霧化錐 的英文怎麼說
中文拼音 [wùhuàzhuī]
霧化錐
英文
atomizer （atomizing） cone-
With gelatin liquor as adhesive and wheat meal as granulation material, the effects on spray granule ' s strength of fluidizing gas velocity, bed temperature, nozzle air pressure and adhesive concentration were studied experimentally in a batch conical fluidized bed spray particle generator
本文在一間歇錐形流化床噴霧造粒器中，以食用小麥澱粉為原料，以明膠的水溶液為粘結劑，實驗研究了流化氣速、床層溫度、噴嘴霧化空氣壓力、粘結劑濃度對噴霧造粒顆粒強度的影響。According to the experimental data of droplet size 、 particle spectrum range 、 droplet cone shape 、 flow rate 、 cover area and cover area rate which obtained through changing the pressure of power sprayer and the nozzle diameter in greenhouse ， this paper made comparative analysis on atomizing performance in same pressure and different nozzle type between same nozzle type and different pressure. the conclusion is that : the ejection rate and the droplet cone shape change with the variation of pressure and nozzle diameter ， average particle diameter decreases obviously and particle quantity increases obviously with the increase of pressure and decrease of nozzle diameter. these results will lay experimental foundation for precise spraying 、 low pollution and highly effective operation
本文根據溫室內動力噴霧機壓力與噴嘴孔徑的變化影響霧滴大小、粒譜范圍、霧錐形狀、流量、覆蓋面積及覆蓋面積率的試驗數據，對相同壓力下不同噴嘴型號和相同噴嘴型號時壓力不同時的微粒化性能進行對比分析和研究，得到如下結論噴出量與霧錐形狀隨著壓力和噴嘴孔徑大小變化而變化；平均粒徑隨著壓力的增加和噴嘴孔徑的減小而明顯減小；粒數隨著壓力的增加和噴嘴孔徑的減小而明顯增多，為精噴量、低污染、高防效的防除作業奠定了實驗基礎。( 3 ) the most principal factors that influence the supersonic atomization process include the flow ratio of the gas - liquid metal ( gmr ) value, the flow of atomizing of gas and the range of the inverse vortex taper. the more of the value of three factors, the more advantage they are for the atomization and the more fine the powders are. ( 4 ) the produced powders are the best in efficient atomization efficiency, particle diameter, particle shape and dispersion when the solder alloy is zhl63a, atomizing medium is n2, the protrusion h = 6. 0mm, atomizing gas pressure p = 100mpa, over - heat temperature t = 167 ( t = 350 )
研究結果表明： （ 1 ）超音速霧化器的氣體流場在導液管下端形成一個倒渦流錐，在二維空間上呈軸對稱的雙峰分佈，負壓形成於這個倒渦流錐內； （ 2 ）修正後的霧化氣體速度公式可以滿足超音速霧化的要求； （ 3 ）影響超音速霧化工藝最根本的因素有氣液質量流率比（ gmr ）的大小、霧化氣體流量和倒渦流錐范圍，三個因素的值越大，對形成細粉越有利； （ 4 ）在焊錫合金為zhl63a ，霧化介質微n _ 2 ，導液管突出高度取h = 6 . 0mm ，霧化氣體壓力取p = 1 . 0mpa ，合金過熱度取t = 167 （ t = 350 ）時，所制得的粉末在有效霧化率、顆粒球形度、粒度及其離散度三個方面綜合性能最好。The conclusions are as follows : ( 1 ) high - pressure water - atomization can be used to produce a pre - alloyed steel powder with high apparent density, high green strength, size - stability after sintering and low hydrogen - loss content ; ( 2 ) the higher smelting temperature and / or water pressure, the finer particle size of steel powders ; ( 3 ) when the atomization angle holds in a reasonable value ' s range the obtained powder will have a better particle size distribution ; ( 4 ) an optimum atomization technological parameters : liquid steel flux, water pressure and water prick angle was obtained ( 5 ) reduction variables ( temperature, holding time, material - bed ' s thickness and reducing gas flux ) have a significant effect on the particle agglomeration and properties of final powder was given ( 6 ) different alloying methods were developed to modify properties of ferrous powder materials and hence to broaden its applications in ferrous powder metallurgy industry
本文系統研究了水霧化預合金鋼粉生產工藝及合金化方法對鐵基粉末冶金材料性能影響，詳細研究了冶煉、霧化、還原工藝參數對預合金鋼粉化學成份和物理性能影響，並得出如下結論： （ 1 ）採用高壓水霧化技術可用於生產高密度、高強度、尺寸穩定性的低氫損含量的水霧化預合金鋼粉。 （ 2 ）冶煉溫度越高，高壓水壓力越大，所得生粉顆粒粒度越細。 （ 3 ）水錐角調整在一個適當角度范圍內可獲得粒度組成較好的生粉。This paper reports the droplet size and distribution, penetration and diffusionangle of fuel spray before and after impingement by multiple - picture overlapping photography and laser technology, as well as the fuel spray mixing and burning process in a direct injection diesel engine by high speed photography
本文介紹了用多次噴霧疊加攝影與激光粒子分析技術對燃油噴霧撞擊前後的粒徑、貫穿度以及噴霧錐角等因素變化所進行的觀察和測量以及介紹了利用雙像高速攝影技術對燃油束撞擊霧化形成的混合氣以及燃燒過程特點的研究。分享友人