電弧區域 的英文怎麼說
中文拼音 [diànhúqūyù]
電弧區域
英文
arc zone-
Electrical field stress at the icicle tips is even stronger. at these areas, if the electric field across air gaps is high enough, corona discharges are initiated. this can lead to the development of local arcs across the air gaps causing a substantial increase in leakage current and a concomitant melting of ice
空氣間隙的存在使覆冰絕緣子表面的電場分佈發生了明顯畸變，間隙上承受了非常高的電壓，這使得冰凌尖端的電場變得相當強，一旦電場達到了電暈的起始電場，局部放電就在這一區域發生，進而產生局部電弧並逐漸發展成整串的閃絡，泄漏電流迅速增大，同時伴隨著冰的融化。In order to solve the default of the limited valid scope and discontinuity characteristic, introducing the state continuous conversion gene based on establishment of respective mathematics model for low and magnitude current scope, and integrate with them reasonably then having established the mathematics model of suitable whole scope and having solved present mathematics model existent problems
本文針對目前電弧爐負載數學模型存在的適用范圍有限、特性不連續等缺點，在建立了分別適合大、小電流區域運行特性的數學模型的基礎上，引入狀態連續轉換因子，將分別適合大、小電流區域運行特性的數學模型有機結合為一個整體，建立了適合全范圍的數學模型，解決了目前數學模型存在的問題。The key process of the algorithm, called nodes transforming to arcs, is based on the calculation loads of coupling nodes and arcs loads from the loads of switch nodes. getting the area of coupling nodes is the most important process in nodes transforming to arcs. this paper presents a new method ， which uses the adjacency matrix of distribution network and the information matrix of
變結構耗散網路是一種新的配電網自動化演算法，由配電網開關頂點負荷求弧負荷和耦合頂點負荷的點弧變換是整個演算法中確定配電網饋線故障區域的基礎，而進行點弧變換的關鍵就在於分離耦合點區域。Combined with the practical situiation in distribution network, it ' s suitable to select graph algorithm as the theoretical algorithm base. based on structure variable dissipated network theory, this thesis detailedly discusses the transforms of base - to - shape, shape - to - base, vertex - to - arc, arc - to - vertex, over - heated arc dectection, load allotting, load balancing and optimum restoration
本論文基於變結構耗散網路理論，詳細討論了基形變換、形基變換、點弧變換、弧點變換、過熱弧搜尋、負荷分配、負荷均衡化以及優化恢復非故障停電區域供電等一系列與饋線自動化功能相關的處理演算法。Computational results show that the axial gas flow and the rotary flow, especially the axial gas flow plays the main role on the arc stability. the rotary flow can larger the region of the arc stability
研究結果表明，縱向氣流和旋轉氣流對電弧的穩定性確實起作用，尤其是縱向氣流，起著重要的作用，而旋轉氣流對電弧的穩定區域的增加效果顯著。Abstract : the image of arc zone of flux - cored underwater wet welding was developed with underwater ccd camera system and composed filter technology. the discussion is mainly focused on the theory of edge detection. an image edge detection method based on median filter and grads algorithm was developed to detect the arc burning zone and arc bubble zone efficiently, which laid the foundation for further analysis of underwater wet welding arc mechanism and process control
文摘:通過復合濾光技術和水下ccd攝像系統，採集出了藥芯焊絲水下濕法焊接電弧區域圖像，重點論述了邊緣檢測理論，確定了基於中值濾波和梯度運算元的電弧區域圖像邊緣檢測方法，有效地區分了電弧燃燒區域和電弧氣泡區域，從而為水下濕法焊接電弧的機理分析及水下焊接過程式控制制奠定了基礎。By the test of three - dimensional distribution, form character, rotating frequency and magnetic field intensity of rotating magnetic field, it showed that the magnetic field produced is a highly rotating magnetic field and mainly distribute on welding arc region, rotating frequency and magnetic intensity can be regulated through excitation power source
通過對產生磁場的空間分佈，形態特徵，以及旋轉頻率和場強大小的測試證明該磁場是一個高速旋轉的磁場空間，而且磁場主要集中分佈在焊接電弧區域內，磁場的旋轉頻率和場強大小都可以通過勵磁電源進行良好調節。Magnetic head is designed by six magnetic poles in symmetrical distribution, the design of excitation loop and excitation angle makes magnetic field act on welding arc region which could control welding arc effectively. the insulation, cooling and hermetization of magnetic head avoid the influence on magnetic field of outside ; miniaturization design of magnetic head could achieve different welding process
磁頭裝置採用六磁極對稱勵磁方式設計，勵磁線圈和勵磁角度的設計使產生的磁場恰好作用於焊接電弧區域以實現對電弧的有效控制;磁頭的絕緣，冷卻，密封設計避免了焊接過程中外界因素對磁場的干擾;磁頭整體的小型化使該裝置可以實現多種形式的焊接工藝。Abstract : through the analysis of the coordination characteristics between the switch and the fuses in combination, it is shown that the transfer current of combination can be decreased by reducing the prearcing time of fuses in the range of transfer current or by increasing the fuse - initiated opening time ( t0 ) of the switch. the ways to decrease the transfer current for present combinations are put forward
文摘:本文通過對組合電器中負荷開關與熔斷器之間的配合特性分析，認為減小熔斷器在轉移電流區域內的弧前時間或適當增加熔斷器觸發的負荷開關分閘時間t0 ，均可降低組合電器所需開斷的轉移電流值，並針對現有組合電器提出了減小轉移電流的具體方案。分享友人