電驅電流 的英文怎麼說
中文拼音 [diànqūdiànliú]
電驅電流
英文
armature current- 電 : Ⅰ名詞1 (有電荷存在和電荷變化的現象) electricity 2 (電報) telegram; cable Ⅱ動詞1 (觸電) give...
- 驅 : 動詞1. (趕) drive (a horse, car, etc. ) 2. (快跑) run quickly 3. (趕走) expel; disperse
- 流 : Ⅰ動1 (液體移動; 流動) flow 2 (移動不定) drift; move; wander 3 (流傳; 傳播) spread 4 (向壞...
- 電流 : current; galvanic current; electric current; electricity; current flow電流保護裝置 current protec...
-
A white led driver circuit is presented in this paper. the circuit drives up to four white leds with regulated constant current for uniform intensity. by utilizing proprietary adaptive 1x / 1. 5x modes and ultra - low - dropout current regulators, it maintains the highest possible efficiency over the full 1 - cell li + battery input voltage range
整體電路以恆定電流驅動4隻白光led ,利用1倍/ 1 . 5倍分數型電荷泵和低壓差電流調節器,在整個鋰電池供電電壓范圍內保持最高的效率,並使四個白光led獲得均勻的亮度。This paper presents a method that chopping wave is done by switch devices which consist of three - level resistance regulating module and intelligence power module ipm, and which realizes constant - current discharge of storage battery. to achieve the intelligence control of the drive protection and the discharge process of ipm, the paper designs circuit formed by igbt threshold drive pulse pwm signals. ipm fault - blocking protection circuit and microcomputer 80c196. the devices can accurately control the 0 ~ 150a discharge current and the discharge time of the storage battery and calculate the releasing power
實現蓄電池恆流放電過程智能控制是蓄電池放電裝置發展的必然趨,本文提出了一種通過三極電阻調節模塊和由智能功率模塊ipm為開關器件進行斬波從而實現蓄電池恆流放電的方法。為達到對ipm的驅動保護和放電過程的智能控制,文中設計了igbt門極驅動脈沖pwm信號形成電路和ipm故障封鎖保護電路及由單片機80c196為核心的微機控制器。本裝置能夠對蓄電池進行0 150a放電電流及放電時間的精確控制及釋放容量的計算。Low voltage driving is available without inverter
低電壓支流驅動,不需要逆變器The outside of this chip adopts boost structure to drive up to seven white leds with the input voltage ranging from 3v to 5v. series connection of the leds provides identical led current resulting in uniform brightness
電路的電源輸入在3v 5v變化,採用boost電路結構升壓,在極限情況下最多可驅動七個白光led ,由於led串聯,因此各led電流完全匹配,亮度一至。They are widely used in many fields such as telecommunications, finance, traffic, gymnasium etc. led drivers are necessary in the application of led displays. they can supply constant output current and make the led light even, and also can make the led ’ s life longer
Led顯示屏的應用離不開它所需要的驅動控制電路,通過驅動電路來獲得良好而平穩的電流,使led顯示更加均勻,滿足各種場合的應用要求,同時可以延長led的使用壽命。Many planets ( for example, ganymede, mercury, the earth, jupiter and saturn ) and stars ( for example, the sun ) possess intrinsic magnetic fields. the explanation for their existence and variation remains a great challenge to planetary scientists and astrophysicists. this article attempts to review some recent developments and difficulties in the study of magnetohydrodynamics for the electrically conducting fluid interiors of planets and stars. it is the fluid motions, usually driven by thermal convection, that generate and sustain magnetic fields through magnetohydrodynamic processes in planets and stars. in planets, the magnetohydrodynamic processes are strongly affected by the combined and inseparable effects of rotation, magnetic fields and spherical geometry. the key dynamics involves the interaction between the coriolis and lorentz forces. in the sun, it is the solar tachocline, a thin shear flow layer located at the base of the convection envelope, that plays an essential role in the solar magnetohydrodynamic processes which produce the 11 - year sunspot cycle. some results of a new nonlinear three - dimensional solar dynamo model are also presented
