電弧調制 的英文怎麼說

中文拼音 [diànhúdiàozhì]
電弧調制 英文
arc modulation
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 弧 : 名詞1. [數學] （圓周的任意一段） arc2. （古代指弓） bow
  • 調 : Ⅰ動詞1 （配合得均勻合適） harmonize; suit well; fit in perfectly 2 （使配合得均勻合適） mix; adju...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  1. According to the quickly adjustable characteristic of the peterson coil grounding system, this dissertation proposes a new control strategy. when the system is in operation, the strategy can limit the series resonance over - voltage by using the off - resonance method. when fault occurs, the strategy can conveniently suppressing arc by rapidly adjusting the inductance value of the peterson coil to the point, which the resonance with grounding capacitance of the power network is occurred

    依據可控硅控制消弧線圈接地系統的快速可控性，一改傳統的電網正常運行時調節消弧線圈接近於全補償的預調諧方法，提出正常運行時採用脫諧方法抑制串聯諧振過電壓；故障時立即調節消弧線圈電感量達到與對地電容諧振，以利熄弧的新型調節原理和方法。
  2. Analyze and compare pid and vague, single neuron etc. control strategy, and combine with single neuron self adaptive gain, self adaptive right value and preventive integral saturation etc. control strategy. have improved single neuron control algorithm, may restrain efficiently to disturb, reduce broken arc and short circuit etc. phenomenon, make systematic control effect and robustness get to strengthen, also have certain application reference value for the design of the dc arc furnace

    通過對pid 、模糊、單神經元等控制策略的分析比較，將單神經元增益與權值的自適應調節、抗積分飽和等控制策略相結合，改進了單神經元控制器演算法，可以有效抑制擾動，減少斷弧、短路等現象的發生，使系統的控制效果和魯棒性都得到增強，對電弧爐控制系統的設計也具有一定的應用參考價值。
  3. Then the idea of integral control of automatic resonance and single - phase earth faulted line selection was put forward

    並在此基礎上給出了補償電網中消弧線圈自動調諧與單相接地故障選線一體化的綜合控制思路。
  4. The silicon controlled trigger and it s auxiliary circuit could regulate simultaneously the controlling coil current of four series - parallel connected powers, so the purpose of making four powers output in step with was achieved, and the process of increasing progressively current after lighting arc and weakening current after going out arc was realized

    利用可控硅觸發器及輔助電路可以同時調節串並聯在一起的四臺電源控制線圈的電流，達到四臺電源同步輸出的目的，並且實現了等離子弧噴塗引弧時電流遞增和熄弧時電流衰減的過程。
  5. Based on the theory of piecewise - linear, the paper carries through the research of model self - adaptive control to electric arc - furnace electrode regulator system ( eafers ), and the digital self - adaptive control law of reference model is deduced. then, we designed the software simulation system of eafers according to the law, though which we studied the character of eafers. finally, a set of physical model of eafers, which is realized by hardware circuit, is designed according to the former research

    本文首先應用分段線性化理論，對電弧爐電極調節系統的模型參考自適應控制演算法進行了研究，推導出全數字化的模型參考自適應律；然後根據推導出的自適應律成功的設計出了的軟體模擬系統，用軟體對電弧爐電極控制進行了模擬研究；最後利用電子電路構造出一套完整的電爐煉鋼電極控制硬體模擬系統，對電爐電極調節進行了實驗室電路模擬研究。
  6. A novel current control mode pulse width modulation switched high frequency resonant arc igniting device is developed based on uc3842 and the principle is analyzed

    摘要採用uc3842設計了電流控制型脈寬調制開關式高頻振蕩引弧器，並對其工作原理進行了分析。
  7. The system uses the popular double - deck controlling, namely the host communicates online with plc, at the same time it communicates with other stations by tcp / ip protocol. the electrodes regulate timely, quickly and true, with controlling three - phase voltage and current, so that power is stable comparatively

    本系統合理控制三相電流、三相功率的大小，從而電極能夠實時、快速、準確地按照冶煉工藝要求進行調節，使電弧功率穩定在一定的范圍內，獲得期望的控制效果。
  8. At last, an experiential power supply was made, and a series of experiments is done. a lot of high - frequency pulse current was superposed on dcen current, modulated the welding current waveform we required and optimized the energy distribution, which satisfied the basic requirement of cathode cleaning

    最後製作了一臺實驗電源，並進行了一系列的電弧實驗，通過在變極性電源電流dcen基礎上疊加一系列脈沖電流，調制出所需電流波形，實現輸出能量的最優分配，在滿足陰極清理的前提下，最大限度地提高焊接效率。
  9. With the computer controlling the output of the digital signals and the analog signals, controls and adjusts startup, stop, turn and rotational rapidity of the transducer - electromotor and the strength of brake actuator ; installs the torque sensor on dynamical axis, and installs the encoder on non - dynamical axis of the dimensional globoidal indexing cam mechanism ; utilizes the virtual instrument language labview development the test and control system, with the computer real - time monitoring, late displays and storages the data of the test, and processes the data and analyses it

