電熱分析 的英文怎麼說

中文拼音 [diànrèfēnxī]
電熱分析 英文
electrothermal analysis
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 分 : 分Ⅰ名詞1. （成分） component 2. （職責和權利的限度） what is within one's duty or rights Ⅱ同 「份」Ⅲ動詞[書面語] （料想） judge
  • 析 : Ⅰ動詞1. （分開; 散開） divide; separate 2. （分析） analyse; dissect; resolve Ⅱ名詞（姓氏） a surname
  1. Finite volume method in thermal analysis of avionics

    高可靠性航空電子設備熱分析中的有限體積法
  2. However, the manufacture process of twt is so complicated that many kinds of subject, such as electron optics, magnetics, cathode electronics, microwave electronics, electronmagnetic fields theory, material science, mechanics and calorifics are involved in

    行波管的研製涉及到電子光學、磁學、陰極電子學、微波電子學、電磁場理論、材料學、機械與熱分析諸多學科，工藝過程十分復雜。
  3. In experiment, the dsc technique was used to analyze the effect of electric fields on the precipitate kinetic of al - li alloy solutionized with electric fields. the energy spectrum, tem and sem techniques are employed to investigate the elements solution, precipitates, fracture character, conductivity and vickers hardness. also, the solidification of al - cu eutectic alloy was conducted with the influence of electric fields

    在實驗上，利用dsc熱分析技術，分析了電場作用對al - li合金相析出動力學的影響；採用能譜成份檢測，透射電鏡和掃描電鏡等多種微觀檢測手段，對鋁合金的析出相，斷裂特徵、合金電導率和維氏硬度等性能在電場作用下的變化進行了系統的研究，並觀察了al - cu共晶合金在電場作用下的凝固組織。
  4. The system will build up mathematic model according to the operating characteristic of electrical apparatus of ssr. and then analyze it and work out the nephogram

    這一部分得到造型設計系統的造型后，首先根據固態繼電器的電器特性構造其熱分析數學模型，然後對模型進行求解，得到其熱分析雲圖。
  5. The composition of sample was identified by means of x - ray diffractometer ( xrd ). magnetic properties were measured by vibrating sample magnetometer ( vsm ). the combustion behavior and crystallization process of the gel were studied by means of differential thermal analysis - thermogravimetric analysis ( dta - tg )

    利用x射線衍射儀（ xrd ）確定樣品物相，振動樣品磁強計（ vsm ）進行磁性測量，綜合熱分析儀研究凝膠的燃燒和析晶過程，掃描電子顯微鏡（ sem ）和透射電子顯微鏡（ tem ）觀察粉末的形貌與粒度。
  6. The major performances of concrete and mortars, which are mixed with different quantities of expansion admixtures under the same mix proportions, are studied systematically and deeply in this work. sulphoaluminate mixed with a type of new expanding component by use of the composite methods are studied in the laboratory, and some achievements have been obtained. the service conditions, the characteristics and the shortcomings of expansion admixture in the concrete engineering are analyzed and summarized based on literatures, and the expanding mechanism of concrete is discussed

    本文試圖從膨脹劑不同摻量研究其對混凝土和砂漿主要性能的影響，進行了一系列宏觀力學性能試驗研究；利用差熱分析（ dta ） 、掃描電子顯微鏡（ sem ）等分析手段對鈣礬石等水化產物的結晶和生成量、形貌特徵進行微觀分析；並採用復合方法摻加新型膨脹組分對硫鋁酸鹽類膨脹劑（ uea ）進行了改性試驗研究，根據多因素模糊綜合評價方法就各類膨脹劑的主要性能進行綜合評價，得出摻加新型膨脹組分pt的膨脹劑性能較優，取得了明顯的效果。
  7. Potash micatization is one of the main hydrothermal alteration minerals genetically related to the lead - zinc - silver deposit. it usually shows as muscovitization, sericitization and illitization. this paper presents a comprehensive study on the chemical composition of potash mica, adapted the follow methods : electronic probe, differential thermal analysis, x - ray diffraction analysis. at last, the structu ral characteristics and the geological environment of potash mica forming have been discussed

