電位自調器 的英文怎麼說

中文拼音 [diànwèizìdiàoqì]
電位自調器 英文
potentiostat
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 位 : Ⅰ名詞1 （所在或所佔的地方） place; location 2 （職位; 地位） position; post; status 3 （特指皇帝...
  • 自 : Ⅰ代詞（自己） self; oneself; one s own Ⅱ副詞（自然;當然） certainly; of course; naturally; willin...
  • 調 : Ⅰ動詞1 （配合得均勻合適） harmonize; suit well; fit in perfectly 2 （使配合得均勻合適） mix; adju...
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  1. Pre - data gathering module achieves the collection and communication of sixteen - route temperature signal. speed measuring and controlling module realizes the control of refolw soldering transfer speed by manipulating transducer. on - off outputting module fulfills calefaction control of calefaction tube by solid state relay. above position operator software programs by delphi, and realizes pid parameter automatic timing and no - oversnooting temperature control. software has friendly interface, convenient operation, complete functions

    前置數據採集模塊完成16路溫度信號的採集和通訊；速度測量模塊與速度控制模塊通過控制變頻器來調節迴流焊的傳輸速度；開關量輸出模塊通過固態繼電器對加熱管進行控制；上位機軟體採用delphi編程，實現了pid參數自整定以及無超調的溫度控制。
  2. The central control room of the branch is located in the bank of communications plaza in the lujiazui, shanghai, which adopts the xbrother developed professional security and facility control system which monitors and controls 10 subsystems in the central control room, including : the ups control system ; the coulometer control system ; the leaking control system ; the temperature and humidity control system ; the air conditioning control system ; the video surveillance system ; the sensor of in out water temperature control system ; the access control system ; the switch control system and ; the fire alarm system

    交通銀行機房位於上海浦東新區陸家嘴金融中心的交銀金融大廈內，其機房監控系統採用我司自主研製的專業機房監控系統。對機房內的ups監控系統電量儀監測系統漏水監控系統溫濕度監控系統空調監控系統視頻監控系統進出水溫傳感器監測系統門禁監控系統開關狀態監控系統消防監控系統等10個子系統進行集中監控，對所有的設備和系統進行工作狀態運行參數報警處理等監視和管理。
  3. The third, after theoretically analyzing, the following practicable methods are put forward : 1 ) automatically pick - up the synchronous information by analyzing the spectrum of intercepted video - leaking information ; 2 ) realizing the phase lock and the electronic image stabilization by integral - projection and differential - positioning ; 3 ) improving the effect of accumulation mean filter and the pectination filter by using electronic image stabilization ; 4 ) automatically adjusting image acquisition parameters by detecting the image entropy, therefore the quality acquired image is improved ; 5 ) to realize the quantitative test of a leaking extent, a standard test picture was designed. finally, a proto type for leaking information processing based on our techniques mentioned above and the virtual instrument principle was designed and tested

    在理論分析的基礎上，提出了以下的實用技術： 1 ）用譜分析方法從截獲的信息中自動提取同步信息； 2 ）用積分投影、微分定位的方法進行相位檢測，實現可靠的鎖相和電子穩像； 3 ）將電子穩像技術用於重加濾波和梳狀濾波的濾波方法，改進了濾波效果； 4 ）通過檢測圖像信息熵實現圖像採集參數的自動調整，改進了圖像採集的質量； 5 ）設計了用於儀器定標的標準測試圖，可以對泄漏信息進行定量檢測。
  4. It integrates the functions of servo amplifier, dynamic operator, position transmitter and remote communication. many new functions have added to its original ones, such as the real - time logical judgment, malfunctions self - diagnosis, alarm & protection, led display, on - line setting and adjustment of functional parameter and position transmitter, power - absence data auto - protection, watchdog system protection, and the long - range communication with pc