許多行星(如木衛三,水星,地球,木星和土星)和恆星(如太陽)具有內部磁場.對這些磁場的存在和變化的解釋對行星科學家和天體物理學家是一個巨大的挑戰.本文試圖總結行星和恆星的導電流體內部磁流體力學研究的新近發展和困難.一般由熱對流驅動的流動通過磁流體力學過程產生並維持在行星和恆星中的磁場.在行星中磁流體力學過程強烈地受到轉動,磁場和球幾何位型的綜合影響.其動力學的關鍵方面涉及科里奧利力和洛倫茲力間的相互作用.在太陽中其流線,即處于對流層的薄的剪切流層在太陽的磁流體力學過程中扮演了一個基本的角色,並由之產生了11年的太陽黑子周期.本文也給出了一個新的非線性三維太陽發電機模型Since a pentode presents a fairly constant current sink, trying to power it from a constant current source will be fairly unsuccessful, sort of like the unstoppable object hitting the immovable object
因為五級管本身就表現得類似恆流陷阱(意思是消耗恆定的電流) ,試圖用恆流源驅動五級管只會是個失敗,就好像試圖用一個停不下來的物體去打擊一個不可移動的物體。In this article, physical equations and relative three - dimensional finite - difference formulae in cylindrical and spherical geometries were derived and two - and three - dimensional code in cylindrical and spherical geometries for direct - drive by laser was made, based on the lared - s code in planar geometry. it consisted of the processes such as the inverse bremsstrahlung absorption, electic heat conduction and fluid dynamics
本論文在lared - s程序平面版本基礎上,推導了三維柱和球幾何中激光驅動的物理方程和相應的差分方程,編制了二維和三維柱和球幾何中激光驅動流體不穩定性的lared - s程序版本,主要物理過程包括:激光逆軔致吸收、電子熱傳導和流體運動。This strategy effectively solves the power distribution between the apu and batteries during the drive of the heb. the power control model and multi - torque switching strategy of the driving motors control the charging - recharging current of the batteries within a wide range, which contribute to the improvement of the efficiency
該策略很好的解決了車輛行駛時輔助動力系統與蓄電池組之間的功率分配,並且驅動電動機採用功率控制模式以及多級動力輸出切換策略,有效的控制了蓄電池的充放電電流,從而提高了整車效率。This paper presents our research in actuating in - vivo micro - robot based on the capsule endoscope platform by the external power. while seeking secure driving method we take several factors into account, such as driving environment, power transmitting and consuming, motion requirement and controllability, and locating technique. we mainly deal with driving the capsule with spatial gradient magnetic field, so we employ combined electro - magnetic coils, including gradient coils and homogenous coils, which have rotational dof around a translatable patient bed, to compose a controllable uniform gradient which act on the permanent - magnet embedded robot, thereby get an appropriate spatial force and torque to fulfill the anticipant locomotion such as move, stop, pitch and yaw
基於驅動環境、能量供給和消耗、驅動動作要求及驅動安全性與可控性,定位方案等多方面考慮,尋求安全可靠的腸胃檢查微機器人的外部驅動控制方法,並著重研究直接利用外磁場磁力驅動微機器人:在微機器人內部嵌入永磁性體,利用體外的組合電磁線圈產生加載電流控制的驅動磁場,其中外部的電磁線圈由多組梯度線圈和勻場線圈組合構成,通過繞病床的旋轉以及病床的平移共同控制微機器人所在位置的磁場強度及梯度,作用於微機器人內嵌磁體以獲得空間意義上的必要驅動力和調整轉矩,從而有效地完成驅動動作要求。To solve the problems above, this dissertation supported by the project of national natural science foundation ( nnsf ) : research on piezoceramic micro - actuator ’ s polarity modeling and controlling method ( code : 60274053 ) focuses on the research of driving and control technique of piezoceramic. the drivers based on voltage, current control had been designed with the high voltage amplifier as core component
針對壓電陶瓷驅動存在的上述問題,本文結合國家自然基金項目「壓電陶瓷微驅動器件極化模型與驅動方法的研究」 (編號: 60274053 ) ,以高壓運算放大器為核心元件,通過分析電壓、電流型驅動器原理及電路參數,提出了一種彌補其不足的復合型驅動方法。Vvvf door controller frequency converter makes lift door installation easier and more convenient as its control center is the internationally advanced engineering 16 digital micro computer and it operates with the fully digital spwm modulation techniques, with igbt module as the output power drive and with voltage, current and speed under fully digital closed circuit control ( the door controller ' s operation parameters are inputted by means of the keyboard )
Vvvf控制門機變頻器採用當今國際上先進的工控16位微型計算機為控制核心,採用了全數字spwm調制技術, igbt模塊作輸出功率驅動,電壓、電流、速度全數字閉環控制(門機的運行參數均可通過鍵盤設置輸入) ,從而,使門機的安裝調試更加簡單,方便。The main circuit is consisted of 18 thyristors circuit and protection circuit. with the help of control subsystem, it can get the output of low frequency voltage ( current ) with the shape of sine wave ; the core of the control subsystem is the cpu of 87c196kc, and the synchronization circuit, the pulse - widen circuit, and the power - enlarged circuit form the accessorial subsystem of the control system. it possesses all the functions of digital triggering, digital tuning, analog / digital conversion ; the input transfer can isolate the input and output ; and the circumfluence reactor can reduce the circumfluence
