電性能試樣 的英文怎麼說

中文拼音 [diànxìngnéngshìyàng]
電性能試樣 英文
electrical test specime
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 性 : Ⅰ名詞1 （性格） nature; character; disposition 2 （性能; 性質） property; quality 3 （性別） sex ...
  • 能 : 能名詞（姓氏） a surname
  • 試 : 名詞（古代占卜用的器具） astrolabe
  • 樣 : Ⅰ名詞1. （形狀） appearance; shape 2. （樣品） sample; model; pattern Ⅱ量詞（表示事物的種類） kind; type
  1. Tensile properties and impact properties measurements were done at room temperature. the volume resistivity of rectangular samples was measured using a zc36 electrometer and a high 240a voltage supply, for samples with a low resistivity level a dt - 9205b digital multimeter was used, silver paint was applied to ensure complete contact between sample and electrodes, namely, to eliminate the contact resistance. the phase morphology of blends was also studied using a jeol jsm - 5900lv scanning electron microscope ( sem )

    體積電阻率的測定：當r _ v 10 ~ 8時，製成100 100 4mm板材，用zc36型高阻儀測量；當r _ v 10 ~ 8時，用dt - 9205b型數字式萬用表測試試樣的體積電阻，為了減小接觸電阻對測試的影響，採用銀導電膠將銅片粘接在試樣的兩個端面上，靜置24小時，待銀導電膠凝固，試謝長瓊:熱拉仲對pet / pe / cb復合導電體系形態和性能的影響樣的電阻穩定后再測量。
  2. The structures and characteristics of several graphite samples are measured by means of powder x - ray diffraction ( xrd ), brunauer - emmer - teller ( bet ) surface area measurement, inductively coupled plasma ( icp ) spectroscopy, particle size analysis and electrochemical measurements. the effects of origin, structure, impurity, particle size, specific surface area of carbon materials on the electrochemical characteristics are studied. a synthetic graphite with abundant resources, low cost and favorable performance is determined as the raw material for modification of graphite

    採用xrd 、 bet 、 icp 、激光粒徑分析及電化學性能測試等方法，對國內外多種典型石墨樣品的結構與性能進行比較，研究石墨材料的來源、晶體結構、雜質含量、顆粒大小、比表面積等因素對其充放電性能的影響，確定一種性能較好、價格低廉、來源廣泛的普通人造石墨粉作為熱處理與摻雜改性、以及復合結構炭材料研究的原材料。
  3. The tensile strength and young ’ s modulus of cf / ep specimens before and after vacuum thermo - cycling were measured by an electrical universal material testing machine. an electron scanning microscope was used to perform the surface morphology and fractography of specimens

    真空熱循環試驗前後cf / ep層合材料的拉伸性能由電子萬能材料試驗機完成，本文利用掃描電鏡觀測試樣表面形貌和拉伸后的斷口形貌。
  4. The chemical compositions of sei films formed on the interfaces of a3000 samples in different electrolytes during the first charging process are mainly li2co3 and lioco2r, but their textures are different. the sei films formed in ec - based electrolytes are thin and compact, which can prevent the solvated lithium ions from cointercalating between two graphene layers of the graphite crystallites effectively, therefore samples a3000 have small irreversible capacities and good compatibilities with this kinds of electrolytes. however, the sei films formed in pc - based electrolytes are thick but defective, which could not effectively prevent solvated lithium ions from intercalation, therefore sample a3000 shows large irreversible capacities in pc - based electrolytes and bad compatibilities with this kind of electrolytes

    A _ （ 3000 ）試樣在六種不同的電解液中，首次充電過程中所形成的sei膜，其化學組分均為碳酸鋰和烷基碳酸鋰，但在ec基電解液中形成的sei膜薄而緻密，可以有效地阻止溶劑化鋰離子插入石墨層間，不可逆容量少，表現出與a _ （ 3000 ）試樣有良好的相容性；在pc基電解液中形成的sei膜厚，且有缺陷，不能有效地阻止溶劑化鋰離子嵌入試樣中石墨微晶的層間，不可逆容量大，與a _ （ 3000 ）試樣的相容性極差。
  5. Standard test method for alternating - current magnetic properties of toroidal core specimens using the voltmeter - ammeter - wattmeter method

    使用伏特計-電流計-瓦特計方法測試環形鐵芯試樣交流磁性能的標準試驗方法
  6. We expounded the characteristic between current driving method and voltage driving method, ac driving method and dc driving method, passive driving method and active driving method 。 through theory research we find the dc driving method is also suitable for oled driving 。 an ac - voltage driving circuit is proposed and designed