    系統集伺服放大器、電動操作器、位置發送器及遠程網路式通信功能於一體，在保留對應部分原有功能的同時，還新增了邏輯實時判斷、故障實時監控、 led動態顯示數據、功能參數設置、掉電數據自保護、 「看門狗」電路保護、位置發送器在線調節、與遠程工控機數據通信等眾多功能。
  5. Substation automatization system often uses communication controller to carry out communication with field computer and remote computer

    變電站自動化系統中常採用通信控制器負責與上位機及調度中心的通信。
  6. Fixed camera fastening its interior is loaded with an electric motor, on installs the good camera after the level to be possible to adjust the angle which the camera deals with, after achieved the best surveillance effect may accept the automatic control regulator by the electric motor the signal precisely to move the localization in under the control signal function, the camera already may automatically carry on the horizontal scanning to monitor the region, also may in under the monitoring center attendant s operation the moving surveillance object input voltage : ac 24v 50 60hz, 110v 60hz, 220v 50 60hz external dimensions : 119mm 115mm is high the weight : 0. 9kg material : abs high strength casts takes shape the degrees rotation : level biggest : 350, vertical 90 may adjust the velocity of whirl : 5 second 4 seconds revolve the spacing : exterior spacing card tunable load : 7kg function input plug : 1

    Kl - 306室內水平雲臺是安裝，固定攝像機的支撐設備.它內部裝有一電動機，在水平雲臺上安裝好攝像機后可調整攝像機俯仰的角度，達到最好的監視效果后可由電動機接受來自控制器的信號精確地運行定位.在控制信號的作用下，雲臺攝像機既可自動進行水平掃描監視區域，也可在監控中心值班人員的操縱下跟蹤監視對象
  7. It can call the police at the moment danger, and provide identity and detecting and monitor of temperature and humidity, and control action of gate - lock, air - conditions and other appliance

    具有對住宅各要害部位進行多種監測報警服務功能，集防盜、防劫、防火、防水、防燃氣泄漏等功能於一體，一遇不測即刻自動報警；提供門禁身份識別及溫濕度檢測和顯示，同時可控制門鎖動作，空調等家用電器。
  8. The way that two kinds of different potentiometer feeding back the blade gap value in adjusting mechanism of cnc shear have been introduced

    摘要介紹了數控剪板機刀片間隙自動調整機構中兩種不同電位器反饋刀片間隙值的方式。
  9. Abstract : it introduces the principle of graphite electrode abrading tool and develops the software and hardware of nc machine. this can detect the position of platform feed with great inertial - mass through photoelectrical encoder, the vibration magnitude of translation worktable with eddy transducer. based on these the machine parameters can be automatically regulate, and the grinding process is smooth

    文摘:介紹了石墨電極研磨成形機的原理和數控軟、硬體系統的研製開發；用光電編碼器實現了大質量進給滑臺的位置檢測；並用電渦流傳感器檢測平動臺振動量，進而實現了機器參數的自動調整，從而保證了石墨電極研磨成形機研磨加工的順利進行。
  10. Along with the ecological and energy - saving trend of construction development, diangong solar applies light - heat conversion technique to realize the integrated air conditioning system of water heating. heating and refrigerating. it co centralizes large area of solar heat collectors to heat water, uspplying families and units with consistent water supply. in winter, it uses the solar heated water to realize floor heating or fan heating, in summer, the heated water is used to refrigerate by the high - efficiency hot water refrigerating set solely developed by diangong. besides, the systemis equipped with assisting resources to form an integrated air conditioning system, which is efficient, safe, environmental, energy - saving and economic. by it, people can enjoy a natural and healthy life at home