    系統地研究了鉀質白雲母化的礦物組成，採用了電子探針差熱分析x射線分析等技術方法，探討了鉀質白雲母的結構特徵和形成的地質環境及找礦意義。
  8. Analysis for magnetic field of srm is very complicated since the flux waveforms in different parts of the motor vary with motor phase, stator pole and rotor number, also with the winding connections, etc, which results in the srm losses, especially iron loss calculation difficult. the temperature analysis due to the losses has become a study hot spot

    Sr電機鐵心的磁通波形不僅與電機的相數有關，還與定、轉子齒極數、定子繞組連接方式等密切相關，從而使得sr電機磁場分析很復雜，復雜的磁通密度波形導致電機損耗特別是鐵損的計算非常困難。電機的損耗又會引起電機的溫升，因此高性能的sr電機的熱分析也成為目前的研究熱點。
  9. The glass powder size, morphology and mechanical properties of glass / epoxy composites were measured by means of laser particle size analyzer, sem, material testing machine and tga respectively

    利用激光粒度分析儀、電子多功能實驗機、 sem 、熱分析儀等剛試粉料粒徑、結構形貌以及機械強度等性能。
  10. The morphology of some specimens were analyzed by scanning electron microscopy. we have also studied the thermal stability of alloy powders by differential scanning calorimeter

    用x射線衍射儀對球磨后粉末的結構進行了分析，用dsc熱分析儀對樣品的熱穩定性進行了分析，用掃描電子顯微鏡對樣品的形貌進行了分析。
  11. Rail and armature joule heating of an electromagnetic rail gun

    電磁軌道炮導軌和電樞中的焦耳熱分析
  12. Plastics piping systems. determination of moisture content in thermoplastics by coulometry

    塑料管道系統.用電量分析法測定熱塑性塑料的含水量
  13. Plastics piping systems - determination of moisture content in thermoplastics by coulometry ; german version en 12118 : 1997

    塑料管道系統.電量分析法測定熱塑性塑料含水量
  14. The object to study in this paper is the electric heat reservoir boiler, which is used to supply heat water and bask for the resident population. the use of the system define the character of the output medium with the lower request on quality and parameter, at the same time, it ask the boiler should has the higher character on the respect of the cost, reliability, economy, and so on. hence, the paper carefully design and study the system for the choice and design of the boiler core heating componet, the lay of the heat exchanger, the working status of the heat reservoir equipment, the adjustment and control mode of to supply heat water. the study work mainly include underside some contents, forexample : 1. to confirm the heat medium parameter to adapt the requirements of the most of the heating equipments and to design the instruction of the boiler and heat reservoir as simple as possible

    圍繞上述原則，本文從電熱鍋爐核心加熱元件的選型及設計、換熱面的布置、蓄熱設備的運行工況、供熱的調節方式以及控制方法進行了較細致的研究和計算，具體研究工作有以下幾個方面： 1 .根據使用要求，確定適用於多數採暖設備的熱介質參數，設計在結構型式上盡可能簡單的鍋爐和蓄熱器； 2 .對製造加熱元件電熱管的各種材料進行了對比和分析、在結構尺寸上進行了仔細的分析和計算，根據實際使用條件給出合理的設計，使其具有較高的可靠性和使用壽命； 3 .對不同換熱面布置形式進行傳熱分析。
  15. The plate - tube evaporator, the single back - fin evaporator and the box condenser. after analyzing the physical model and setting up the mathematical model according to the two - phase flow of adiabatic capillary tubes, it also numerically simulates and analyzes the different effects of main parameters on the capillary tube length. based on the heat transfer analysis and counting of thermal insulation layer, the cad system accomplishes the parametric design and drawings of the refrigerator body