    通過分析發現， oled不僅適合於電流驅動，對于電壓驅動同樣可以實現其優異的圖像顯示。設計了一種交流電壓驅動電路，利用所設計的電路對oled的交流驅動特性進行了測試和分析，通過實驗研究了直流驅動和交流驅動對oled性能的影響。
  7. When fillings is other materials ( unprocessed montmorillonite, powder coal ash, co - composite of powder coal ash and organo - montmorillonite, co - composite ofcarbonizing calcium and organo - montmorillonite ) in the binder and content of organo - montmorillonite in the binder is five percent decided by tensile - shear experiment, tensile - shear strength of binder is up to tiptop ; at the same time, this paper carries out abrasion experiment, and, by comparison, concludes abrasion property of coating is optimum when content of organo - montmorillonite in the binder coating is five percent, and observes abrasion sample under set

    當膠粘劑中填料為其它物質（未處理蒙脫土、粉煤灰、粉煤灰和有機化蒙脫土共復合、碳化鈣和有機化蒙脫土共復合）時，通過拉伸剪切試驗確定膠粘劑中有機化蒙脫土含量為5時，膠粘劑的拉伸剪切強度最高；同時進行了沖蝕磨損試驗，通過比較得出，當膠粘劑塗層中有機化蒙脫土含量達到5時，塗層的耐沖蝕磨損性能最佳，並對沖蝕磨損試樣在掃描電子顯微鏡（ set ）上進行觀察。
  8. The results show that the properties of the graphitized samples based on high quality eca and quantitative low ashes raw materials produced by proper carbon technics have reached to the demand of the cathode materials for high - current aluminium electrolysis cell

    結果表明，以無煙煤為主要原料，配以一定比例的少灰料作為骨料，通過適當的炭素工藝制備的石墨化陰極材料試樣，其常規理化性能可以滿足大電流鋁電解槽用陰極材料的要求。
  9. Energy conservation and and reformation of power plants " heat installation affect a lot on the efficient performance of opertion of power plant. pump and fan take a large proportion in power plant and resume much electric energy. so there is much energy conservation pationlity in them. and we should have strong tools and theories " support to reform them. we can combine the theory modeling and engineering design manufacture by the bussiness software such as fluent. in order to take full advantage of the powerful function of fluent and increase absolutely its conveniece and interaction, we should develop fluent secondly. this paper puts the idea firstly demostricly to substitute the performance test of pump and fan to get the integrative system of the optimization and computer aid design, and so we can increase greatly of the efficiecy and quality of the facility reformation. the main idea about the secondary development of fluent in this paper is based on the secondary development of gambit, the modeling and meshing s oftware of fluent, and simplify the modeling and meshing of gambit. meanwile, the data management base on web browser kind is adopted for the convenience of optimization and parameterization, and the journal files createdly recently can get new medeling and meshing files that can be used by fluent. so the designer can focus on the computer scheme and the result analysis without care the fussy designing and optimiziation. so we can increase greatly the optimization efficiency

    泵與風機在電廠中占較大數量比例，且消耗大量電能，節能潛力巨大，對其改造需要強有力的工具和理論支持，用商用cfd軟體如fluent可實現泵與風機改造中的理論模擬與工程設計製造間的結合。為了充分發揮fluent的強大功能，又能最大程度地提高其方便性與交戶性，應對其進行二次開發。本課題在國內首先提出對fluent進行二次開發，替代泵與風機性能試驗，形成一體化的優化、輔助製造系統，可大大提高設備改造的效率與質量，其主要思想是基於fluent的cad構體軟體gambit進行二次開發，簡化了泵的構體過程，同時，為了優化及參數化方便，採用基於webbrowser的數據管理方式，生成新的記錄文件同時產生新的fluent計算能識別的圖形網格文件，這樣就將設計優化者從繁瑣的圖形設計及優化中解脫出來，專注于對計算方案的確定及計算結果的分析，極大地提高了設計優化的效率。
  10. Samples with various compositions were prepared through different calcined temperature, sinter temperature and different maintained time at sinter temperature. the structure, density, shrinkage, and piezoelectric properties were investigated

    選取部分組成點，採用不同的預合成溫度、燒結溫度和保溫時間制各樣品，測試各樣品的晶體結構、體積密度、線收縮率和壓電性能。
  11. Practice heating test of spread sample has been underway and contrasted with traditional electric furnace. production technology, structure and property of the coating have been studied in order to search for a. new technology method with not only enhancing thermal conductivity of coating but also dropping its electrical conductivity and reducing its production cost

