電源模塊中斷 的英文怎麼說

中文拼音 [diànyuánmókuāizhōngduàn]
電源模塊中斷 英文
ccontint
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 源 : 名詞1. （水流起頭的地方） source （of a river）; fountainhead 2. （來源） source; cause 3. （姓氏） a surname
  • 模 : 模名詞1. （模子） mould; pattern; matrix 2. （姓氏） a surname
  • 塊 : 名詞（古時佩帶的玉器） penannular jade ring （worn as an ornament in ancient china）
  • 斷 : Ⅰ動詞1 （分成段） break; snap 2 （斷絕;隔斷） break off; cut off; stop 3 （戒除） give up; abstai...
  • 電源 : source; current source; electric source; power pack; power supply; power source; source of power ...
  • 模塊 : camac module,camac
  1. In the hardware design, the paper completes modules ’ design like outside memory, patulous a / d, patulous d / a, rs232 communication, ecan communication, led control, keyboard control, distant control, emulation, reset, logic voltage switch, dsp supply power regulate and ac - dc power circuit, as well as room layout design like anterior panel, back panel etc. and dsp transfers data with peripheral equipments except outside memory using serial ports. besides, the whole circuit is configured in interrupt response. thus, it can meet system demand as well as take full advantage of tms320f2812 ’ s hardware resource. in the software design, the paper finishs programs like the interface programms intercommunicates with people, the distant control program, ad and da modules ’ control program, in addition, the paper select the velocity and acceleration state - feedback algorithm and is written in the program. the software design uses dsp integrate exploiting environment named ccs2. 2 of ti inc. as software instrument, and programs with the combination of c language and assembly language. moreover, in order to maintenance or modify the software expediently and shorten software ’ s exploitation time, the design adopt software modularization technique. finally, some air cylinder experiments are carried out to proved that the pneumatic controller is very practical

    在硬體設計中，本文完成了片外存儲器擴展、 a / d擴展、 d / a擴展、 rs232通信介面、 ecan通信總線介面、液晶顯示控制、鍵盤控制、遠程控制、模擬、復位、邏輯電平轉換、 dsp工作電源校正電路和ac - dc電源等模塊設計以及控制器前面板、後面板等的空間布局設計。其中dsp與除外部存儲器的外圍設備之間的數據傳送全部採用串口通信，同時系統電路配置成中斷響應方式，這樣既滿足了系統要求，又充分利用了tms320f2812的硬體資源。在軟體設計中，本文完成了人機界面功能模塊、遠程控制模塊、 ad擴展模塊、 da擴展模塊、速度和加速度狀態反饋的控制演算法的程序設計。
  2. Experiments have failed in the process of debugging station fire mode of the first opening segment of guangzhou metro line 3, the main reason is the delay protect module of wind valve which cut off power supply

    摘要廣州地鐵3號線首通段車站火災模式調試過程中，出現火災模式執行失敗，主要原因在於風閥延時保護模塊動作切斷電源。
  3. In the design, the mechanism of distributed power sources is applied to the power module in stage one, providing a highly reliable power supplying solution to board, which implements hot swap, slow power supply and automatically cutting off etc. thus to improve the sta bility of the power system

    其中，在階段一平臺的電源模塊設計中引入分散供電機制，設計了一種高可靠的板級電源解決方案，該方案能夠完成熱插拔、緩上電以及自斷電管理等功能，以提高電源系統的穩定性。
  4. According to the combination of theoretical analysis and the actual need of power branch, the data resource of scad a system under control center based on unmanned substations is fully used to develop the fault diagnosis system and verification of relay protection sensitivities based on the topology configuration of real - time and emulation state system

    根據電力運行部門的實際需求，在理論分析研究的基礎上，充分利用城市電網無人值班變電站控制中心scada系統的數據資源，開發了城市電網故障診斷系統模塊和基於實時和模擬拓撲結構的保護靈敏度在線校驗模塊。
  5. This paper projects a utility subdividing drive system of step motor, which consists of digital control module, drive module and power module, it uses at89c52 single chip processor as the core, it realizes the external event or generates control signal by i / o interface, timer and external interruption, the system introduce pld device and isp technology to the design of phase sequencer, it simplified circuit and improved the anti - disturbing capability by using abel - hdl language, this system can realizes data memory, velocity digital control and led display, etc. this paper adopted firstly the single - chip technique to design control system, which replaced old complicated logic control circuit and simplified test process

    本文研究了一種實用的步進電機細分驅動系統，由數字控制模塊、驅動模塊和電源模塊組成，系統以at89c52單片機為核心，通過單片機的i o口、定時器計數器中斷來實現外部事件監控以及控制信號的產生，系統將可編程邏輯器件（ pld ）器件和在系統編程（ isp ）新技術引入到細分驅動環行分配器的設計，通過abel _ hdl語言編程實現硬體軟化設計和邏輯重構，大大簡化了電路，並提高了電路抗干擾能力。使系統實現參數存儲，速度數字控制，數碼顯示，進退刀控制等功能。
分享友人
分享到 Line

分享到臉書