閉氣 的英文怎麼說

中文拼音 [bìqì]
閉氣 英文
breathlessness
  • 閉 : Ⅰ動詞1. （關; 合） close; shut 2. （堵塞不通） block up; obstruct; stop up Ⅱ名詞（姓氏） a surname
  • 氣 : Ⅰ名詞1 （氣體） gas 2 （空氣） air 3 （氣息） breath 4 （自然界冷熱陰晴等現象） weather 5 （氣味...
  1. The method of close water test has been used for a long time, so richer experience has been achieved. however, it not only takes pains and time, but also consumes raw materials during the close water test because of miscellaneous working procedures such as bricklaying in the two ends of pipe, water - repellent layer plastering, maintaining and water offletting, brick - block backouting after the test, especially in the region short of water and some drainage pipe with prop - pipe construction. in order to satisfy the fast development of municipal construction, new detection methods should be developed

    閉水試驗方法因其應用時間較長，目前已積累了較豐富的經驗，但在閉水試驗時，管道兩端砌築磚堵、抹防水層、養護、灌水浸泡，以及試驗后的放水、磚堵拆除等繁雜工序，不僅費工、費時，而且消耗原材料，尤其是在缺水的地區以及頂管施工的無壓管道，這些矛盾更加突出；因此，為滿足迅速發展的市政建設需要，有必要探索新的檢測方法，閉氣試驗就是其中一種，但是閉氣試驗目前還不完善，有待于進一步深入研究。
  2. 5 ) the 3 - d geometry and finite element model of the assembly of the optimized obturator of the breech mechanism is set up in terms of the optimized structural parameters. quasi - static and dynamic finite element analysis of stiffness, strength and obturating performance of the optimized obturator of the breech me chanism is performed

    利用優化后的結構參數建立了優化后炮閂閉氣結構的裝配體三維幾何實體模型和有限元模型，對優化后的炮閂閉氣結構剛強度和閉氣性能進行了準靜態及動態多體接觸彈塑性有限元分析。
  3. So although there are better oiliness in peng ii, peng iii, peng iv gas pool and there are industrial off - take potentia after compressive fracture, this gas pool belongs to lower permeability, convention sand - density sand, little to middle throat - punctate pore, sealing elasticity gas drive, partly poor water drive, normal pressure, net gas, lithologic trap to nose - like structure - lithology compounding trap model

    所以，雖然新都氣田蓬萊鎮組蓬二、蓬三、蓬四段有良好的含油氣性，且經過測試均獲得工業產能。但總體上該氣藏隸屬低滲常規砂巖?緻密砂巖，小及中喉?細孔孔隙型，定容封閉彈性氣驅，部分弱水驅，常壓，干氣，巖性圈閉及鼻狀構造?巖性復合型圈閉氣藏類型。
  4. ( 3 ) wheatgrass could reduce water dissipation by shutting up stoma and let some leaves wither

    3 、冰草植株在乾旱條件下關閉氣孔，以減少水分散失，葉片萎蔫，以減少蒸騰面積。
  5. Development of an insulating plate with seal air cavity

    一種帶有封閉氣腔的保溫板研製
  6. The structure of diapirs can be regarded as the result of the pressure of inner gases upthrusted from the lower strata, and the migration of gases from deeper strata

    底辟構造可能是地層內部圈閉氣體由於壓力釋放上沖的結果，也可能是氣體向上運移的通道。
  7. Study on multi - thread communication in automatic detecting device for gas lock valve

    閉氣塞自動檢測系統多線程通訊實現的研究
  8. 4 ) the method for rapid implementation of parameterized modeling of geometry and finite element of structure through a universal cae software ( msc. patran ) is researched, and parameterized modeling of the obturator of the breech mechanism is accomplished using the method

    研究了在通用cae軟體（ msc . patran ）環境下，快速實施結構幾何和有限元參數化建模的方法，並對炮閂閉氣結構實施了參數化建模。
  9. Application of structural optimization and nonlinear finite element technique to nonlinear multi - component structural system ( assembly ) is studied for the sake of the obturator of the breech mechanism of an automated mortar. the method and technology for optimizing nonlinear multi - component structural system with contact is mainly researched in this thesis

    以某自動迫擊炮炮閂閉氣結構為背景，對結構優化與非線性有限元技術在多構件非線性結構（裝配體）系統中的應用進行研究，著重在對存在接觸關系的多構件非線性結構系統進行優化設計的方法和技術途徑方面進行了研究和探索。
  10. 3 ) a 3 - d geometry and finite element model of the assembly of the obturator of the breech mechanism is established. quasi - static and dynamic finite element analysis of stiffness, strength and obturating performance of the obturator of the breech mechanism is carried out, based on elastoplastic theory and multi - body contact algorithm, and the simulation results coincide with experimental results, further, th e effect of friction factor on its obturating performance is investigated

