離心泵葉輪 的英文怎麼說

中文拼音 [líxīnbèngyèlún]
離心泵葉輪 英文
centrifugal pumrunner
  • 離 : Ⅰ動詞1 （離開） leave; part from; be away from; separate 2 （背離） go against 3 （缺少） dispens...
  • 泵 : 名詞（吸入和排出流體的機械） pump
  • 輪 : Ⅰ名1 （輪子） wheel 2 （像輪子的東西） wheel like object; ring; disc 3 （輪船） steamer; steamboa...
  • 離心 : 1 （不是一條心） be at odds with the community or the leadership2 （離開中心） centrifugal; eccen...
  1. Ruichi " brandmagnetic pump is mainly made up of pumpbody, gears, magnetic combined bearing equiptment isolation cover, motor and so on. gear wheels joined with the inner magnetic steel are fixed in a hermetically sealed chamber which is made up of pumpbody and isolation cover. the motor powers the outer magnetic steel, the outer magnetic steel power the inner steel. gear sheels are made to try turn. thus dynamic hermetis seal is replaced by a static hermetic seal to get the result of importing medium wihtout leakages

    「瑞馳牌」磁力泵泵體主件是由驅動和從動永磁場鋼杯組成磁性聯軸節外磁鋼和電動機相聯為主動件內磁鋼和葉輪相聯為被動件當電機啟動后通過磁力藕合驅動葉輪同步工作泵的結構要點以靜密封取代動密封使泵的過流部件完全處於密封狀態從而保證了介質和外界隔絕徹底解決了離心泵機械密封一直解決不了的跑、冒、滴、漏之弊病。
  2. Impeller diameter maximum approach for deep well pumps

    深井離心泵葉輪極大直徑設計法
  3. It is in the light of iso international criterion to design and make, pumpbody adopt metalline crust pad fluorine plastics inside, impeller and pump - cover all adopt metal embed part wrap fluorine plastics alloy outside to press. it has ratio of very high capability and price. its the most diffusely apply of resisting causticity centrifugal pumps at chemical engineering profession at present

    按國際標準設計製造，泵體採用金屬外殼內襯氟塑料f46 ，葉輪及泵蓋均採用金屬嵌件外包氟塑料合金模壓成型，具有很高的性能價格比，是目前化工行業應用最為廣泛的防腐離心泵。
  4. It adopts reynolds time - average n - s equation and k - ? turbulence model to calculate the inner 3 - d viscid turbulence flow of centrifugal pump. in the unstructured grid, the governing equations are discretized with finite volume method based on finite element method. then the pressure correction method is used to carry out numerical calculation

    而後採用基於雷諾時均n - s方程與標準-湍流模型來求解離心泵葉輪內三維粘性紊流，在非結構化網格中，採用基於有限元的有限體積法對方程進行離散，用壓力校正法進行數值求解。
  5. The creative points of the thesis are as follows : （ 1 ） the thesis establishes turbulence boundary layer equation that contains centrifugal force in flow field of two - dimension boundary layer of centrifugal pump and gives its solution

    本文創新之處是： （ 1 ）在離心泵葉輪二維邊界層流場內，建立了包含離心力的湍流邊界層方程並給出了近似解。
  6. Discussion of cavitation flow in impeller of centrifugal pump

    離心泵葉輪內汽蝕發生的理論探討
  7. Study on 3d solid modelling for centrifugal pump blade of impeller

    離心泵葉輪扭曲葉片參數化實體造型方法探討
  8. Numerical simulation of dense liquid - solid two - phase turbulent flow in a centrifugal pump impeller

    離心泵葉輪內密相液固兩相湍流的數值模擬
  9. The author designed an unshrouded centrifugal impeller, set in the transparent centrifugal pump

    本文中設計了半開式離心泵葉輪，安裝在清水透明離心泵實驗裝置中。
  10. In this paper, an organic combination of surface molding and numerical calculation is applied to optimization design for centrifugal pump impellers

    本文將曲面造型與數值計算有機的結合在一起應用到離心泵葉輪的優化設計中。
  11. Li hai ? feng, mu zhong ? bo, wu yu ? lin. the three dimensional turbulent flow simulation in semi ? open centrifugal impeller [ j ]. pump technology, 2001 ( 1 ) : 915

    李海峰，穆忠波，吳玉林.半開式離心泵葉輪內部三維紊流的數值模擬[ j ] .水泵技術， 2001 （ 1 ） : 915
  12. The performance curve was acquired at the pump operating speed of 1200rpm. piv was applied to the measurements of the flow fields in the unshrouded centrifugal pump. during the measurements, three operation points of the pump were taken

