霧化式噴嘴 的英文怎麼說

中文拼音 [wùhuàshìpēnzuǐ]
霧化式噴嘴 英文
atomized spray injector
  • 霧 : 名詞1. （水蒸氣凝結成的小水點） fog 2. （像霧的許多小水點） fine spray
  • 式 : 名詞1 （樣式） type; style 2 （格式） pattern; form 3 （儀式; 典禮） ceremony; ritual 4 （自然科...
  • 噴 : 噴動詞1. （液體等受壓力而射出） spurt; spout; gush; jet 2. （噴灑） spray; sprinkle
  • 嘴 : 名詞1. （口的通稱） mouth 2. （形狀或作用像嘴的東西） anything shaped or functioning like a mouth 3. （指說話） talk; speak
  1. Performance of y - type airblast nozzle in solvent - removing process of chlorination liquid

    型氣流式噴嘴的霧化性能
  2. This " paper mainly researches on the humidifying property of the centrifugal nozzle with firing pin type, high pressure and little aperture

    課題主要對撞針型高壓小孔徑離心式噴嘴的霧化加濕性能進行研究。
  3. As to the work about theory analysis, at first, the paper describes the atomizing and humidifying process of the centrifugal nozzle with firing pin type, high pressure and little aperture and liquid physical properties. later, combining with the structure characters of this kind of nozzle, the paper studies on the theory of the atomizing and humidifying process by three phases, which is water film forming phase, water film falling into pieces phase, and heat and mass transfer between water and air phase in turn

    理論工作方面，首先描述了撞針型高壓小孔徑離心式噴嘴的霧化加濕過程和液體的物理性質，然後結合撞針型高壓小孔徑離心式噴嘴的結構特點，將其霧化加濕過程分三個階段進行機理上的研究，這三個階段依次為液膜形成、液膜初次破碎及二次霧化、水與空氣的熱濕交換。
  4. Based on the theory analysis and experiment work, the paper studies the humidifying property of the centrifugal nozzle with firing pin type, high pressure and little aperture. compared with the traditional air washer, the high efficiency and energy saving character of this kind of nozzle is stood out

    課題從理論和試驗兩方面分析研究了撞針型高壓小孔徑離心式噴嘴的霧化加濕性能，並將其與傳統噴水室加濕系統進行能耗比較，突出了撞針型高壓小孔徑離心式噴嘴高效節能的特點。
  5. Through the special studies on impacts to atomizing and humidifying effect from such factors as the firing pin type, centrifugal structure, higher spraying pressure, less aperture, initial water temperature and original state of the air, some conclusions are obtained, such as : the centrifugal nozzle with firing pin type, high pressure and little aperture has bigger air eddy and atomizing angle. the spaying liquid has high velocity. the droplet is small, and the heat and mass transfer velocity is high

    通過對撞針型結構、離心式結構、較高的噴水壓力、較小的噴嘴孔徑、噴水初溫及待加濕空氣初狀態對霧化加濕效果的作用原理的重點分析，得到：撞針型高壓小孔徑離心式噴嘴具有較大的空氣渦與霧化角，噴出的液體流速高、液滴小、水與空氣傳熱傳質速率高，撞針型結構提高了霧化加濕效率，高壓小孔徑的特點為霧化加濕提供了較大的能量，而噴水初溫的升高會減小水的粘性力和表面張力，從而優化加濕效果。
  6. Integrated the work on theory and experiment, the paper provides technical performance material at large about the automating and humidifying character of the centrifugal nozzle with firing pin type, high pressure and little aperture to the manufacture and user. with the valuable reference during the selecting the equipment and ascertaining the parameters, the users could select and control the humid parameter

    課題的理論與試驗兩方面工作相結合，為撞針型高壓小孔徑離心式噴嘴的霧化加濕性能提供了較為詳細的技術性能資料，為生產廠家和用戶在設備選型和參數選擇過程中，提供了有價值的參考，便於用戶正確而經濟地選擇、控制濕度參數，有效調節噴嘴孔徑、噴水初溫和噴水壓力的大小。
  7. Ultrasonic has being attracted much attention gradually in fuel atomization because of some specialities of cavitation and infection on liquid flow. in the course of atomization of pitchy oil, especially, does it show greatly its advantage, but its material atomizational mechanism need research ulteriorly. the primary content of this thesis is about adding cantilever reed to effervescent atomizer so as to combine ultrasonic and effervescent. this thesis has discussed ultrasonic some mechanism, ultrasonic dynamical procreator, effervescent and liquid mucosity infection on atomization, at the some time we make some experiments and discuss atomization rule following some machinery parameter and run parameter so as to find some rule about ultrasonic atomization and to rich the research of ultrasonic atomization mechanism. all that will be beneficial to the design about ultrasonic atomization atomizer

