阻尼損耗 的英文怎麼說

中文拼音 [zǔnísǔnhào]
阻尼損耗 英文
damping loss
  • 阻 : 動詞（阻擋; 阻礙） block; hinder; impede; obstruct
  • 尼 : 名詞（尼姑） buddhist nun
  • 損 : Ⅰ動詞1 （減少） decrease; lose 2 （損害） harm; damage 3 [方言] （用尖刻的話挖苦人） speak sarcas...
  • 耗 : Ⅰ動1 （減損; 消耗） consume; cost 2 [方言] （拖延） waste time; dawdle Ⅱ名詞1 （壞的音信或消息） ...
  • 損耗 : 1. （損失消耗） loss; wear and tear; deterioration; waste 2. [商業] wastage; spoilage
  1. The cost of screen drag is appreciable in almost all installations.

    阻尼網的阻力損耗在幾乎所有的裝置中都是很大的。
  2. Through studying the working mechanism of the composing, the paper referred the bearing ' s analyzing model and designing flow. through shearing test of high damping rubber, the paper analyzes the influence of shearing shape, shearing strain range and inspiriting frequence on the characteristic parameters ( dynamic shear elastic module, dissipation engineering module, wasted gene ). according to the rule of equivalent energy, the paper gets the hysteretic curve of hdr ' s equivalent bilinear model and parameters ' calculating formula

    本論文通過對這種分離式減震支座各組成部分工作機理的研究，提出了該分離式減震支座整體的計算分析方法和設計流程；通過高阻尼橡膠剪切試驗，分析了高阻尼橡膠剪切面形狀、剪應變幅值、激勵頻率和試件高度對特徵參數（動態剪切彈性模量、耗能模量、損耗因子）的影響。
  3. The calculation formula for structure damping exhausting factor of combined pipe is denoted. structure exhausting factor of combined pipe treated by the damping material of sa - 3 is obtained with the different temperature and damping layer thickness

    推導出管道表面阻尼處理后復合管結構損耗因子的計算公式，並得出了sa - 3阻尼材料處理后，不同溫度、不同阻尼層厚度時復合管的結構損耗因子。
  4. Using the dynamic mechanical analyzer ( dma ), pdms / pma ipn was investigated at temperature of 5 - 180 c. the initiator, the component ratio, the type of pdms and the filler effected the damping properties. the result showed that the damping ability varied with the parameter and there was an optimal value. the excellent damping material in the papers was ipn, where tan man was 0. 735, and the damping functional temperature ranged with tan 8 > 0. 3 was 46 c. the micro - morphology and structure of pdms / pma ipn were characterized by two kinds of sem

    高分子阻尼材料的有效阻尼功能區是在ipn材料的t _ g區間內，而研究常溫條件下的阻尼性能更具有重要應用價值，運用動態熱機械分析（ dma ）儀對ipn阻尼材料進行表徵，在5 180內對其損耗因子（ tan ）進行研究，發現引發劑和交聯劑的用量、聚硅氧烷的用量和分子量等參數對ipn阻尼性能的影響較大，存在一個合理配比值，當pma與粘度為3300pa ? s的pdms之比（質量比）為1 . 17 ： 1 、交聯劑用量為1時， tan最大值為0 . 735 ，大於0 . 3的溫域差達到46 。
  5. The model analysis of the deployed beams were studied in both theory way and simulation way. the differences of the beams in different pressures were studied. investigations showed that the method of modeling for short and long rolled beams is doable ; the process of fold maybe lead so large displacement and stress that membrane is damaged at local areas, ration and material wrinkle generates,

    研究結果表明:本文提出的分別針對短、長捲曲折疊充氣管的建模方法是有效的;在充氣管展開過程中，充氣速度越大，展開的速度越快，但由於阻尼損耗，二者並非線性關系;充氣速度過大不利於結構展開過程的穩定性;充氣支撐管的氣壓越大其固有頻率越高，但影響效果很小。
分享友人
分享到 Line

分享到臉書