靜態偏差 的英文怎麼說

中文拼音 [jìngtàipiānchā]
靜態偏差 英文
static deflection
  • 靜 : Ⅰ形容詞1. （安定不動; 平靜） still; calm; motionless 2. （沒有聲響; 清靜） silent; quiet Ⅱ名詞（姓氏） a surname
  • 態 : 名詞1. （形狀; 狀態） form; condition; appearance 2. [物理學] （物質結構的狀態或階段） state 3. [語言學] （一種語法范疇） voice
  • 偏 : Ⅰ形容詞1 （不正; 歪斜） inclined to one side; slanting; leaning 2 （只側重一面） partial; prejudi...
  • 差 : 差Ⅰ名詞1 （不相同; 不相合） difference; dissimilarity 2 （差錯） mistake 3 [數學] （差數） differ...
  • 靜態 : [物理學] static state; quiescent condition; steady state; statics; dead level; akinesis; akynesis...
  1. The paper designed aerodynamic control system of pith and yaw channels and roll angle stabilization system, by using unsteady - state error follow - up control theory and state observation station theory in modern control theory

    本文使用現代控制理論中的無靜差跟蹤控制系統理論與狀態觀測器理論，設計了俯仰、偏航兩個通道的氣動力控制系統和滾轉角穩定系統。
  2. According to these accomplishments, several techniques are expounded emphatically in this paper, including 3d refraction statics, coherent noise suppression by prestack wave field separating ( prestack fx noise attenuation ), 3d prestack multiple domain random noise attenuation, multiples attenuation, nmo of unsymmetrical hyperbola, dynamic replacement of wave equation, surface - inconsistent residual static, super bin stacking, poststack depth migration and prestack depth migration. all the techniques have been applied in seismic processing of 2d, 3d and wide - line profiling and obtained good results

    本文根據項目組研究成果，重點閘述了三維折射波靜校正技術，疊前波場分離相干噪音壓制方法（疊前fx去噪） ，疊前三維多域隨機噪音衰減技術，多次波衰減技術，非對稱雙曲線動校正技術，波動方程動態替換技術，非地表一致性的剩餘時差靜校正技術，超面元迭加處理技術，疊后深度偏移處理，疊前深度偏移處理等。
  3. Through lots of simulation experiment, deeply discuss the structure of the cascade fuzzy control system and get the final project. the simulation experiments state that to import the fuzzy logic controller to the cascade control system can greatly improve the control quality of the cascade control, shorten the settling time and boost up the resistance to the inner loop disturbance

    由於模糊控制器本身存在著較大的靜態偏差，研究中提出了將普通的模糊控制器與積分控制器相結合，利用積分控制器來解決模糊控制器的靜態偏差大的弊病，可以實現良好的控制效果，在大量的模擬實驗基礎上，總結出模糊控制器引入到串級控制系統中的最佳結合方案。
  4. Static characteristics derivation

    靜態特性偏差
  5. Guide to statistical process control charts for variables - charts for mean, median, range and standard deviation

    變量靜態加工控制圖表指南.均值，中值，范圍和標準偏差圖表
  6. A fuzzy control system of stepping motor for seam tracking is presented in this paper, the proposed system can realize the self - modify ing of the parameters and improve the characteristics of dynamic and static state of stepping driving system according to the error of seam tracking. the accuracy of seam tracking is enhanced obvi ously

    介紹一種用於焊縫跟蹤的步進電機模糊控制系統，該系統可根據跟蹤偏差進行參數自調整，改善了步進驅動系統的動靜態特性，提高了焊縫跟蹤精度。
  7. Rectangular bars of wrought nickel and nickel alloys, hot rolled ; dimensions, tolerances, static values

    熱軋變形鎳和鎳合金矩形棒材.尺寸允許偏差靜態值
  8. Cross - country skis. determination of breaking load and deflection at break with quasistatic load

    速度滑雪板.準靜態載荷斷裂條件下斷裂載荷和偏差的測定
  9. A batch least - squares maximum likelihood estimator is employed to calibrate the model coefficients of accelerometer and a polynomial post - fit method is used to establish temperature models of these coefficients. the temperature models of accelerometer bias and scale factor of accelerometer are established between - 20oc and 50 oc. after compensating the temperature error by using these models, the post - fit residuals of the accelerometer output have been improved to 10 ? 5 g, and the trend term of accelerometer changing with temperature basically vanished

    採用最小二乘極大似然估計和多項式擬合的方法，分析加速度計靜態模型系數隨加速度計殼體溫度變化的規律，建立了- 20oc 50oc之間加速度計零偏和標度因數誤差的溫度模型，應用該模型對加速度計溫度干擾進行補償，補償后，加速度計輸出的擬合均方根誤差一到二個數量級，並且基本上消除了加速度計輸出隨溫度變化的趨勢項，使得加速度計測量精度得到了明顯提高。
  10. It has a static yoke. i ' ll double check the draw stop timing. would draw stop timing affect left / right impact

    本來纜索就是靜態卡位的.我想再查看一下偏心輪拉停定位的同步問題.吃不準，拉停定位的同步，是否真的影響到命中點的左右偏差
分享友人
分享到 Line

分享到臉書