主迴路採用由18個晶閘管組成的三相零式電路,並輔以晶閘管的保護電路,通過控制可以得到低頻正弦波的電壓(電流)輸出;控制迴路主要以87c196kccpu為核心,其外圍電路包括同步電路,脈沖拓寬電路,功率放大驅動電路等,完成了數字觸發、數字調節、模數轉換等功能;進線電源變壓器具有變壓和隔離作用;環流電抗器則實現了有效抑制主迴路瞬時脈動環流的功能。Then the paper analyzes control system of hybrid active power filter, the way of harmonic detecting and the principle of control system, digital low pass filter and the generation of pwm, on the base of which the paper designs a new parallel hybrid active power filter which is controlled by tms320lf2407, and detailedly introduces drive circuit of pwm, sampling circuit of current, voltage adjustment and protection circuit, communication circuit, liquid crystal display circuit
分析了混合型有源濾波器的控制系統、諧波檢測方法及控制原理、數字低通濾波器和pwm信號的產生,在此基礎上設計了一種基於tms320lf2407為控制核心的並聯混合型有源電力濾波器硬體原理圖。並對pwm驅動電路、電流采樣電路、電壓調整、按鍵輸入和保護電路、通信模塊、液晶顯示模塊進行了較詳細的分析說明。However, df pre - processing is not required in a interferometer direction finder. it only makes use of the phase relations or differences of sensors disposed at different position. azimuth and elevation are caculated from the phase differences or displayed directly on a crt drived by the voltage or current from the phase differences
干涉儀測向不必進行測向信號預處理而是直接或間接求取在空間上分開的傳感器上感應電勢之間的相位關系,即干涉相位差,方位角或仰角是直接由干涉相位差計算得到,或將兩基線正交的天線陣的干涉相位差轉化為驅動電壓(電流)分別加到crt陰極顯示器的垂直偏轉線圈和水平偏轉線圈,模擬顯示出來波方位,干涉儀測向為典型的相位測向方法。Based on studying of the multi - level technique, a variable frequency speed regulation system based on the diode clamped three - level inverter is introduced in this thesis in detail. it includes ac - dc - ac main power circuit, snubber circuit, isolated driving circuit by optical fibre, delay time circuit on powering, sampling circuit of current and voltage, protection circuit and etc. a distributed power system ( dps ) which can reinforced the system ’ s security is developed to solve the power supply of the whole system
本文在研究多電平技術的基礎上,研製了一套以二極體箝位式三電平逆變器為基礎的變頻調速系統,包括:交-直-交主功率電路,緩沖電路,光纖隔離驅動電路,上電緩沖延時電路,電流、電壓采樣電路,保護電路等。By deeply analyzing the reason of the fault and optimizing the parameter of circuit, performance of drivers increased greatly and a new way based on compound driving had been proposed which reduce the fault of traditional driver
通過電路分析,研製了電壓、電流及復合控制型壓電陶瓷驅動器。並通過優化電路參數,在其他性能指標不降的情況下提高了原電壓及電流型驅動器的動態性能。With the mathematics models of the lithium ion battery and ac motor, the approach and magnitude of energy consume of the whole vehicle are analyzed under the conventional theory of automobile in this paper. at the same time, the relation between the energy consume and the charge and discharge voltage and current of the battery, as well as that between the energy consume and the voltage and current of the motor stator are made clear on the basis of ece drive mode
文章從傳統的汽車理論出發,結合鋰離子動力電池和電機的數學模型,分析了純電動汽車整車的能量消耗途徑和大小;基於歐洲ece循環驅動模式,建立了純電動汽車的功率消耗與電池的充放電電壓、電流以及電機定子電壓、電流之間的關系,並在此基礎上分析了純電動汽車的續駛里程和制動能量的回收問題。In addition, according to the need of sampling of voltage and reactive - power control system in windows 98 / 2000, the method of using windows driver model is presented to realize the sampling of the voltage and the current, and the program of windows driver model is provided in this thesis
另外,文中還分析了電壓無功控制系統中采樣的要求,根據windows環境下實現高頻率采樣系統的要求,提出了利用wdm實現電壓無功控制系統中的電壓電流采樣的方法,並給出了wdm驅動程序的實現。The controller based on nec pd78365 using in motor for special purpose checking circuit for voltage and current igbt driving circuit protection circuit have been developed, also the detail software flow charts are shown
設計了基於nec pd78365電機專用cpu的變頻微機控制器、電壓,電流檢測電路, igbt驅動電路和保護電路,並給出了詳細的軟體流程圖。分享友人