陷凹狀態 的英文怎麼說

中文拼音 [xiànāozhuàngtài]
陷凹狀態 英文
etat lacunaire
  • 陷 : Ⅰ名詞1 （陷阱） pitfall; trap2 （缺點） defect; deficiency Ⅱ動詞1 （掉進） get stuck or bogged do...
  • 凹 : 凹名詞（凹陷的地方, 用於地名） low-lying area; depression （used in place names）
  • 狀 : Ⅰ名詞1 （形狀） form; shape 2 （情況） state; condition; situation; circumstances 3 （陳述事件或...
  • 態 : 名詞1. （形狀; 狀態） form; condition; appearance 2. [物理學] （物質結構的狀態或階段） state 3. [語言學] （一種語法范疇） voice
  • 狀態 : status; state; condition; state of affairs: （病的）危險狀態 critical condition; 戰爭狀態 state o...
  1. Thus wear and friction are reduced. 3 ) in the course of friction the nanometer cacos particles and cao particles can fill up the concave of the surface and even sink into substrate and fill in the worn position promptly

    （ 3 ）摩擦過程中納米碳酸鈣、納米氧化鈣粒子能填平摩擦表面低凹處甚至陷入基體中，並可及時填補損傷部位，具有自修復功能，使摩擦表面始終處于較為平整的狀態。
  2. Methods by use of certain its negative pressure, we designed a tool for inverted nipple lifting to suck out it to its normal position

    方法製作乳頭凹陷隆起器，用負壓吸引原理，將乳頭吸引出並維持到正常狀態。
  3. Objective because of the operative method for congenital inverted nipples often brings some serious complications, we investigated the non - operative procedure for recontour of inverted nipple

    目的由於手術治療先天性乳頭凹陷常有些嚴重並發癥，故研究利用非手術負壓吸引療法，將凹陷乳頭吸出，並維持到正常狀態。
  4. This control cabinet can control every point temperature in the hot runner, and keep a plastic flow at an optimum condition so that it is possible to avoid such defects as hollow and contraction cavity from lacking in supply, and to save materials and labor and reduce production costs at the same time. compared with ordinary, such hot runner will shorten the time of mould removal, carry out full - automatic ordinary, such hot runner will shorten the time of mould removal, carry out full automatic operation more easily, reduce the distance of mould - opening and the stroke of mould - closing

    使用本控制櫃能精確控制流道中各點溫度，使塑料流動達到最佳狀態，這樣能克服製件因補料不足而產生凹陷，縮孔等缺陷，同時節省了材料和人力，降低生產成本，與普通流道比脫模周期短，易實現全自動操作，可以縮短開模距與合模行程，縮短成型周期，可以成型較長製品。
  5. Researches show there are many types of strata pressure, super pressure in certain depth below the bottom of the jurassic stratum, and also overpressure in the whole jurassic stratum in central and southern of mosuowan salient

    研究表明該地區地層壓力類型豐富，侏羅系底部及以下地層在凹陷內一定深度以下普遍發育高壓，在莫索灣凸起的中南部侏羅系則整體處于超壓狀態。
  6. The following are main conclusion and recognition : firstly, basing on the study mudstone compaction, drawing a conclusion is that the profile and plane feature of palaeo - pressure in y3, on profile, the pressure ranged from 5mpa to 10mpa in the southern area of wuerxun. usually, high pressure was in n1 or t. in the northern area of wuerxun, high pressure almost reached to 5mpa, high pressure usually was in d1 or n2

    在海拉爾盆地研究中，以此為切入點，通過大量實際工作，取得了如下初步的研究結論和認識：首先，通過壓實研究，得出了地層在最大埋深狀態下（伊敏組末） ，古壓力的縱橫向分佈特徵：縱向上，烏爾遜凹陷南部異常壓力幅度在5 10mpa之間，最大異常壓力一般出現在南屯組一段或銅缽廟組。
分享友人
分享到 Line

分享到臉書