電燈負載 的英文怎麼說

中文拼音 [diàndēngfùzǎi]
電燈負載 英文
lamp load
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 燈 : 名詞1. （照明等用的發光器具） lamp; lantern; light 2. （燃燒液體或氣體用來對別的東西加熱的器具） burner 3. （俗稱電子管） valve; tube
  • 負 : Ⅰ名詞1 （負擔） burden; load 2 （虧損） loss 3 （失敗） defeat Ⅱ動詞1 [書面語] （背） carry on th...
  • 載 : 載Ⅰ名詞（年） year : 一年半載 six to twelve months; six months to a year; 三年五載 three to five ...
  • 電燈 : [電學] electric lamp; electric light電燈插頭 lamp plug; 電燈電流 lamp current; 電燈電路 lighting ...
  • 負載 : [電學] load
  1. As a mix - mode chip, the application - specific controller including analog signal and digital signal processing block can be applied to receiving, amplifying, processing, controlling signals of pir, and offer a wide application in some fields. in analog circuits, by sub - threshold mosfet, a self - bias current source is presented, which has a high power supply restrain ratio and a complementary to absolute temperature characters

    這款晶元是一款數模混合晶元，包括模擬信號處理（含模數介面模塊）和數字信號處理兩大模塊，完整實現對紅外信號的接收、放大、處理、控制，產生有效數字電平驅動繼電器、可控硅等負載，應用於自動燈等多種場合。
  2. Ssr - dd series of dc solid relay is vastly applied to output joggle of computer and external equipments, it is also applied to control or switch dc load : dc relay 、 contactor 、 dc electrical motor 、 kinds of electric - heating apparatus 、 dc electromagnetic valve 、 electromagnetic iron 、 solenoid 、 filament lamp 、 indication lamp 、 plc logical electrical appliance and dc solid relay

    Dd系列直流固態繼電器廣泛應用於計算機與外部設備的輸出介面，適用與控制或開關直流負載：直流繼電，接觸器、直流電動機、各類電熱器具；直流電磁閥，電磁鐵、螺線管、白熾燈、指示燈； plc邏輯電器。
  3. Some common nonlinear loads are fluorescent lighting, scr motor starters and ups systems

    一些常見的非線性負載有熒光燈、可控硅電動機啟動器以及ups系統。
  4. Energy consume, electric strength, insulation resistance, ground conductivity, leakage current, microwave leakage, power input, normal temperature, humidity treatment, glow wire, horizontal flame, vertical flame, tracking, ball pressure, rainproof, water splash, dustproof, salt fog, endurance, motor load test, cord flexing, cord pulling, pull & torque test, lamp replacement, construction check etc

    能耗、電氣強度、絕緣電阻、接地連續性、泄漏電流、微波泄漏、功率、溫升、濕熱試驗、灼熱絲、水平燃燒、垂直燃燒、漏電起痕、球壓試驗、防雨淋、防濺水、粉塵、鹽霧、耐久性（壽命）試驗、電機負載試驗、電源線彎折、電源線提拉、拉扭力測試、燈頭互換性、安全結構檢查等。
  5. Red led flash to indicate the load exceed the current limit and the protecting function start

    紅燈閃爍，表示過負載，使用電流超過額定設定，主機保護機制開啟。
  6. In fact, the electronic ballast is also a kind of power supply converter, but, because of the especial requirement of the hid lamps for electronic ballast, the design of it is very complex

    電子鎮流器實際上是一種電源變換裝置，由於hid燈負載對電子鎮流器的特殊要求而增加了其設計的復雜性。
  7. The control circuit built with conventional analog control is unavoidably cumbersome, the digital control method can simplify the design of circuit, and can satisfy the requirement of the lamps well

    傳統的模擬控制往往顯得麻煩且復雜，數字控制能夠簡化電路設計，並且可以使其更好地滿足燈負載的要求。
  8. The ups shuts down and will not transfer to the bypass mode when a short circuit occurs on output of the unit. after the short circuit being removed the ups will operate normally again. at short condiion, the fault led lights as a warning to end users

    當負載發生短路時，本系統自動關機，並不轉換至旁路，待短路解除后自動恢復供電，在短路情況，故障燈亮同時發出長鳴，警告使用者
分享友人
分享到 Line

分享到臉書