    本文應用piv測試技術，分別在1 . 4 、 1 . 0和0 . 6倍最優流量的工況下，對半開式離心泵葉輪內部流場進行實驗研究。
  13. From then on, many domestic scholars have made much research on the numeric simulation of the centrifugal pump inner 3d turbulent, and they have made some progress, which were yet short of enough validation through experiment

    迄今為止，國內許多學者已經對離心泵葉輪內部三維紊流數值模擬進行了研究，也取得了一些成果，但並不理想，也缺少實驗驗證。
  14. The method takes advantage of bezier curve to work out a set of blade profiles of centrifugal pump, using thickening law to thicken the profiles. then the pressure and suction lines of the blade can be obtained. it takes advantage of bezier surface to create pressure and suction surface and makes use of mdt software to create the three - dimensional blade entity

    首先採用速度系數法計算得到離心泵葉輪的基本參數，再由b zier曲線生成一組葉輪葉片型線，按照加厚原理對型線進行加厚，得到正背葉片線，再採用張量積b zier曲面生成葉片正背面，由mdt進行三維實體造型得到葉片，從而得到流場計算區域的模型。
  15. With the phenomena of dropping flow, backflow and secondary flow effected by circulation and surface curvature, the centrifugal pump ' s inner flow is very complicated 3d flow. therefore, the centrifugal pump inner flow is one of the difficult problems both in testing research and numeric computation

    離心泵葉輪的內部流動是很復雜的三維紊流流動，同時由於受旋轉和葉片表面曲率的影響還拌有脫流、迴流及二次流的現象，是流體工程中較難的試驗研究和數值計算問題之一。
  16. Firstly, based on n - s equation, the momentum differential equation （ contained centrifugal force ） is derived by simplification in boundary layer and then integrates the differential equation over the thickness of the boundary layer, the momentum integral equation is deduced. the dimensionless centrifugal factor is introduced, then the solution of the momentum integral equation is obtained. the dimensionless group is introduced to determined separation of boundary layer

    本文首先根據粘性流體力學的一般方程，通過在邊界層內進行量級比較，在所限定的范圍內得到了含有離心力的邊界層動量微分方程並給出其滿足的邊界條件，然後對該微分方程在邊界層內積分得到離心泵葉輪邊界層動量積分方程，在求解過程中引入了無量綱離心因子，並作了相應合理的假設，得出積分方程解的一般表達式，並引入以邊界層動量損失厚度為主要特徵量的無量綱參數對邊界層分離進行評價。
  17. By adopting surface molding to obtain solving region and then carrying out numerical calculation and analysis of flow field in centrifugal pump, accurate remodification information is obtained and optimized impellers which have excellent fluid dynamics capacity is schemed out

    採用曲面造型得到計算區域，通過對離心泵葉輪內部流場的數值計算與分析，為離心泵優化設計提供準確的修改意見，設計出水力性能優異的葉輪。
  18. In this paper, based on the navier - stokes equation and the k - turbulent model, the numerical simulation of the 3d turbulent flow in a centrifugal impeller, of which specific speed is 93. the distribution of the velocity and pressure in the blade - to - blade passage are presented at the design and off - design operating conditions. the simulation results were verifiable with the results measured by piv

    本文基於n ? s方程和標準的k ?雙方程紊流模型，採用商用cfx - tascflow計算軟體對一離心泵葉輪模型進行了葉輪內部三維紊流數值模擬，得到了三個典型工況下、從輪轂到前蓋板每一個斷面上的速度和壓力分佈。
  19. Based on the theory of boundary layer and analysis of the velocity field of main flow, the thesis also derives the vane shape equation. in the equation, （ angle of pump vane ） is variable parameter, （ velocity coefficient ） is introduced as medium factor, which connects the theory of boundary layer with the eular theory. it provides a valuable reference for the designation of vane of pump

    基於離心泵葉片邊界層理論和對主流區速度場的分析，給出了離心泵葉片型線參數方程，它以葉片角為變參數，引入速度系數作為中間因子，將邊界層理論和歐拉理論聯系起來，並在離心泵葉輪的設計過程中統一起來，能夠在設計中就根據實際的需要防止或控制過流表面的邊界層的分離。
  20. Dr. zhu yucai first presented the theory of boundary layer of centrifugal pump and derived the vane shape equation. based on the theory and analysis of references abroad and home on centrifugal pump, the thesis creates a mathematic model of turbulent boundary layer of centrifugal pump

    朱玉才博士首次提出了離心泵邊界層理論並給出了葉片型線方程，本文就是基於朱玉才博士研究工作的基礎上，通過大量分析國內外有關文獻，建立離心泵葉輪湍流邊界層的數學模型。
分享友人
分享到 Line

分享到臉書