電源轉接盤 的英文怎麼說

中文拼音 [diànyuánzhuǎnjiēpán]
電源轉接盤 英文
power su ly changeover panel
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 源 : 名詞1. （水流起頭的地方） source （of a river）; fountainhead 2. （來源） source; cause 3. （姓氏） a surname
  • 轉 : 轉構詞成分。
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 盤 : Ⅰ名詞1 （盤子） tray; plate; dish 2 （形狀或功用像盤的東西） sth shaped like or used as a tray pl...
  • 電源 : source; current source; electric source; power pack; power supply; power source; source of power ...
  • 轉接 : change-over; throw-over; switch; transfer; transit; reset; adapter coupling; built-up connection
  1. The system is formed with explosion - proof kinescope, explosion - proof braket, explosion - proof decode, matrix controller, keyboard controller, 232 to 485 switch, color kinescope, digital harddisk kinescope system, display, manostat, explosion - proof junction boxes and special cable

    該系統由防爆攝像儀、防爆雲臺、防爆解碼器、矩陣控制器、鍵盤控制器、 232轉485轉換器、彩色攝像機、數字硬盤錄像系統、監視器、穩壓電源、防爆接線箱及專用電纜等組成。
  2. Through a keyboard converter, link one end with the computer s keyboard port and the other end with the keyboard you must first cut open the rubber cover at the tip of the serial rs232 before connecting the wire ; put the 5v power source into the connecting part of serial 232 and put the serial rs232 connector from the control box into the 9 - pin socket of the computer

    取電源部分通過一個鍵盤轉換頭必須先將rs232口連接頭的旁邊的小膠皮頭拔開，才可以將電源來線入，將一頭連在主機的鍵盤口，另一頭連接計算機鍵盤.將取到的5v電源的一個小頭，插入232口的連接處將控制盒伸出的rs232連接頭，插入主機的9針孔
  3. According to the request of this subject, we have developed the system hardware and software for the slave device and the inspection software running on the pc. in this paper all of the followings is illustrated detailedly, such as the research on the principles of measurement and its realization, three means of water - level measurement that are separately based on photo electricity coder, pressure sensor and potentiometer ; selection of the microchip, we choose an advanced integrated soc ( system on chip ) microchip c8051f021 as the main controller ; realization of signal sampling, processing and its conversion in the mcu ; application of high precision 16 bits adc cmos chip - - ad7705 in our system, designing its interface with the microchip and relevant program ; using a trickle charge timekeeping chip ds1302 in the system which can provide time norm and designing of its i / o interface and program ; additionally, a 4 ~ 20ma current output channel to provide system check - up using ad421. in the system, ad421, ad7705 and the microchip compose spi bus ; to communicate with the master pc, here we use two ways which are separately rs232 and rs485 ; moreover, there are alarm unit, keyboard unit, power supply inspection unit and voltage norm providing unit in the system

    針對研製任務的要求，課題期間研製了下位機系統硬體和軟體，開發了上位機監控軟體，其中所作的具體工作包括：測量原理的研究和在系統中的實現，在本次設計中用三種方法來進行水位測量，分別是旋轉編碼器法、液位壓力傳感器法和可變電阻器法；主控晶元的選擇，我們選用了高集成度的混合信號系統級晶元c8051f021 ；實現了信號的採集和處理，包括信號的轉換和在單片機內的運算；高集成度16位模數轉換晶元ad7705在系統中的應用，我們完成了它與單片機的介面設計及程序編制任務；精確時鐘晶元ds1302在系統中的應用，在此，我們實現了用單片機的i o口與ds1302的連接和在軟體中對時序的模擬，該晶元的應用給整臺儀器提供了時間基準，方便了儀器的使用；另外，針對研製任務的要求，還給系統加上了一路4 20ma模擬信號電流環的輸出電路來提供系統監測，該部分的實現是通過採用ad421晶元來完成的，本設計中完成了ad421與單片機的spi介面任務，協調了它與ad7705晶元和單片機共同構成的spi總線系統的關系，並完成了程序設計；與上位機的通信介面設計，該部分通過兩種方法實現： rs232通信方式和rs485通信方式；系統設計方面還包括報警電路設計、操作鍵盤設計、電源監控電路設計、電壓基準電路的設計。
  4. In the second chapter, equivalent circuit of the eddy current sensor is firstly analyzed. based on that, the carrier signal generating circuit that is realized by the lc periodic circuit is introduced, thus, the carrier signal of standard frequency is obtained through the trimming capacity. subsequently, the disc type rotational armature generator and the rotational coupling transformer are separately leaded in to realize the power supplies of the carrier signal generating circuit and output of the measuring signal

    在傳感器設計一章中，首先對渦流傳感器進行等效電路分析，在此基礎上分析了由電感、電容諧振電路構成的載波信號發生電路，並通過微調電容獲得了標準頻率的載波信號；接下來提出了採用盤式旋轉電樞發電機解決載波信號發生電路電源供給問題的方案，同時通過旋轉耦合變壓器的引入，使得測量信號輸出問題很好地解決；本章最後給出的一組實驗曲線充分說明了這一方案的可實現性。
  5. While connecting the power supply, notice the knife dish to revolve the direction

    接通電源時，注意刀盤的旋轉方向。
分享友人
分享到 Line

分享到臉書