離合桿 的英文怎麼說

中文拼音 [lígěgǎn]
離合桿 英文
ausrueckhebel
  • 離 : Ⅰ動詞1 （離開） leave; part from; be away from; separate 2 （背離） go against 3 （缺少） dispens...
  • 合 : 合量詞（容量單位） ge, a unit of dry measure for grain （=1 decilitre）
  • 桿 : 桿名詞（桿子） pole; staff
  1. Clutch drive rings for shell end mill arbors

    空心端銑刀刀桿用離合器驅動環
  2. Clutch pedal shaft lever

    離合器踏板軸桿
  3. Clutch operating lever

    離合操作桿
  4. There is no clutch, gearing, oil changes, smog check, pistons, rings, valves, crankshaft, flywheel, rods, wrist pins, etc., etc

    沒有離合器，傳動裝置，機油變化，尾氣檢查，活塞，活塞環，閥門，曲軸，飛輪，連桿，肘節銷，等等。
  5. Bearing release lever

    離合器推力軸承放鬆杠桿
  6. When the torque was being increased, this equipment would quickly measure the data of torque, making electromagnetic clutch opened and feed stopped, so that the driller and drilling bar would be protected

    當扭矩增大時，可以快速檢測扭矩參數，並控制離合器迅速脫開，停止進給，保護鉆頭鉆桿。
  7. The problem of torque increase and drill fracture during the process of deep well drilling was analyzed, and a safety protection and control technique was introduced, where a torque sensor was fixed between drilling bar and motor axis, while an electromagnetic clutch was fixed in the transmission chain of feed system

    摘要對深孔鉆削過程中出現扭矩增大及折斷鉆頭鉆桿問題進行了分析，介紹了一種鉆桿主軸與電機軸的連接中安裝扭矩傳感器，進給系統的傳動鏈中安裝電磁離合器的深孔鉆削安全保護與控制技術。
  8. Clutch release arm rod

    離合器放鬆臂桿
  9. Cutterbar clutch lever

    切割器傳動離合器操縱桿
  10. Clutch toggle lever strut

    離合器肘節桿支柱
  11. Clutch toggle lever

    離合器肘節桿
  12. Clutch release lever spring

    離合器放鬆桿彈簧
  13. Harmonized blank detail specification for lead screw actuated non - wirewound preset potentiometers - square form, container sealed, actuating device insulated from resistive element, slipping clutch at each end of travel, rigid terminations - assessment level s

    導螺桿傳動非線繞預調電位器協調空白詳細規范.正方形的容器密閉的與電阻元件絕緣的驅動裝置每個行程終止的滑動離合器剛性終端.評定級別s
  14. After designing oil ditches on the surface of its arc - block, increase friction factor and make sure self - lock which solves above problem. do qualitative analysis to lower pair and one - way overrunning clutch and inner star - wheel - roller overrunning clutch by using self - made lever loader. the experiment shows : on the same condition, the deformation of new overrunning clutch ’ s surface contact with lower pair is smaller than the deformation of roller overrunning clutch ’ s line contact with higher pair and new overrunning clutch ’ s skid angle is smaller

    對低副單向超越離合器的部件進行了加工製造，在超越離合器弧塊表面創新設計加工排油溝，增大摩擦系數，保證實現自鎖，解決了很多離合器工作過程中容易出現無法自鎖的問題;對低副單向超越離合器和內星輪滾柱超越離合器用自製杠桿加載器做了定性分析，實驗表明:相同條件下，新型離合器低副面接觸比滾柱離合器高副線接觸變形小、溜滑角小。
  15. Clutch operating shaft lever

    離合器操縱軸桿
  16. Clutch foot lever

    離合器腳踏桿
  17. Clutch foot lever bracket

    離合器踏桿座
  18. China spring factory, founded in 1937, is the largest spring manufacturer in china. it mainly produces automotive suspension spring, engine valve spring, stabilizer bar, die spring, shaped spring, dise spring, clutch spring

    中國彈簧廠始建於1937年，是中國規模最大的彈簧製造企業，主要生產汽車懸架彈簧、發動機氣門彈簧、穩定桿以及模具彈簧、異型彈簧、碟形彈簧、離合器彈簧、超大型彈簧、各類彈性沖壓件和其他精密螺旋彈簧。
  19. Clutch installation and release linkage requirements for truck and bus applications

    卡車和客車的離合器裝置和復位桿要求
  20. Detail specification for lead - screw actuated wirewound or non - wirewound preset potentiometers - rectangular and square forms, container sealed, actuating device insulated from resistive element, slipping clutch at each end of travel - full assessment level

    導桿驅動線繞或非線繞預調電位計詳細規范.長方形和正方形密封容器與電阻元件絕緣的驅動裝置每個行程終止的滑動離合器.全面評估級
分享友人
分享到 Line

分享到臉書