除氣槽 的英文怎麼說
中文拼音 [chúqìcáo]
除氣槽
英文
degassing bath-
In addition to a longer nose, aerodynamic modifications feature kfir - style small nose side - strakes to prevent yaw departure at high aoa, a pair of fixed delta canards on the upper parts of the air intakes, dog - tooth outboard leading - edge extensions, and short fences replacing leading - edge slots
除了一個加長的機鼻外，氣動布局的修改包括：在機鼻兩則裝上可以防止在高攻角下脫離偏航的「幼獅」式小邊條，一對固定在進氣道的三角鴨翼，鋸齒型外翼前緣，和代替前緣翼槽的短翼刀。Commonly used preliminary treatment equipment includes bar screen, fine particle sieving, grit chamber, pre - aeration, grease well and scraping chamber, etc. domestic companies have the capability of manufacturing all equipment except fine sieves
常見的前處理設備有攔污柵、細篩機、沉砂設備、預曝氣池及除油井或油脂撇除槽等。國內前處理設備除了細篩篩網須國Emission is inducted evenly into the reactor, and effectively interact with recovery solvent sprayed down from top in the filler layer, then passes through the gas and liquid separation system to eliminate moisture for releasing clean air
廢氣由塔槽底部均勻進入洗滌塔，並在填充層與由上端噴流而下的洗滌液作有效的交換洗滌，再經由氣液分離系統去除水氣，清潔的空氣由出口排出。The technologies, including collecting the secondary fume by electrostatic precipitator on roof, restraining the open fume by dust inhibitor and treating the mobile fume by movable ventilation installation, are emphatically described. the adjustment and control of the gas flow and the pneumatic conveyance of the dust would be widely used in dust collecting system. as to the dust collector, low pressure pulse long bag filter and surface filtering technology would be a new technique in bag filter, and enlarged equipment would be the developing trend
著重講述了屋頂除塵器、抑塵劑、移動通風槽分別是二次煙塵治理、開放性揚塵抑制、移動塵源控制的新技術措施，風量調節與控制、氣力輸灰技術將在除塵系統中廣泛應用；在除塵設備方面，長袋低壓脈沖袋式除塵技術和「表面過濾」技術成為袋式除塵新技術，設備大型化將成為方向。This machine is a kind of radial riveting machine, the machine adopted the advanced radial technology, and its movement path likes the 11 pieces of plum blossom s shape, and using the screw pole to ascend and descend the work bench the head part is fixed, and the t - slot of bench can fix the clamping apparatus available, the center hole of bench and axis are coaxial, the one - way adjusting valve of liquid current is effectively controlled riveting speed
Jm12 - c是液壓類中重型徑向鉚接機，除應用有第五代徑向鉚接技術外，該機加長了鉚接行程，該項參數由普通機型的30mm加至60mm ，可滿足長行程深孔內鉚釘鉚接的要求。工作臺，並具有夾具梯形槽，工作臺中心孔徑與主軸軸線同軸，可用於夾具定位。氣路加裝雙向調節閥，有效控制鉚接速度。Based on simulation results which were satisfied, the effect of bubble diameter on entrainment concentration forcast result was analyzed. the bubble moving rule was found which includs the bubble is escaping upwards along the way, the diameter of the bubble is bigger, the velocity upwards is larger and the bladder remaining near channel bottom is smaller. to make best use of the function of the aerator, the demands of enough air entrainment quantity and suitable air bubble diameter are needed to be satisfied
根據計算結果，對水氣兩相流中氣泡尺寸對摻氣濃度預測結果的影響進行了分析，得到沿程氣泡不斷上逸，氣泡粒徑越大，其上逸速度越大，則留在渠底附近的氣泡越少的氣泡運動規律，提出了摻氣槽的設計，除滿足摻氣量外還應滿足摻氣粒徑要求的工程建議。Jm6tq is developed in foundation of jm6t, its adopted the advanced radial technology, the motion path of riveting - head resembles 11 pieces plum blossom s shapes. the ascend and descend of power head by screw pole and it can control the rough adjust effectively, and micro - adjust by screw cap of power head, the center hole of bench are coaxial with the spindle, and it put the holder available, and added the aerosol lubricate system in the air current it has the function of filter
Jm6tq氣動是在jm6t基礎上發展而來的氣動z中小型徑向臺式鉚接機，除應用有國際先進的11瓣梅花徑向鉚接技術外，該機應用有國際先進的徑向鉚接技術外，同時採用絲桿升降式工作頭，臺面具有夾具梯形槽，工作臺中心孔徑與主軸軸線同軸，可用於夾具定位。Ould have good flexibility and flexing fatigue - resistance performance ; it should be anti - aging, oil - resistant and wear - resistant ; on the inner side of the back there should be point angel grooves of appropriate sizes made not only to meet technical de mands but also for purpose to improve the anti - wear performance, meanwhile, part of the noises shall be eliminated due to the escaping of the detained air between the be
同步帶的背部用以粘結包覆抗拉元件，應有良好的柔韌性和耐曲撓疲勞性能，不易老化，耐油性好，耐磨損，在帶背的內表面開有適當大小的尖角凹槽，除因工藝要求外，還能改善帶的曲撓疲勞性能，同時在運轉過程中使帶與輪間的截流空氣逸出，以消除部分噪音。分享友人