    利用計算機控制數字量輸出和模擬量輸出來達到控制和調節變頻電機啟停、轉向、轉速;控制制動器的啟停和加載力;在弧面分度凸輪的加載軸和空軸上安裝扭矩傳感器和編碼器;應用虛擬儀器語言labview開發試驗臺的測控軟體系統，用計算機進行實時監測與事後顯示與存儲，並進行信號處理與分析。
  10. The switch is not only when switching over with production of electric arc, mechanical contact head easy to be damaged, but also it is slow to regulate, ca n ' t frequently operate, so limit the range of application of this kind of switch

    這種開關不僅切換時伴有電弧的產生，機械觸頭容易損壞，而且調節速度慢，不能頻繁操作，因此限制了這種開關的應用范圍。
  11. The tap - changer is made with solid state relay as its working mechanism and controlled by microprocessor. this switch has totally cancelled the mechanical drive organization, by the microprocessor according to the voltage of second side microprocessor decide the working condition of solid state rely, high regulation speed, need not transition resistor, rush current is low. operating frequently ; there is no electric arc to produce, can put in the fuel tank of the voltage transformer directly ; the structure is simple, the fabrication cost is low, benefit and use widely among the voltages transformer of distribution

    其中的有載調壓分接開關，它是一種完全由固態繼電器作為分接開關執行機構，由單片機控制的有載自動調壓的變壓器分接開關。該開關完全取消了機械傳動機構，由單片機根據變壓器二次側電壓的高低，決定與變壓器各分接頭聯接的固態繼電器的工作狀態。調節速度快，改變分接頭時不需過渡電阻，沖擊電流小，可頻繁操作；無電弧產生，可以直接放在變壓器油箱中；結構簡單，造價低，便於在配電變壓器中推廣使用。
  12. Using metal for reaction material, sno2 and tio2 nano - powders were obtained through dc transferred arc plasma with purity more than 98 % and average size of particle being l00nm and 60nm, in the same time the particle size could be adjusted according to the cooling medium

    用直流電弧等離子體「蒸發?凝聚法」以金屬塊體為原料，制備出了純度大於98平均粒度分別為100nm和60nm的sno _ 2及tio _ 2納米粉末，並且粉末的粒度可以通過調整冷卻介質來加以控制。
  13. Application to parameters of pid control based on genetic algorithm

    電弧爐電極調節系統的自校正控制
  14. The results prove that the scheme increases the stability of electrode apparently, current fluctuating has been reduced, speed of system echo has been improved. the system has fine self - adaptive ability and fine ability to resist interference

    現場調試結果表明採用的控制方法大大提高了電極控制的穩定性，電弧電流波動降低，系統的快速性大大提高，系統具有較強的自適應能力和魯棒性。
  15. The paper explains the method of the petersen coil parameter selection and expatiates the working principle of micro - computer controller. new methods of on - line measuring of the capacitive current and the control of the series resistance are put forward ? which lead to the integration of the automatic resonance and the faulted line selection in a compensating network

    文中說明了消弧線圈參數的選擇方法，闡述了微機控制器的工作原理，提出了在線測量補償電網對地電容電流以及控制串聯電阻的新方法，實現了補償電網自動調諧與單相接地選線的一體化。
  16. The quick adjustment of the inductance value of the peterson coil is realized by using a method, which can control the trigger angle of the thyristor with power electronics technology

    採用電力電子技術實現消弧線圈的控制是利用可控硅的相控方式對消弧線圈實現電感量可調的原理。
  17. A novel structure of peterson coil with particular design can fully satisfy above requirements and allow us to use the lower critical voltage - level thyristor in the 6 - 10kv and higher voltage power system. the novel peterson coil design resolves key problems of using thyristor to control the peterson coil, and becomes the foundation of realizing quick adjustment of the inductance value of the peterson coil

    由於其特有的諧波問題、耐壓問題等，本論文涉及的一種新型消弧線圈，通過消弧線圈的特殊設計，使常規耐壓范圍的可控硅技術可以應用於6 - 10kv和更高電壓等級的系統，解決了可控硅控制應用於消弧線圈的根本問題，為實現電感量的快速調節打下了基礎。
  18. Based on above studying, current regulation control system and the electrode of application matlab software for the dc arc furnace have been simulated

    在此基礎上，應用matlab軟體對電弧爐的電極與電流調節控制系統進行了模擬。
  19. In order to settle this problem, basing on a power electronic controlled fast adjustable perterson coil, this paper provide a new principle of selecting the line with the fault, which make use of the dynamic changes in the current through the zero order line

    為了解決這一問題，本文在一種由電力電子技術控制的快速調節消弧線圈的基礎上，提出一種新的故障選線原理，利用線路零序電流的動態變化量來選線。
  20. The paper presents a new e. a. f ( electric arc furnace ) adaptive control method based on a neural network ' s compensation by predicting. the neural network is used here to predict the condition of e. a. f, then to control an actual system by compensating the outputing of routine controller. the dynamic modification of the weighting value of a neural network by improved dbd algorithm serves as an adaptive method. hence the system can adapt itself better to the variations in load and external interference. which has yielded a satisfied control quality

    電極調節器採用一種新的電弧爐電極自適應控制方法- - -基於神經網路預估補償的自適應控制。採用神經網路預估對象狀態，進而對常規控制器的輸出做補償以控制實際對象，利用改進的dbd演算法動態修改神經網路權值作為自適應方法，使系統較好地適應負荷和外擾的變化，從而獲得滿意的控制質量。
分享友人
分享到 Line

分享到臉書