    建立了炮閂閉氣結構的三維裝配體幾何實體模型和有限元模型，對炮閂閉氣結構剛強度和閉氣性能進行了準靜態及動態多體接觸彈塑性有限元分析，分析結果與試驗結果相吻合，進一步研究了摩擦系數對其閉氣性能的影響。
  11. Graphical user interfaces are developed to be convenient for implementing of parameterized model and debugging of program parameters. program of optimization based on ga is designed to optimize obturating performance of the obturator of the breech mechanism, further, the effect of control parameters of ga and friction factor on the optimal structure is studied

    開發了實施參數化建模和程序參數調試的界面，編制了遺傳演算法優化程序，對炮閂閉氣結構進行了閉氣性能優化，並研究了遺傳演算法運行的控制參數對優化結果的影響以及摩擦系數對最優結構形式的影響。
  12. Success in optimizing the obturating performance of the obturator of the breech mechanism shows that the method and technology for optimal design of nonlinear multi - component structural system with contact put forward in this thesis is effective and practical. structural optimization problems that are difficult to solve through the optimization method available in the universal cae software can be accomplished by means of this method

    對炮閂閉氣結構閉氣性能優化的成功說明了本文提出的對存在接觸關系的多構件非線性結構（裝配體）系統進行優化設計的方法和技術途徑具有實用價值，可以解決在通用cae軟體中現有優化演算法難以解決的結構優化問題。
  13. Comparison of stiffness, strength and obturating performance of the initial obturator of the breech mechanism with those of the optimized one is made, which indicates that the stress concentration that leads to fatigue failure in the optimized structure is eliminated. the flexibility of the optimized obturator of the breech mechanism is considerably increased and its obturating performance is substantially improved

    對優化前後炮閂閉氣結構剛強度和閉氣性能進行了對比，優化后的結構應力集中問題得到了有效控制，消除了潛在的疲勞源，結構的柔性得到很大程度的提高，閉氣性能有了明顯改善，實現了優化的目的。
  14. Cook did not timely for them to shut down valves, flame lit storesand store fuel, the fire from spreading, the flames billowed into the three - story - high, the residents along the street floor, more than 10 households in the immediate evacuation of closing a window and consciously

    因廚師未及時關閉氣罐閥門，火苗點燃店面的雨棚和店內可燃物后，火勢蔓延，火舌直沖三層樓高，居民樓臨街的十余戶居民立即關窗並自覺疏散。
  15. Analyzed 8 kinds of regulated plugs. calculating and analyzing results showed : ( 1 ) the most sensitive parts of all the plugs were near the bottom of axes of the notch, which was easily into auxiliary when under high pressure and caused unbalance or break of plugs. ( 2 ) comparison of 8 kinds of plugs proved that the design of plug of primer 9 second was optimization because it was in plastic under increase and decrease in pressure

    對國內8種制式閉氣塞：底- 9乙式底火閉氣塞、海130底火閉氣塞、海76炮彈底火閉氣塞、底- 5底火閉氣塞、底- 4底火閉氣塞、底- 8底火閉氣塞、底- 25底火閉氣塞及底- 125底火閉氣塞分別進行了有限元數值分析，計算結果表明： （ 1 ）閉氣塞凹槽底部靠軸心處為其機械強度最為敏感區域，在承受高壓過程中易破裂。
  16. In the simulation of close gas test, the location of most possible leakage of pipe is judged according to the changing speed of gas pressure at difference leakage positions

    在閉氣試驗時，可通過不同漏氣點壓力值的變化速度的快慢來判斷最不利管段的位置。
  17. Rigid cellular plastics - determination of volume percentage of open cells and closed cells

    剛性泡沫塑料製品.開口和封閉氣室容積百分數的測定
  18. 5. effect of recovery methods after thawing after thawing, the highest viability was obtained when beads of pavlova viridis were incubated in culture medium for 48h in darkness at room temperature. as to other two algae, the suitable recovery method was to incubate beads over saturated nacl solution in a closed jar for 12h in darkness at room temperature

    （ 5 ）化凍后恢復方法的影響化凍后，綠色巴夫藻的膠球在培養基中室溫下暗放置48h后存活率最高；另兩種金藻在含有過飽和的nacl溶液（ 75 % rh ）的密閉氣相中室溫下暗放置12h存活率最高。
  19. Foam glass is a new kind of inorganic heat insulating material with a structure of equally closed cells. it is mainly made of glass added with adequate foaming agents after heating and baking in high - temperature tunnel furnace, then annealing and cooling

    泡沫玻璃是一種以玻璃為主要原料，摻入適量發泡劑，通過高溫遂道窯爐加熱焙燒和退火冷卻加工處理后制得，具有均勻的獨立密閉氣隙結構的新型無機絕熱材料。
  20. The non - structural gas reservoirs in ordos basin can be divided into 4 types, such as a reservoir of lithologic trap of sandstone lens, lithologic trap of differential diagenesis, overlying lithologic - formation trap and the reservoir related with weathering and uncomformity surface

    摘要鄂爾多斯盆地非構造氣藏可分為4類：砂巖透鏡體巖性圈閉、差異成巖作用形成的巖性圈閉、上傾巖性地層圈閉、與風化殼和不整合面有關的巖性地層圈閉氣藏。
分享友人
分享到 Line

分享到臉書