    該系統完成了對典型製冷裝置的換熱器部件，如板管式蒸發器、單脊翅片管式蒸發器、箱壁式冷凝器的參數化設計和繪圖；分析了絕熱型毛細管兩相流的物理模型，並建立數學模型，對絕熱型毛細管各主要參數對其長度的影響進行了數值模擬和計算分析；基於對電冰箱箱體絕熱層厚度的傳熱分析和計算，完成了整個箱體的參數化設計和繪圖工作。
  16. Microstructure of the composite layer was analyzed with help of optical microscope, scanning electronic microscope ( sem ), electronic probe microanalysis ( epma ) and x - ray diffraction ( xrd ). the compacting of the billet and the forming mechanism of the carbide reinforcement were studied based on thermodynamics and kinetics of reaction, sintering theory and the result of dta. at the same time, the wear - resistance of the composite layer was studied under condition of dry sliding friction

    利用光學顯微鏡、掃描電子顯微鏡、電子探針以及x -射線衍射儀，分析了表面復合層的基體組織結構；運用反應熱力學、動力學、粉末燒結理論和燃燒合成理論，結合差熱分析結果，探討了表面復合層壓坯的燒結緻密化原理和碳化物增強相的形成機理；利用坯塊在真空燒結爐不同溫度下的燒結出來的顯微組織分析，模擬出坯塊的燒結過程中的化學反應過程。
  17. Kinetics of 8 " phase precipitation and influence of electric field applying during solution process are studied by differential scanning calorimetry ( dsc ) technique

    以示差量熱分析技術（ dsc ）研究相析出的動力學及固溶電場的影響。
  18. In this paper, the property difference of sio2 sols used for preparing thin films by esam method or sol - gel process has been discussed. three kinds of sio2 sols were prepared, catalyzed by hcl or nh3 h2o only, or hcl first and then nh3 h2o respectively ( please note : in following text, the sio2 sol catalyzed by hc1 first and then nh3 h2o and its correspondent films will be named sio2 sol 1 # and film 1 ; the sio2 sol catalyzed by nh3 h2o only and its correspondent films will be named sio2 sol 2 # and film 2 # ). through investigating the assembling properties of the sols, observing thin films " microscopic structure with tem and testing their transmissivity with 721 spectrophotometer, we find that the first kind of sol is not suitable for preparing esam films, but the last two, i. e. sol 1 # and sol 2 #, are good

    本文討論了esam法制備薄膜所用的溶膠與sol - gel法所用的溶膠在性能上的區別，在hc1或nh _ ? h _ 2o分別單獨催化和hc1 nh _ 3 ? h _ 2o分步催化三種催化條件下制備了sio _ 2溶膠（以下規定hc1 nh _ 3 ? h _ 2o分步催化的sio _ 2溶膠為1 ~ #溶膠，相應的薄膜為1 ~ #薄膜， nh _ 3 ? h _ 2o催化的sio _ 2溶膠為2 ~ #溶膠、相應的薄膜為2 ~ #薄膜） ，在通過組裝薄膜並用透射電鏡（ tem ）觀察薄膜微觀結構以及用721分光光度計測試樣品的光透射率，得出了后兩種催化方法所制備的溶膠適合於esam法鍍膜，而第一種溶膠不適于用此法鍍膜的結論，用傅立葉紅外光譜（ ft - ir ）研究了溶膠組成；用差熱失重分析儀（ dta - tg ）對膠體進行了熱分析。
  19. Salt alginate fiber was prepared by means of wet spinning, the structure and properties of the fibers were studied by differential thermal analysis, infrared and scanning electron microscopy

    摘要採用溶液紡絲的方法制備了海藻酸鹽纖維，藉助熱分析、紅外分析及掃描電子顯微鏡等對纖維結構與性能進行了研究。
  20. The system read the bank, use data to draw or insert autocad blocks to design

    固態繼電器結構的熱分析系統是基於ansys的二次開發系統。
分享友人
分享到 Line

分享到臉書