鑄造過程 的英文怎麼說

中文拼音 [zhùzàoguòchéng]
鑄造過程 英文
casting process
  • 鑄 : Ⅰ動詞（鑄造） cast; coin; make Ⅱ名詞1. （古國名） zhu, a state in the zhou dynasty2. （姓氏） a surname
  • 造 : Ⅰ動詞1 （做; 製作） make; build; create; produce 2 （假編） cook up; fabricate; concoct 3 [書面語...
  • 過 : 過Ⅰ動詞[口語] （超越） go beyond the limit; undue; excessiveⅡ名詞（姓氏） a surname
  • 程 : 名詞1 （規章; 法式） rule; regulation 2 （進度; 程序） order; procedure 3 （路途; 一段路） journe...
  • 鑄造 : [冶金學] cast-on outwell; foundry; cast; casting; found; founding
  • 過程 : process; procedure; transversion; plication; course
  1. Some other defects in castings are well - defined cracks and hot tears that develop during solidification, under combination of stress concentration from uneven contraction and the metal ' s low strength at near - melting temperatures

    鑄件內部的其它一些缺點是，凝固過程中，在不均勻收縮造成的應力集中和接近熔點溫度下金屬的低強度的綜合作用下，出現的清晰裂縫和熱撕裂。
  2. Solidification of cast aluminum matrix composites

    鑄造鋁基復合材料的凝固過程
  3. The wax setting and casting process is complicate process with a series of procedures, including model creating, spruing and construction, rubber mold vulcanization and cutting, wax models injection, stone setting in wax model, wax tree creating, investing, investment mold burning - out, metal melting and pouring, casting cooling and divesting, etc

    蠟鑲鑄造是一個多工序的復雜工藝過程，包括母版製作、開設水線、製作橡膠模、製作蠟模、寶石鑲嵌到蠟模、種蠟樹、製作石膏型、石膏型脫蠟焙燒、金屬熔煉澆注、飾件冷卻清理等。
  4. When the atomic ratio of nb is one, the structure is homogeneous and almost composed of the single sm2fe17 phase. it ' s nearly the same structure as that after annealing. so it can reduce the production cost and increase the stability of magnetic properties

    當nb的原子比為1時的鑄態組織基本為均勻的接近單相的sm _ 2fe _ （ 17 ）組織，已接近於退火后的組織，從而可以避免冗長的均勻化退火化過程而直接用於製造永磁體，極大的降低了生產成本，並能有效的提高磁性能的穩定性。
  5. On the basis of experiment, by using the exponential viscous model, a flow constitution equation of the pattern material ( w ax stock ) used in investment casting has been established. by applying it to the n umeric al simulation system, the numerical simulation on die - filling process of the fus ible pattern material ( wax stock ) used in investment casting has been successfully realized

    在實驗基礎上，採用冪律粘度模型建立了熔模鑄造用模料的流動本構方程，將其應用到數值模擬系統中，成功地實現了對熔模鑄造用模料充型過程的數值模擬。
  6. Abstract : porosity of die castings caused by air entrapped into the liquid metal in the shot sleeve is common problem of die csating process

    文摘:壓室中氣體捲入金屬液內而造成壓鑄件內部氣孔是壓鑄過程常見的問題。
  7. In grid casting operations, mold spray application involves time when no grids are produced.

    在板柵鑄造過程中，給模具噴塗也佔用時間，其間不生產板柵。
  8. Metal poured into a mold cavity during the casting process solidifies with the possibility of shrinkage, segregation or porosity, which can prevent an " as - poured " casting from being acceptable for severe applications

    在鑄造過程中，澆鑄到模腔內的金屬在凝固過程中可能會產生收縮、分離或氣孔，這些問題使得「澆鑄」鑄件無法被苛刻環境應用領域所接受。
  9. The operator input parameters through touch screen controller. melting takes between 5 and 10 minutes depending on the type and amount of metals. the casting operation is performed automatically

    透過瑩光幕輸入所需資料。金屬溶解時間取決于金屬種類及重量。整個鑄造過程均是全自動。
  10. Three factors, such as pull - up type, the materials and structure of crystallizing mould, and the temperature field in crystallizing mould, influencing on continuous up - casting for aluminum were analyzed, which laid the foundation of the application to continuous up - casting technology for aluminum bar

    分析研究了引拔拉坯制式、結晶模材料及結構、結晶模內溫度場三因素對鋁上引連鑄的影響規律，結果表明上引連續鑄造過程中施加適當頻率的反推和反推量有利於桿坯連鑄的持續，結晶模自身的性能及模內溫度場的狀態對金屬鋁桿上引連鑄工藝的實現有直接影響。
  11. Are in - process casting handling methods adequate to prevent damage

    鑄造過程的操作方式是否可以避免損傷？
  12. During the precision casting of the aviation engine ' s parts, the consumptive materials are wide variety of kinds and have a large consumption, so the importance of the material consumption management is prominent

    航空發動機零件精密鑄造過程中所用的材料種類繁多、消耗量大，材料消耗管理的重要性尤為突出。
  13. Numerical simulation of the flow - thermal field in the process of penetration casting

    滲流鑄造過程中流場溫度場的數值模擬
  14. Founding - equipment for the production of lost patterns for the lost foam casting process

    鑄造.漏泡鑄造過程用鑄模生產設備
  15. The technique is applied to buaa - cast casting process simulation system successfully

    該技術已成功地應用於buaa - cast鑄造過程模擬系統中，用於顯示鑄件整體的各物理量數據信息。
  16. Therefore, solving the technical difficulties in the iron and steel industry is in great need and of great significance, especially for the continuous casting ( cc ) process, which serves as the base of the whole iron and steel industry

    所以對鋼鐵工業生產過程中一些技術難點進行研究和改進，有著非常重大的意義。而作為后續工藝的基礎的連續鑄造過程在其中具有重要的位置。
  17. The subsystem of the casting quality data management and analysis can be used to classify and analyze casting quality information statistically, and to determine the main influencing factors and to ensure that the manufacturing process is under good control

    質量數據管理與分析子系統可以對鑄造過程的鑄件質量數據進行分類管理和統計分析，判斷影響鑄件工藝質量的主要因素，以保證生產過程的穩定。
  18. In the system, the process of adjustable pressure casting can be controlled by using two modes - manual control mode and automatic control mode

    Ty ? 1調壓鑄造機控制系統採用自動/手動兩種方式對調壓鑄造過程進行控制。
  19. Abstract : in this paper the design and manufacture of the complex tools for foam pattern in lost foam process were described by taking a typical part as an example. the result showed that not only the efficiency of the die design and manufacture was improved and the task was accomplished satisfactorily, but also the die s quality was ensured fairly and earned consumer s favorable comment by using cad / cam technology

    文摘:以典型零件為例，詳細描述了消失模鑄造復雜發泡模模具設計和製造過程，結果表明:採用cad / cam技術，不僅大大提高了模具設計及製造效率，圓滿完成了模具的設計製造任務，而且保證了模具的質量獲得了用戶的好評。
  20. In this paper the design and manufacture of the complex tools for foam pattern in lost foam process were described by taking a typical part as an example. the result showed that not only the efficiency of the die design and manufacture was improved and the task was accomplished satisfactorily, but also the die s quality was ensured fairly and earned consumer s favorable comment by using cad / cam technology

    以典型零件為例，詳細描述了消失模鑄造復雜發泡模模具設計和製造過程，結果表明:採用cad / cam技術，不僅大大提高了模具設計及製造效率，圓滿完成了模具的設計製造任務，而且保證了模具的質量獲得了用戶的好評。
分享友人
分享到 Line

分享到臉書