鑄體 的英文怎麼說

中文拼音 [zhùtǐ]
鑄體 英文
body of casting
  • 鑄 : Ⅰ動詞（鑄造） cast; coin; make Ⅱ名詞1. （古國名） zhu, a state in the zhou dynasty2. （姓氏） a surname
  • 體 : 體構詞成分。
  1. Various types of techniques have been applied to study the main principle problem. these techniques involve petrography, x - ray diffraction ( xrd ), scanning electron microscope ( sem ), carbon isotope, cathodoluminescence ( cl ), fluid inclusion, and epoxy - resin casts

    論文中所用的分析原理與技術方法包括：層序地層學分析、 x -衍射、掃描電鏡、穩定同位素、陰極發光、流體包裹體與染色鑄體薄片等。
  2. Several analysis methods such as casting slice, scanning electron microscope, porosity and permeability data, mercury injection data and density of fissures are used to study the reservoir properties of volcanic rocks in huang - yu - re area, the east sag of liaohe basin. volcanic rocks in this area are mainly composed of basalt, diabase, tuff and trachyte. the dominating type of volcanic reservoir space includes secondary solution pores and structural fissures

    通過火山巖的常規物性分析壓汞分析和裂縫密度分析，結合鑄體薄片和掃描電鏡，研究了遼河油田黃于熱地區的火山巖儲層物性特徵，認為該區火山巖儲層巖石類型主要有玄武巖輝綠巖凝灰巖和粗面巖，主要儲集空間類型為次生的構造裂縫和溶蝕孔縫。
  3. Acicular cast iron

    針狀鑄體
  4. Test method for impact resistance of resin casting body

    樹脂澆鑄體沖擊試驗方法
  5. The casting shown in section fig 1-138 has its center of gravity located as shown.

    圖1138所示截面的鑄體，其重心如圖所示位置。
  6. The flow field of the molten slag pool in the electroslag casting process was simulated by the finite element analysis software ansys, the simulated result was in accordance with the physical simulation results very well

    採用大型通用有限元分析軟體ansys ，對電渣熔鑄體系渣池流場進行了模擬研究，所得結果與物理模擬實驗結果完全一致。
  7. We also produce all kinds of high label ductalloy and gray castings, the production is up to 1000 tons

    我公司還生產各種高牌號、球墨鑄體、灰鑄體，產量可達一千噸。
  8. Observation of drilling cores and casting - sections and the characters of pore structures and permeability of the matrix of the lower - ordovician carbonate in comparing with the lower limit of a reservoir for matrix reveal that the porosity, permeability, maximum pore diameter, saturation and median throat diameter in the matrix with undeveloped fissures, holes and solution pores are far lower than those of a reservoir limit although some micro - pores are developed in the matrix which therefore has no capacity of storing and producing oil - gas

    摘要通過鉆井巖心和鑄體薄片觀察，根據下奧陶統灰巖基質的孔滲特徵和孔隙結構特徵，並與基質作為儲層的下限對照裂隙、洞穴和溶蝕孔洞不發育的灰巖基質，發現盡管有微孔隙的發育，但其孔隙度、滲透率、最大孔喉半徑、飽和度、中值喉道半徑等參數值遠低於儲層下限值，基本不具備儲集和生產油氣的意義。
  9. The generals of test methods for properties of resin casting body

    樹脂澆鑄體性能試驗方法總則
  10. The casting shown in section fig 1 - 138 has its center of gravity located as shown

    圖1 138所示截面的鑄體，其重心如圖所示位置。
  11. The present paper gives a detailed description of the dolostone reservoirs and their genesis in the zaring oil pool in southern qiangtang basin on the basis of thin sections, cast sections, capillary pressure curves and cathodeluminescent images

    摘要根據薄片、鑄體薄片、壓汞、陰極發光等研究，詳細描述了南羌塘盆地扎仁古油藏白雲巖的儲層特徵，並對白雲巖成因作了初步研究。
  12. On the basis of the study of high resolution sequence stratigraphy, this paper discusses the reservoir petrology ' s diagenesis and secondary pore of the chang 4 + 52 ~ chang 62 pay zones in detail by using the methods of analysis of mercury injection, cast section, popular section, scanning electron microscope, x - ray diffraction and etc. the reservoir rock is mainly composed of feldspar fine sandstone, which is characterized by low compositional maturity and relatively high textural mature

    本文在高解析度層序地層學研究的基礎上，通過15口井的常規物性、壓汞、鑄體分析、薄片鑒定、掃描電鏡、 x光衍射、陰極發光、粒度分析等多項測試手段，對坪北油田延長組長4 + 52長62儲層巖石學、成巖作用及次生孔隙進行了詳細研究。
  13. Test method for tensile properties of resin casting body

    樹脂澆鑄體拉伸性能試驗方法
  14. The flow of the molten slag pool determines the temperature distribution and the pool profiles in the electroslag casting process, which finally impact on the quality of ingot casting

    摘要電渣熔鑄過程中熔渣的流動決定了熔鑄體系溫度場的分佈以及金屬熔池的形狀，最終影響熔鑄鋼錠的質量。
  15. Unsaturated polyester resin - determination of stability of casting resin in basic solution

    不飽和聚酯樹脂澆鑄體耐堿性測定方法
  16. Test method for compressive properties of resin casting body

    樹脂澆鑄體壓縮性能試驗方法
  17. Test method for compressive properties of

    樹脂澆鑄體壓縮性能試驗方法
  18. Test method for flexural properties of resin casting body

    樹脂澆鑄體彎曲性能試驗方法
  19. Characteristics of cured resin without reinforcement

    樹脂澆鑄體性能：
  20. Charactertica of cured resin without enforcement

    Hr 189xg樹脂澆鑄體性能
分享友人
分享到 Line

分享到臉書