    超聲波由於其空化機理及對液體的流變性影響等特性，在燃油霧化燃燒中逐步引起人們的重視，尤其在重渣油等高粘度液體的霧化過程中逐步顯示出其優越性，但其具體的霧化機理還需要做進一步的研究在氣泡霧化噴嘴基礎加入懸臂式簧片哨，將超聲波與氣泡霧化相結合是本文討論的主要內容本文從研究超聲波的一些機理入手，討論了超聲動力發生器氣泡霧化以及液體粘度對霧化質量的影響，並通過具體的實驗，根據實驗數據來討論霧化質量隨各種結構參數運行參數的變化規律，以便找到超聲霧化的一些規律，豐富對超聲霧化機理的研究，對超聲霧化噴嘴的設計具有一定的指導意義。
  8. Strong and high effective mixing of swzzero gravity particle mixer can meet your demand. two mixing axles make a equal speed and reverse rotation in horizontal tube. oars on mixing axle make the materials do radial motion, circular motion and axial motion. in a short time, the particle can be stirred homoginously. nozzel on cover of tube can be used when the solid is mixed with liquid

    無重力粒子混合機（以下簡稱無重力）以強烈、高效混合而來滿足用戶需求，臥式筒體內兩根攪拌軸等速反向旋轉，攪拌軸等速反旋轉，攪攔軸上特殊布置的漿葉確保物料徑向、環向、軸向三向運動，形成復合循環，在極短的時間內達到均勻混合，筒蓋上布置霧化噴嘴供你固液混合時使用。
  9. Focusing on the performance evaluating and the design of tripropellant injector, adopting the cold test rig with background pressure supply, malvem particle analyzer, ccd photography system, tripropellant hot test - bed, numerical simulation software and auxiliary theoretical a nalysis, the d ischarge c haracteristic a s w ell a s a tomization p erformance o f the injector and the combustion performance as well as the mode - transition characteristic of thrust chamber are studied detailedly based on the 3 different structures of coaxial tripropellant injector, large numbers of important conclusions are gained

    本文圍繞三組元噴嘴的性能評定及設計方法。採用反壓冷試臺、馬爾文測粒儀、 ccd高速攝影系統、三組元發動機熱態試驗臺、數值模擬程序及輔助理論分析等多種技術手段和研究方法，對三種結構的同軸式三組元噴嘴深入進行了噴嘴流量特性和霧化特性、推力室燃燒性能和轉工況性能研究，得到了大量重要結果。
  10. Based on the induction phenomenon caused in gas hydrate formation, the influential rules of its gas entrance mode, temperature, pressure, water resources and nozzle on the induction time are analyzed by means of experimental study on the induction time of gas hydrate formation obtained by water spray and enhancement

    摘要以氣體水合物形成過程中的誘導現象為基礎，通過對噴霧強化方式制取天然氣水合物的誘導時間進行試驗研究，考察分析了系統進氣方式、溫度、壓力、水源及噴嘴等因素對誘導時間的影響規律。
  11. Its atomized parcel is so small that no drip is separated out. this kind of centrifugal nozzle has high humidifying efficiency and low energy cost, which could be used in many situations in textile factories such as directly humidifying in workshop and humidifying in air pipeline

    撞針型高壓小孔徑離心式噴嘴的霧化粒子細小、無水滴析出、加濕效率高、耗能少，可直接向車間加濕，適用於紡織廠等多種應用場合。
  12. As to the work about experiment study, at first, the paper makes certain the prominent affecting factors to the automating and humidifying property of this kind of nozzle by orthogonal experiment. by jicha analysis method and fangcha analysis method, the paper got that the nozzle aperture, the initial water temperature and the spraying pressure have prominent effect to the humidifying property while the effect of the original air state is small

    試驗工作方面，首先通過正交試驗確定對撞針型高壓小孔徑離心式噴嘴霧化加濕性能影響顯著的因素，運用極差分析法和方差分析法，得到噴嘴孔徑、噴水初溫和噴水壓力對噴嘴的加濕性能影響顯著，而待加濕空氣初狀態的影響相對較小。
  13. Using compressed air and transformer oil as working substance, this paper studied the pressure characteristic of internal - mixing nozzle and acquired the experimental relation on the pressure in the mixing chamber of internal - mixing nozzle against the operation parameters and structure parameters according to the method of step by step regression

