焊工的鑒定考試規范.第2部分:鋁及鋁合金鎢極惰性氣體保護電弧焊或熔化極惰性氣體保護電弧焊Welding and allied processes - recommendations for joint preparation - part 3 : metal inert gas welding and tungsten inert gas welding of aluminium and its alloys
焊接和相關工藝.焊縫準備的推薦方法.第3部分:鋁及其合金的金屬極惰性氣體保護焊和鎢極惰性氣體保護焊In order to study the effect of metal fabric and distortion of work piece in tungsten inert gas ( tig ) welding rapid prototyping and obtain the height and variety range of metal parts, the method of the laser vision detecting was used to establish a detecting system to analyze the obtained image
摘要為了研究鎢極惰性氣體保護焊( tig )快速製造中金屬結構成形的效果及工件變形情況,獲取金屬結構高度及其變化范圍,通過對激光視覺傳感所得到的圖像進行分析,採用激光視覺檢測的方法,製作了一種激光視覺檢測系統。分享友人