    電工太陽能順應生態節能建築發展潮流，以太陽能光熱轉化技術實現熱水/供暖/制準予一體化空調系統工程應用，採用大面積太陽能集熱器採集中高溫熱水，為家庭或單位用記提供全方位熱水供應，在冬季利用太陽能熱水進行地板或風機供暖，解決冬季取暖問題，在夏季利用太陽能熱水，通過電工獨立開發的商效能熱水製冷機組進行製冷，集成太陽能一體化空調系統，系統配備輔助能源，全天候自動運行，高效，安全、環保、節能、經濟，在家中享受陽光自然的舒適健康生活。
  11. Based on remaining the dismantling and loading, we make full of the equipped instrument, and fall the whole cycle into three modules : speed - adjusting module, pressure module and multi - execution instrument module. we must compile the related plc control program and pc control program, and redesign the control cabinet and re - fix the electric cycle. we complete the auto - control of the hydraulic experiment table through the loading and recapitulate debugging

    在保留其元件可裝拆性的基礎上，我們充分利用現有液壓實驗臺的液壓元件，對其基本迴路進行重新組合，分為調速、壓力和多執行元件控制迴路三個模塊，並編制可編程式控制制器程序和上位機數據採集程序控制迴路動作，重新設計該實驗臺的電氣控制櫃，並進行現場接線和安裝調試，實現所有教學必須實驗迴路的自動控制。
  12. In this thesis, based on a digital signal processor tms320f240, a controller for pmsm is researched an designed. we analyzes the mathematics model of pmsm, researchs vector control of pmsm and space vector pwm, discusses the controller of position, speed and current, designs the mrfas position controller, pid speed controller and pid current controller, sets up pmsm ac servo control system, designs dsp controller, and develop the corresponding sofeware. at last, the designed controller is simulated under matlab / simulink, and the results are gived

    分析了水磁同步電機的數學模型，研究了永磁同步電機的矢量控制方法和空間矢量脈寬調制原理，討論了位置環、速度環和電流環的控制方法，設計了模型參考模糊自適應位置控制器、 pi速度器和pi電流控制器，組建了永磁同步電機交流伺服控制系統，設計dsp控制器，並開發了相應的軟體。最後在matlab simulink環境下對系統進行了動態模擬，並給出了模擬結果。
  13. The system is based on chopper constant current drive technique, according to the top level design idea, adopting advanced specical subdivision control integrate circuit and powerful function 80c196kc to organize the system frame, desiging the minimum system of single - chip microcomputer, multifunction i / o interface circuit, relay switch circuit, keyboard and display circuit, multifunction digital setting interface circuit and so on, utilizing the hso and hsi interface circuit which are owned by this single - chip microcomputer exclusively and its powerful command system to realize dual - degree switch control, automation orientation, automatically searching zero position, locking machine when stopping, frequency to set digitally, automatically adjusting speed through changing frequency, swithing subdivision or squarewave control, on the basis of above, the system also have the function of running according to the setting steps and the frequency, voltage and current to display through the led, etc

    系統基於斬波恆流驅動技術，按照頂層設計思想，採用先進的專用細分控制電路和功能強大的80c196kc單片機來組建系統構架，設計了單片機最小系統、多功能i o介面電路、繼電器切換電路、鍵盤顯示電路和多功能數字設定介面電路等，利用該單片機獨有的hso和hsi介面及其強大的指令系統，實現了雙余度混合式步進電動機的余度切換控制、自動定位、零位自動搜索、停機鎖定、數字化頻率設定、自動調頻變速控制、細分方波切換控制，在此基礎上，該系統還設有按預置步運行、 led頻率電壓相電流顯示等功能。
  14. It is composed of magnetic pulse sensor and control components, and is a built - in part inside distributor. it detects engine cranking position signal and cylinder signal via sensor, followed by treatment by control unit, thus controlling the on off of the current of control ignition coil to achieve the purpose of ignition. it has a function of auto closing regulation

    該型產品是為微車無觸點點火系統而研發的，它由磁脈沖傳感器和控制組件構成，內置於分電器內，通過傳感器檢測發動機曲軸位置信號汽缸信號，然後經控制組件處理，控制點火線圈中電流的通斷，從而達到點火目的，具有閉合角自動調整等功能。
  15. It is composed of magnetic pulse sensor and control components, and is a built - in part inside distributor. it detects engine cranking position signal and cylinder signal via sensor, followed by treatment by control unit, thus controlling the onoff of the current of control ignition coil to achieve the purpose of ignition. it has a function of auto closing regulation

