鏈形裝置 的英文怎麼說

中文拼音 [liànxíngzhuāngzhì]
鏈形裝置 英文
chain device
  • 鏈 : Ⅰ名詞1. （鏈子） chain Ⅱ動詞（用鏈栓住） chain; enchain Ⅲ量詞（計量海洋上距離的長度單位） cable length
  • 裝 : Ⅰ名詞1 （服裝） dress; outfit; attire; clothing 2 （演員的化裝品） stage makeup and costume Ⅱ動詞...
  • 置 : 動詞1. （擱; 放） place; put; lay 2. （設立; 布置） set up; establish; arrange; fix up 3. （購置） buy; purchase
  • 裝置 : 1 （機器設備的配件）installation; device; apparatus; equipment; arrangement; gear; appliance; rig...
  1. Information linking built by cv present the subject characteristics of information entities over internet. cv acts as information browsing tool and retrieval refining device therefore refresh and deepen user ' s knowledge horizon. application of cv can be divided into function level and technical level with corresponding standard in the wis

    受控語言針對web信息內容的主題特徵來建立信息鏈接，通過「用、代、屬、分、參」等規范形式標識信息實體間關系特徵，成為用戶使用因特網信息的瀏覽工具和檢索凈化裝置。
  2. Based on analysis of the iso - rigidity of the gyro assembly, the requirement for making the joints match each other is offered, which has a guiding significance for joints assembly and selection. based on analysis of rigidity and drift error for the dynamically tuned gyro, a cross model including an inner and an outer flexible hinges is established

    在對動力調諧陀螺剛度和漂移誤差分析的基礎上，建立了由內外撓性接頭裝配所形成的十字型鉸鏈模型，並利用偽剛度理論對該模型進行了分析，得出了內外撓性接頭兩鉸鏈的相對位置關系對十字型鉸鏈模型的影響曲線。
  3. Secondly, calculation theory of construction for suspension bridge is presented under the ideal condition of dead load design. linetype change stiffness of cable and slip stiffness of supporting points are deduced based on segmental catenary theory. then numerical analysis method through sgkz2000 software are introduced in detail about calculating design linetype for suspension bridge, unstressed length of cable, erection linetype of cable and pre - displacement of saddle without loads, erection linetype of wire strands, the fixed position for erecting cable band and linetype of lifting stiffening girders

    其次，根據懸索橋恆載設計理想狀態建立了懸索橋施工計算原理；以分段懸鏈線索理論為基礎，推導了懸索的線形變化剛度和懸索支點的滑移剛度；介紹了懸索橋成橋設計線形計算、吊索無應力長度計算、空纜線形與預偏量計算、絲股架設線形計算、索夾安裝位置計算和加勁梁吊裝線形計算的具體方法、數值演算法及軟體sgkz2000的計算模塊的實現。
  4. A second method is to furnish the surfaces with hinges and to use an exterior sector with drilled holes for each angle setting.

    第二種方法是在翼面上裝置鉸鏈，用一個對不同安裝角鉆有不同孔的外部扇形件與之配合。
  5. Based on the analysis of designed cad graphics and the given parameters, computer can convert the cad graphics to a acdbpolyline which can simulate the routine of the conveyor chain. then by using the method of point - by - point strain calculation, computer could figure out each point ’ s strain of the chains under different load states, and get the results such as strain ’ s maximal and the minimal values and their positions, weight of the strain equipment and power of the drive electric - machinery that the conveyor need

    通過對設計的cad圖形和給定參數的分析，將輸送鏈運行軌跡轉化為一條可模擬輸送鏈軌跡的多義線，然後用逐點張力計演算法動態地計算出各種加載狀態下輸送鏈上各點的受力，得出最大、最小受力點的力的大小和位置，拉緊裝置的重量，驅動電機所需的功率等結果。
分享友人
分享到 Line

分享到臉書