鑄態硬度 的英文怎麼說

中文拼音 [zhùtàiyìngdù]
鑄態硬度 英文
as-cast hardness
  • 鑄 : Ⅰ動詞（鑄造） cast; coin; make Ⅱ名詞1. （古國名） zhu, a state in the zhou dynasty2. （姓氏） a surname
  • 態 : 名詞1. （形狀; 狀態） form; condition; appearance 2. [物理學] （物質結構的狀態或階段） state 3. [語言學] （一種語法范疇） voice
  • 硬 : 形容詞1 （堅硬） hard; stiff; tough 2 （剛強; 堅定; 強硬） strong; firm; tough; obstinate 3 （勉...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 硬度 : hardness; solidity; scirrhosity （腫瘤的）
  1. The age hardening characteristic of as - cast cu20ni20mn and cu20ni35mn alloys and the interface characteristic between the alloy and cast tungsten carbide were studied, and on the basis of this study, composites of cu - ni - mn alloy reinforced with different volume fraction ( 0 - 45vol. % ) and different size ( 42 - 362 m ) of cast tungsten carbide particles were made by vacuum hot - pressing liquid sintering technology. pin on disk two body abrasion tests have been performed with different size of sic abrasive under different loads

    本文研究了鑄態cu20ni20mn和cu20ni35mn合金的時效硬化特性及其與鑄造碳化鎢的界面特性，並在此基礎上以不同尺寸（ 42 362 m ）的鑄造碳化鎢顆粒為增強體，採用真空熱壓液相燒結技術制備了不同顆粒含量（ 0 45vol . ）的鑄造碳化鎢顆粒增強cu - ni - mn合金基復合材料；以不同粒度的sic為磨料，在不同載荷條件下利用銷?盤磨損試驗機測試了復合材料的二體磨料磨損性能。
  2. The vc - fe surface composite shows high wear - resistance, it ' s wear - resistance is 4. 20 times as that of chilling respectively. with the content of v increasing, it ' s rigidity and wear - resistance increases continually. more vc grains gained, and well distributed, better wear - resistance the vc - fe surface composite will show. ( 7 ) surface cermet composite was formed by the means of cast - sintering technique, with the help of adding wc grains and the quantity of heat sent out from the reaction v + c vc, the carbide cermet quality percent exceeds 60 %

    在重載干滑動摩擦條件下， vc一fe表面復合材料顯示了很高的耐磨性，其相對耐磨性是可淬硬鑄鐵的4 . 2倍:隨著含v量的增加， vc一fe表面復合材料的鑄態硬度和耐磨性不斷提高， vc顆粒越多，分佈越均勻，表面復合材料的耐磨性就愈好。
  3. Sintering speed increased greatly with the help of great quantity of heat of the molten iron, the great quantity of heat sent out from the carbonizing reaction and a little quantity of liquid, this sintering type is an instantaneous sintering, the sintering compacting can carry completely in a few minutes, the degree of sintering compacting is very high. ( 6 ) the vc - fe surface composite has high rigidity, it ' s rigidity exceeds 60hrc, under condition of dry sliding friction and overloading

    鑄造燒結時，過熱鐵水的巨大熱流密度沖擊、粉料壓坯中的碳化反應的放熱以及壓坯中少量液相的產生使壓坯的燒結速度大大提高，此時屬瞬間液相燒結，在十幾分鐘內燒結過程即可完成，可達到很高的緻密化程度。 （ 6 ）鑄態下vc一fe表面復合材料具有很高的硬度，其鑄態硬度） 60hrc 。
  4. The microstructure, the hardness and the wear resistance properties of the composites fabricated by semi - solid casting has been studied and analyzed metallographic analysis indicated that sic particles dispersed uniformly in the composites

    本文採用半固態復合鑄造法制備了sic顆粒增強鋁基復合材料，並對這一系列材料的微觀組織、硬度及耐磨性能進行了研究與分析。
  5. And the microstructure, the hardness and the wear resistance properties of the composites fabricated by semi - solid casting had been studied and analyzed

    本文採用半固態復合鑄造法制備了sic顆粒增強鋁基復合材料，同時研究了復合材料的微觀組織、硬度和耐磨性能。
分享友人
分享到 Line

分享到臉書