降液管長度 的英文怎麼說
中文拼音 [jiàngyèguǎnzhǎngdù]
降液管長度
英文
length of downcomer- 降 : 降動詞1. (投降) surrender; capitulate 2. (降伏) subdue; vanquish; tame
- 液 : 名詞(液體) liquid; fluid; juice
- 管 : Ⅰ名詞1 (管子) pipe; tube 2 (吹奏的樂器) wind musical instrument 3 (形狀似管的電器件) valve;...
- 長 : 長Ⅰ形容詞1 (年紀較大) older; elder; senior 2 (排行最大) eldest; oldest Ⅱ名詞(領導人) chief;...
- 度 : 度動詞[書面語] (推測; 估計) surmise; estimate
- 長度 : length; longitude; size; extent; footage
-
4. when the chloramines disinfection water is combined with the liquid chlorine disinfection water and reaches some stable ratio for a long time, the great reduction of the remained and total chlorines in the piped system will be obtained
4 、氯胺消毒處理后的水與液氯消毒后的水在管網中混合達到一定比例,長時間穩定接觸,將會出現管網水余氯、總氯大幅度降低的現象。The hemodynamic change induced by embolization of the cerebral arteriovenous malformation was analyzed using the water hammer principle. the highest pressure that can be reached when the water hammer phenomenon occurs was calculated. the acute instantaneous pressure rising may be an important factor leading to intracranial hemorrhage or swelling when the avm is embolized. it is shown that long feeding artery of avm will increase the possibility of direct water hammer, and high wall shear stress of feeding artery will increase the water hammer pressure. this suggests that such kind of avms should be embolized stepwise and the systemic pressure should be rationally reduced before embolization
以水擊原理分析了腦avm栓塞治療時血液動力學變化過程,計算了瞬時水擊壓力可能達到的最高值。瞬時增高的水擊壓力可能是avm栓塞時發生急性腦出血或腦腫脹的重要血液動力學因素。而avm供血動脈血管壁面切應力偏高和供血動脈過長可增加水擊的危險程度,提示對這類結構avm栓塞治療時應採取合理的降壓措施並盡可能分多次栓塞。The main results of this paper are as fellows f 1 ) illtroducing the ultrasonic technology to the rigid measurement, successful1y exploits the practical small intellectualized ultrasonic device of measuring rigidity by applying mechanical technology, electronic technology and computer science 2 ) reading clearcf displaying more various, applying more information, being easiest to accept by user because of adopting liquid crystal display ( lcd ) 3 ) theorizing the mathematical model between the signal of frequency and the rigid value on the device, possessing very importan practical significance 4 ) optimizing the every parts of the device, achieving the goals of lower wastage of energy, smaller, lighter and inexpensive 5 ) taking the measure to reduce the wastage of energy and adopting reasonable management in power supply for the device, making the device skimp more energy, prolonging the life - span of battery 6 ) utilizing the interface of rs - 232, discussing the communication between the ultrasonic device of measuring rigidity and computef, and also forecasting the foreground of advanced exploitation by user
本文工作的主要成果是: 1 )將超聲波技術引入零件表面硬度的檢測當中。應用機、電、計算機技術,研製成功較為實用的小型智能超聲波硬度檢測儀2 )採用lcd ( liquidcrystaldisplay )液晶顯示,使讀數更清晰、顯示多樣化、信息量多、易於為用戶接受3 )在理論上建立了該系統的頻率信號與硬度值的數學模型,具有非常重要的實踐意義4 )對各元器件進行優選,達到低能耗、體積小、重量輕、價格便宜等目的5 )採取措施降低整個系統的能耗並對系統的供電進行了合理的管理,使其進一步達到低能耗,延長了電池的使用壽命。 6 )利用rs - 232標準介面,討論了該超聲波智能硬度測量儀與系統機進行通訊以及用戶進行二次開發的前景
分享友人