閥位置 的英文怎麼說
中文拼音 [fáwèizhì]
閥位置
英文
evegr valve position egr-
Turn both handles of the rotary slide valve ( pos. no. 15 ) and the clutch to the emergency position, and the annunciator “ emergency ” is lit on
轉動旋轉滑閥15和離合器手柄到應急位置,指示器「應急「燈亮。Nibco iron body check valves may be installed in both horizontal and vertical lines with upward flow
美國尼伯科止回閥可以安裝在水平位置,或流向朝上的垂直位置。Nibco iron body check valves may be installed in both horizontal and vertical lines with upward flow or in any intermediate position
尼伯科鑄鐵閥體止回閥可以安裝在水平管線或流向朝上的垂直管線中的任何位置上。Epos egr valve position
廢氣再循環控制閥位置Install a minimum of 1 " above flood level of fixture if factory deck mounted or not less than 6 " if general plumbing field application
安裝時要使閥蓋側面朝上,要便於測試和維修。不要安裝在隱蔽的位置或區域,在這些地方,由於閥內件正常磨損產生的水泄漏可能導致閥門損壞。Therefore, a new design of the flexible joint is herein assumed by replacing the spring / damper system by a hydropneumatic system in which a horizontal hydraulic cylinder only is needed to be fitted between the two bell cranks and the rest of the hydro - pneumatic system which are the throttle valve and the accumulator can be suspended on the vehicle frame at any convenient place
因而,此處採用新型撓性連接設計,用液壓氣動系統替代彈簧減振器裝置,液壓氣動系統兩曲柄間只需安裝一個臥式液壓缸,而其他部件(即減壓閥和蓄能器)可懸置於車架的適當位置。Now close the throttle to the idle position and connect the glow plug cord. the engine is now ready for starting
節流閥到低速位置,接上火星塞電池,引擎已經準備啟動。Internal stops provide positive over travel protection for power actuated valves and act as a reference to position the discs in the open and closed positions
內置的止動裝置為動力執行機構提供行程保護,並且作為參考坐標在開啟和關閉位置定位閥瓣。With the handwheel / turn indicator sleeve assembly still at its balance set point indication, reinstall them on the valve stem and hold in place with the 1 / 4 " retaining bolt
這時手輪/旋轉指示器套筒總成仍然位於平衡設置指示點上,將它們重新安裝到閥桿上,並用1 / 4英寸固定螺栓固定在其位置上。A double check valve assembly shall be installed at each noted location
雙止回閥總成應該安裝在每個指定的位置。Series 719 double check valve assembly shall be installed at each noted location
系列719雙止回閥總成應該安裝在每個標注的位置上。Double check valve assembly shall be installed at each noted location to prevent the unwanted reversal of polluted water into the potable water supply
雙止回閥總成應該安裝在每個值得注意的位置,用於防止污水出現不需要的迴流而流進飲用水供應系統中。Insert stem into stem opening and press in to full - closed position
將閥桿插入閥桿開口處,並將其壓進全閉的位置。Position indicators allow at - a - glance determination of whether valve is in open or closed position
位置指示器使得操作者能夠一眼看出閥門是處于開啟還是關閉的位置。Secondly, this paper emphasizes how to apply this new friction model to practical valve controlled cylinder position servo system and realize the dynamic friction compensation. the paper designs the compensation law and uses the matlab / simulink tools to testify the compensation effect
其次,本文重點放在如何將新型摩擦模型應用到實際的電液位置伺服系統中,以實現對閥控液壓缸電液位置伺服系統的摩擦力進行動態補償,並應用matlab的simulink模擬工具進行模擬,通過調節摩擦補償環節的參數可得到良好的補償效果。Stem : the tee - head disc - stem connection prevents lateral strain on the stem for smooth, easy operation. accurately cut threads engage the yoke sleeve for positive control of disc position
閥桿: t形閥瓣-閥桿連接防止施加在閥桿側面的應力,確保操作平穩順暢容易。軛架套管準確的螺紋連接有助於閥瓣位置的調整控制。Tvps throttle valve position switch
節流閥位置開關Evp egr valve position sensor
廢氣再循環控制閥位置傳感器Note : ? for intermediate valve positions the flow coefficient table can be used to determine actual flow between graph positions
注意: - -對于中間閥位置,可以利用流量系數表來決定曲線圖位置之間的實際流量。Industrial - process control valves - mounting details for attachment of positioners to control valves - positioner mounting on linear actuators
工業過程式控制制閥.控制閥位置控制器的安裝詳圖.位置控制器在線性執行機構上的安裝分享友人