離隙角 的英文怎麼說
中文拼音 [líxìjiǎo]
離隙角
英文
angle of relief-
Both the complicatedness varieties trees, the thick liquid material that the material differs greatly and the remaining leftover bits after wood processing, wood shaving, sawdust, sub thick liquid, cotton stalk, hemp stalk, bush, crudefiber crop, rice wheatgrass, reed, crudefiber crop, many kinds of goods thick liquid board, wasted paper, bagasse, agrimony etc. canbe fasten separated into the good fibre with higher velocity and proper to rub a block of interval
高濃磨對漿料的適用范圍較廣，無論是樹種復雜，材料差異較大的漿料，還是木材加工后剩餘的邊角料，以及蝕花、鋸屑、節子漿、棉稈、麻稈、灌木、枝椏材、稻麥草、芳菲、麻類多種商品漿板、廢紙、甘蔗渣、龍須草等，都能夠以其料高的旋線速成度及適當磨片間隙分離成優質纖維。Analyze item by item the position of unintact cycle, the running clearance of unintact cycle, locking - deform, datum dimension regulating, repeatly install, power voltage wave and marking running etc. at the same time, we give the calculating formula to calculating the running marking random error, and use it to calculate the system error of big diameter measure instrument - - datum dimension frame error, gyro - wheel diameter error, error caused by circumstance temperature, error caused by backing distance, angle error, delay error of data collecting circuit, lathe main shaft running error, workpiece install partial error
對不完整圓的位置、不完整圓的轉動間隙、鎖緊變形、基準尺調整、重復安裝、電源電壓波動、標記轉動等隨機誤差進行了逐項分析，並給出轉動標記隨機誤差的計算公式。對大直徑測量儀的系統誤差?基準尺尺架誤差、滾輪直徑誤差、環境溫度引起的誤差、後退距離引起的誤差、角度誤差、數據採集電路延時誤差、車床主軸回轉誤差、工件安裝偏心誤差分別進行了計算，最後對誤差進行合成。7, 0. 9cm to 1. 5cm place to the wall start to nail the first floor, that 0. 9cm to 1. 5cm the expansion and contraction crevice can be covered up with gangway and the angle line after the floor finished
7距離墻邊0 . 9至1 . 5處開始面釘第一片地板，此0 . 9至1 . 5的伸縮空隙于地板完工後可用跳腳板或角線遮掩。Firstly in this part, computer simulation methodology based on the baecher model for generating network of discrete fractures was presented, which includes the follow details : probability distributions of fracture density, orientation, trace length, size, and aperture and estimation of their statistical parameters ; stochastic models of fracture network ; monte - carlo ' s simulation method ; numerical simulation procedure and technicality. then, boundary element method was used to calculate flow through the generated fractured network. assuming single fracture as a two - dimension inexpressible isotropic porous media, boundary element method equations for flow in single fracture and then in fracture network were derived using the weighted residual method
給出了離散裂隙網路模型所依據的基本假定；發展了基於baecher模型的離散裂隙網路計算機隨機生成技術：詳細地推導了單裂隙滲流和多裂隙相交網路滲流的邊界單元法公式，發展了離散裂隙網路中穩態滲流的邊界元數值技術，並且討論了相關的具體數值技術細節，如角點的處理方法，單元的自動剖分等：描述了混合邊界元?管流模擬方法及其數值實現；研究了裂隙網路的簡化方法，並針對裂隙網路邊界元法的特點提出了一種改進的分塊三角分解法。Aqueous fluid volume and [ c1 ~ j were assayed in samples withdrawn by micropipettes. intraocular pressure ( top ), pressure - dependent outflow, and anterior chamber compliance were determined from pressure measurements in response to pulsed and continuous fluid infusions into the anterior chamber using micropipettes. result : in wildtype mice ( gdi genetic background, age 4 - 6 weeks ), iop was 16. 0 ? 0. 4 mmhg, aqueous fluid volume was 7. 2 ? 0. 3 ul, aqueous fluid production was 3. 6 ? 0. 2 ul / hr, aqueous fluid outflow was 0. 36 ? 0. 06 ul / hr / mmhg, and anterior chamber compliance was 0. 036 ? 0. 006 ul / mmhg ( mean ? se, 8 - 10 eyes )
實驗方法包括：將熒光物質用電離子滲透的方法穿透角膜導入活體小鼠的前房中，然後應用共聚焦顯微鏡根據熒光強度變化測量房水生成率；通過顯微注射針吸取房水檢測房水容積和氯離子濃度；顯微玻璃管刺入前房測量眼內壓，並將生理鹽水分別以連續和脈沖兩種方式注入前房，測量房水間隙的順應性和房水排出與眼內壓的相關性。分享友人