    對試樣進行了關鍵熱學性能、電學性能的測試，並進行掃描電鏡分析，對塗覆樣品進行實際加熱測試，並和傳統意義上的電爐進行對比，通過對耐火塗層生產工藝、組織及性能的關系的研究，以探求一種既能提高塗層的導熱性能又能降低導電性能和生產成本的工藝方法。
  12. Through study on the electrical performance of sn - in2o3 nano powder, some conclusions were drawn. when sn - in2o3 precursor was calcinated at 700 - 1000, low square resistance was got. the resistance was lower when sn - in2o3 precursor was calcinated in vacuum than air condition

    Sn - in _ 2o _ 3納米粉體的電性能研究表明： sn - in _ 2o _ 3前驅物在700 - 1000煅燒，方塊電阻較低，真空條件下煅燒試樣的電阻比空氣條件下煅燒試樣的電阻低，南京工業大學碩士學位論文中文摘要sno :摻雜10wt %左右時，試樣方塊電阻最低。
  13. The properties of all samples were investigated, it is the same to the pzt ceramics, samples in the composition range of mpb exhibited best piezoelectric performance

    測試了各組成點樣品的壓電性能，結果表明，與pzt基含鉛壓電陶瓷相似，材料在準同型相界組成范圍內壓電性能最佳。
  14. The thesis mainly investigated the bati _ 4o _ 9 ( bt _ 4 ), which has the lowest dielectric loss in ba - ti system, and ( ba, sr ) tio _ 3, the a position substitute compound of batio _ 3. the dielectric properties of bt _ 4 / bst with different preparation way and different elements doping were investigated. a archimedes method, xrd, sem, impedance analyzer, network analyzer and hakki - coleman method were used to investigate the density, phase formation, microstructure, dielectric properties and doping mechanisms

    本論文以在ba - ti系中具有最低介電損耗的bati _ 4o _ 9 （ bt _ 4 ）高頻介質陶瓷和batio _ 3a位sr取代而得的（ ba ， sr ） tio _ 3 （ bst ）高頻介質陶瓷作為研究對象，對不同粉體制備方法制備的bt _ 4 / bst高頻電介質材料進行不同元素的摻雜，運用阿基米德方法， x射線衍射分析儀，掃描電子顯微鏡和阻抗分析儀，網路分析儀， hakki - coleman法等方法手段和測試儀器測試燒成樣品的密度，相組成情況，微觀結構和介電性能，探討造成介電性能起伏的形成機理。
  15. The influences of other factors ( the charging - discharging current density, the granularity of a30 00, the content of acetylene black and the content of ptfe ) on the charging - discharging performance of sample a3000 were also investigated by the orthogonal method through galvanostatic charging - discharging experiments

    結合恆電流充、放電實驗，採用正交法分析了充、放電電流密度、 a _ （ 3000 ）試樣的粒度、炭膜中乙炔黑的含量和ptfe的含量對a _ （ 3000 ）試樣的充、放電性能的影響。
  16. The charging - discharging performances of these samples were examined with galvanostatic charging - discharging experiments and powder microelectrode cyclic voltammetry experiments

    運用恆電流充、放電實驗和粉末微電極循環伏安實驗來檢測上述試樣的充、放電性能。
  17. The charging - discharging performances of these samples used as the negative electrodes in lithium ion batteries ( lib ) were investigated by galvanostatic charging - discharging experiments and powder microelectrode cyclic voltammetry experiments

    用恆電流充、放電實驗和粉末微電極循環伏安實驗來檢測上述ant試樣用作鋰離子電池負極材料時的充、放電性能。
  18. The experimental results are as follows : ( 1 ) : httmax made great influence on the microstructures and the charging - discharging performances of p16 and p14 samples. when httmax < 2000, the graphite microcrystals did n ' t appear

    實驗結果表明： （ 1 ） ：在固相炭化和石墨化過程中， htt _ （ max ）對p16 、 p14試樣的微觀結構和充、放電性能有很大影響。
  19. Picks up various compositions, adopts different poling voltage, poling temperature and maintained different time at poling voltage, and makes sure the best poled craftwork system by measuring the samples ' piezoelectric properties

    摘要選取部分樣品，採用不同的極化電壓、極化溫度和保溫時間，測試其壓電性能，確定最佳的極化工藝制度。
  20. In this paper, the volume density, hardness, bend strength and electrical conductivity of cf / cu ( c ) - cu composites have been tested. the results show that, after graphite is coated by copper, the electrical conductivity, bend strength and volume density of cu ( c ) - cu composites is remarkably increased. with the increase of copper coated graphite, the static characteristics are reduced

    本論文通過對不同成分復合材料試樣的密度、硬度、抗彎強度和電阻率等靜態性能的測試發現，石墨粉表面鍍銅提高了材料的導電性能，同時材料的硬度、抗彎強度都有顯著的提高；但當鍍銅石墨粉繼續增加時，材料的導電性能降低，密度、硬度和抗彎強度下降。
分享友人
分享到 Line

分享到臉書