間隙加油 的英文怎麼說

中文拼音 [jiānxìjiāyóu]
間隙加油 英文
intermittent oiling
  • 間 : 間Ⅰ名詞1 （中間） between; among 2 （一定的空間或時間里） with a definite time or space 3 （一間...
  • 隙 : 名詞1 （縫隙; 裂縫） crack; chink; crevice 2 （空閑） gap; interval 3 （漏洞; 機會） loophole; op...
  • 油 : Ⅰ名詞1 （脂肪; 油脂） oil; fat; grease 2 （姓氏） a surname Ⅱ動詞1 （用桐油、油漆等塗抹） apply t...
  • 間隙 : （空隙） interval; gap; freedom; space; [機械工程] clearance; separation; stricture; clear; inter...
  1. The result is that this gas pool has simple structure, only forms a little nose - like structure at the district of fenghuangshan ; this pool belongs to delta front sub - facies sedimentary model, the underwater distributary channel and mouth bar is the better sedimentary microfacies ; the physical property of the reservoir is poor, the type of pore of the reservoir rock mostly are intergranular pore, intergranular solution hole and little are intercrystalline micropore ; the influential factors of pore structure and physical property are lithofacies, lithologic character and diagenesis ; the off - take potentia of all the testing well are deadly shortness, the wells have the worth of industrial recovery only under the condition of going through sand fracturing, and in the early of binging into production, the oil and sheath pressure drop rapidly, the production of the well drop rapidly

    研究認為該氣藏構造簡單，只在鳳凰山形成了一個小型的鼻狀構造；屬於三角洲前緣亞相沉積模式，水下分流河道和河口壩是有利的沉積微相；儲層物性差，儲層巖石的孔隙類型主要有粒間孔、粒間（內）溶孔及少量晶間微孔；影響蓬萊鎮組氣藏儲層孔隙結構及儲集性的因素有巖相、巖性條件及成巖作用；所有測試井自然產能都極低，必須經加砂壓裂后才有工業開采價值，且投產初期，油套壓下降較快，氣井產量下降迅速。
  2. Unlike oil pumps for traditional industries, our dry pumps are specified for the use of semiconductor companies. the rotor of vacuum space is not sealed with oil, but with the application of the minute clearance and high - speed rotation. therefore, a special demand is laid on the precision manufacture techniques, assembly procedures and profile design of roots rotor

    以乾式真空幫浦為例，在2001年2月第一臺賣出去以來，已賣出數百臺，本乾式真空幫浦等級屬於半導體廠專用乾式真空幫浦，不同於傳統產業使用的油式真空幫浦，旋轉轉子真空腔體內不用油去密封，而是用微小的間隙配合高速旋轉的轉子進行密封，因此特別講究精密加工技術精密組裝技術魯氏轉子線型設計。
  3. This new technology changes from the traditional method by which the induced and compressor wheel separately are designed and produced to a new one by which the one - piece compressor is designed. on the basis of this new technology and the optimum blade profile, the performance of both the compressor and the turbocharger is largely improved. through the heating power calculation of the compressor, the analysis of the surge and the block of the compressor, the test - bed performance test of the turbocharger, the matching test of turbocharger and diesel engine, the propulsion test of the turbocharger on plateau condition, it is proved that the newly - designed compressor not only has high efficiency, but also improves the flow distribution in the high efficiency area so that the propulsion line can run through the high efficiency area

    主要內容包括：提出一種全新的壓氣機葉輪技術和概念，這種技術將傳統的導風輪和壓氣機分開設計、單獨加工改為整體設計、整體加工的單體葉輪；從增壓器與柴油機配機計算所得出的基本參數出發，通過對壓氣機進行熱力計算，確定壓氣機的基本結構參數；再對葉型以及葉輪輪廓與葉輪罩殼的配合間隙進行優化，對新設計的壓氣機進行喘振和堵塞分析；通過增壓器平臺性能試驗，驗證了新設計的壓氣機的性能水平得到了較大的提高，達到了提高增壓器的整體性能水平的目的；通過增壓器與柴油機配機試驗、以及增壓器用於高原條件下的牽引試驗，驗證了新設計的壓氣機不但具有高效率，還改善了高效率區的流量分佈，使牽引特性線貫穿高效率區。
  4. This product belongs to high - grade compound to be refined through high - tech means, holds the excellent functions of rapidly rehabbing worn engine, after changing engine oil, adding it can avoid cylinder scraping and burning, wholly exhaust black smoke and engine powerless, also, it can restore the crack of the damaged engine and keep engine sealed meanwhile increase cylinder pressure, exhaust smoke when burning motor oil

    本品為高科技提煉的高級油品化合物，具備對己磨損的發動機進行快速修復的卓越功效，在更換機油后添加本品可有效避免拉缸、燒缸，徹底清除黑煙及引擎乏力現象，對己磨損的引擎間隙進行修復，保持引擎密封功能、提高氣缸壓力、清除燒機油、冒黑煙等現象。
  5. The numerical results show that : with the enhancement of er effects, the bearing capacity is obviously increased ; the increase magnitude is larger when small radius clearances and large eccentricity ratios ; at low shear rates, the influence of er effects on the lubrication performance of journal bearings are more obvious

    數值研究表明：隨著電流變效應的增強，軸承潤滑油膜的承載能力明顯提高；軸承半徑間隙越小，偏心率越大，軸承承載能力增加的幅度也越大；在低剪切速率下，電流變效應對軸承潤滑性能的影響較大。
分享友人
分享到 Line

分享到臉書