    摘要以壓縮空氣和變壓器油為工質對內混式介質霧化油噴嘴的流量特性進行實驗研究，並通過逐步回歸分析的方法獲得了內混式介質霧化噴嘴油、氣流量系數與運行及結構參數的實驗關系式，可供設計使用部門參考。
  14. The dehydration time is square of the droplets diameter so the small diameters of the droplets can cut down the drying time then reduce the height of the drying chamber. to the combined spin - flow pressure spray drying, the diameters of droplets are small and the dehydration rate is higher so keeping the qualities of the dried products we can increase the speed of the inlet wind and reduce the temperature of the outlet wind thus can improve the evaporation intensity of the drying chamber and the average energy utilization of the drying equipment

    因霧滴的脫水時間與其直徑的平方成正比，減小液滴直徑有利於縮短乾燥脫水時間，可有效降低乾燥塔的高度；由於旋流式組合壓力噴嘴霧化滴徑的減小，脫水速度明顯加快，在不影響乾燥物料性質的前提下，適當提高進風溫度，同時有效地降低排氣溫度，有利於提高幹燥塔的蒸發強度，也有利於提高幹燥設備的平均能源利用率。
  15. Using swirl atomizer designed by this paper, kerosene was injected into the ejector combustor, and achieved steady combustion. this made a solid foundation for the future study on combustion organization

    設計了旋流式霧化噴嘴，實現了煤油在引射火箭模態中的穩定燃燒，為進一步的燃燒組織研究奠定了基礎。
  16. Experiment shows that when the gas hydrate is obtained by spray, its induction time is generally shorter, its phenomenon is not obvious, setting of initial temperature and pressure with an autoclave has certain influence on induction time, but not obvious, water resources and spray nozzle have bigger influence on the induction time

    試驗表明，噴霧方式制取天然氣水合物時，誘導時間普遍較短，誘導現象不明顯；反應釜設定初始溫度和壓力對誘導時間有一定影響，但不是很明顯；水源和霧化噴嘴對誘導時間的影響較大。
  17. This type of dryer was fitful for liquid drying in concurrent, counter - current or mixed air - flow. the dryer can produce powders, granules, hollow spherical particles and agglomerates products. the spraying capacity and particle size were changed by altering the parts assembled in the nozzle

    壓力噴霧乾燥裝置其霧化器的結構適用易調，可通過改變噴嘴的內部結構得到所需要的噴液量和霧滴尺寸，目前該型式乾燥機已推廣應用於食品、化工、醫藥、建材、環保等行業。
  18. 1. instead of old inner - mixed vortex nozzles, improved y - type nozzle is developed. the designing calculation of new nozzle and corresponding air distributed organ are made, and the atomization effect is verified and compared with old one

    對原內混式旋流型噴油嘴進行改造，改用y型噴嘴，進行了噴嘴改造的設計計算和相應配風器的改造設計計算，比較和校核了其霧化效果。
  19. ( 2 ) base on the analysis of the atomizing principles of spray nozzle, mathematical model of combined spin - flow pressure spray drying was set up and the essential parameters such as spraying pressure, liquid quantity, temperature, spraying angle, inject distance, particle diameter and distribution, hollow diameter for several materials in normal conditions by experiment and ldv

    （ 2 ）對旋流式組合壓力噴嘴噴射霧化機理加以分析，建立了旋流式噴嘴霧化的數學模型，採用冷態試驗法並藉助激光霧滴測試等實驗裝置對噴嘴的霧化參數（如霧化壓力、噴液量、料液溫度、霧化角、霧距、霧滴直徑和分佈以及噴嘴的空芯半徑等）進行測量和計算。
  20. ( 4 ) the droplets diameter of the combined spin - flow pressure spray drying are between 30um and 150um and the ranges of the droplets are narrow. the average diameter of the droplets is between 50 um and 100 um and the spraying angle can be adjusted from 30 to 180

    （ 4 ）採用旋流式組合壓力噴嘴霧化后的液滴直徑大都分佈在30 150um之間，霧滴分佈范圍較窄，其霧化的平均液滴直徑在50 100um左右，壓力噴嘴的霧化角度可在150 180范圍內。
分享友人
分享到 Line

分享到臉書