    該型產品是為微車無觸點點火系統而研發的，它由磁脈沖傳感器和控制組件構成，內置於分電器內，通過傳感器檢測發動機曲軸位置信號、汽缸信號，然後經控制組件處理，控制點火線圈中電流的通斷，從而達到點火目的，具有閉合角自動調整等功能。
  16. Due to the component of natural gas is very complex in different zone of our country, the product has taked on special design, it set up moore component factor of thirteen kinds, which offer user to select and setup, so as to satisfy measurement for contains various component natural gas, at the same time established many take - pressure way in order to suit to different measure device, and have automatic calculate and display super - compression factor function

    A q型操作器輸出svout ： 010ma 420ma 05v 15v信號，可直接驅動執行機構變頻器或再由伺服放大器去驅動電動調節閥門或由電氣轉換器和閥門定位器去驅動氣動薄膜閥。操作器處于自動工作狀態時，其信號輸入svin和操作輸出信號相當於是直通的。以實現dcs系統或調節器對執行機構的自動控制。
  17. The thesis finished a sample instrument used in measurement node. it is based on 8 - bit micro controller unit and has smart functions including auto calibration, auto scale change and auto balance of whetstone bridge. the data can be processed, stored, transferred and displayed in the sample device

    本文完成了測試系統中基於16位微處理器的網關的硬體架構和軟體實時多任務內核的設計；研製了基於8位微處理器的具有自校正、自動量程轉換及測試電橋的自動調平功能的測試節點樣機；實現了測試節點的數據處理、存儲、顯示和傳送；繪制並編寫了測試節點的硬體電路圖和軟體源程序。
  18. Specification for electrically operated automatic gas shut - off valves fitted with throughput adjusters, proof of closure switches, closed position indicator switches or gas flow control

    裝有流量調節器閉路開關檢驗閉合位置指示開關或氣流量控制器電動式氣體自動關閉閥規范
  19. In the design of real - time control system, the paper takes three - phase full - bridge mosfet inverter as the real - time control main circuit, and adopts a control scheme with 120 ? switching mode combined with half - bridge pulse width modulation ( pwm ), which would avoid straightthrough short of a certain bridge. phase current is detected by single current sensor ; three - phase position signals generated by position sensors could not only supply commutation information for inverter, but also be used for speed detecting based on signals " period measurement, which makes the speed sensor unnecessary. the whole control system adopts speed and current dual closed - loop control strategy in order to construct a high performance rare - earth permanent magnetic brushless dc motor ( repm bldcm ) full - digital real - time control system

    在實時控制系統的設計中，本文以三相全橋mosfet逆變電路作為實時控制主電路，採用120導通方式結合半橋pwm調制的控制方案，從而有效地避免了橋臂的直通短路；本文用單電流傳感器實現對相電流的檢測，來自位置傳感器的三相位置信號不僅為逆變電路提供換相信息，而且也用於基於信號周期測量的轉速檢測，這樣就省去了速度傳感器；系統採用的是速度、電流雙閉環控制策略，力求構建高性能的稀土永磁無刷直流電動機全數字實時控制系統。
  20. The article in lead - zinc mineral tailing transmission pumps electric motors automatic control system of huang - shaping, for example, a detailed account of the system frequency conversion governor, ultrasound liquid position controller design models, debugging points and parameters set methods, and energy saving effect of a careful analysis

    摘要文章以黃沙坪鉛鋅礦尾礦輸送泵電動機自動控制系統為實例，詳細介紹了系統中變頻調速器、超聲波液位控制器的設計選型、調試要點和參數設定方法，並對節能效果進行了認真分析。
分享友人
分享到 Line

分享到臉書