靜摩 的英文怎麼說
中文拼音 [jìngmó]
靜摩
英文
shizumaro-
Based on extensive investigation of construction technique history of chinese ancient buildings, the structure method, structure developing history and seismic behavior of chinese ancient timber structure buildings are analyzed in several respects of the structural system and form. through a series of experiments on constituent parts of chinese ancient timber building structure, including the tests on the corbels and brackets called dougong subjected to low cyclic reversed loadings, the tests on the wooden frame using the tenon - mortise joints as connections of column and beam subjected to low cyclic reversed loadings, the tests on vibration isolation effect of friction and slippage between column footing and their socle base, and a series of shaking table tests on a chinese ancient timber structure palace building mode under artificial earthquake at serving conditions, destroyed conditions and reinforced conditions, many valuable results of structures such as moment - curvature hysteretic loops of dougong structure and tenon - mortise joints under low cyckc reversed loadings, the static function, the seismic performance, energy dissipation, vibration reduction, energy - loss mechanism, nechanicalmode and failure mode were studied. aplenty of valuable parameters of the structure system were obtained, such as the natural period of structure, vibration modes, damping ratio, factor of vibration isolation, oscillate amplitude of ineitial accebration, velocity and displacement, magnitude of slippage, and the mechanism of structure failure and collapse etc. based on these research, the complete analysis of ancient timber structure under earthquake were carried out in which including mechanism analysis method, calculating mode, strength analysis of members and joints, strengthening methods for serving damaged ancient timber structure buildings were also taken into account
依照宋代《營造法式》建造了抬梁式殿堂木結構構件及結構模型，對中國古代木結構中的典型構造如：柱腳在礎石頂面平擱簡支、柱架榫卯連接、柱高不越間之廣、側腳、生起、斗拱等的構造機理及結構功能進行了量化分析和實驗研究： （一）通過木柱石礎靜摩擦試驗，測定了柱腳與石礎古鏡面間的摩擦系數及摩擦力隨上部結構荷載變化的規律； （二）通過單柱承載力試驗，測定了古建築中木柱的受力變形特徵、破壞模式、及模型材料的變形模量、極限承載力、極限變形等參量； （三）通過柱架低周反復荷載試驗，測定了柱架的抗側移剛度、柱架恢復力特性及滯回曲線、榫卯張角剛度及其變化規律、柱架及榫卯的極限承載力和極限變形、及榫卯減振參數； （四）通過斗?低周反復荷載試驗和受壓試驗，測定了古建築木構件與木構件間摩擦系數，斗?抗側移剛度，斗?恢復力特性及滯回曲線，斗?抗壓極限承載力及受力變形規律； （五）通過抬梁式殿堂間架模型振動臺試驗，測定了殿堂木構架結構自振周期，地震反應振形、阻尼特性及阻尼比；按結構分層特點對柱腳、柱頭和斗?層上的屋蓋的地震反應採用多點同步測量，對柱根滑移、榫卯變形、斗?的變形、復位、耗能減振參數等進行了定量分析。Based on the pull - out tests data between geogrids and expansive soil / sands arranged by the orthogonal table l9 ( 34 ), the following conclusions are reached : 1 ) the displacement - properties of pullout tests depend on the pullout speed. the law of factors " affecting degree, which influences the parameters between geogrids and soils in the pulling - out procedure, is obtained. with the concept of " equivalent pull - out displacement ( x ) " brought forward, the whole process of pull out tests is divided into two process - " main process ( when x 1. 0 ) " and " residual process ( when x 1. 0 ) ", and three stages - static friction resistance stage, slip friction resistance stage, and residual friction resistance stage
基於正交設計表l9 （ 3 ~ 4 ）分別安排了影響因素與土工格柵膨脹土或砂土界面相互作用參數的拉拔試驗數據，獲悉： 1 ）拉拔試驗位移特性主要取決于影響因素中拉拔速率；通過分析並獲取影響因素對筋土界面相互作用參數的影響程度及其在拉拔試驗過程中的變化規律，提出了當量拉拔位移（ x ）的概念，並據此將拉拔試驗全過程劃分成「主過程（ x 1 . 0 ） 」和「殘余過程（ x 1 . 0 ） 」 ；且將影響因素對拉拔力或摩擦阻力系數的影響程度分成三階段（靜摩擦阻力階段、滑動摩擦阻力階段，殘余摩擦阻力階段） ； 2 ）不同（規范）定義的筋土界面摩擦阻力系數數值相差較大，但影響因素對摩擦阻力系數影響程度及其變化規律不會因不同（規范）定義而受到影響。This slightly greater force in called static friction
相對運動之前的這種較大的力稱之為靜摩擦。A method is provided to measure the friction parameters of the bed. the maximum friction torque, coulomb friction torque, viscous friction coefficient and moment of inertia can be gotten by fitting the free reduced rate curve of the gimbals and measuring the motor current when the motor begins to rotate
提出了一種測量轉臺摩擦特性的方法，通過對轉臺在無外推力作用下的速度衰減曲線的擬合以及電機啟動過程電流和轉速的測量，可以得到最大靜摩擦力矩、庫侖摩擦力矩、粘滯摩擦系數及轉動慣量。Footwear - test methods for lining and insocks - static friction
鞋靴.鞋襯和鞋內層試驗方法.靜摩擦Hydraulic controlled reciprocating tester applied to measure the static friction
利用液壓控制往復實驗機實現靜摩擦測量Description : static friction torque vs. speed curve during the deceleration phase
描述：馬達在減速階段的靜摩擦扭矩。Footwear - test methods for lining and insocks - static friction ; german version en 12826 : 2000
鞋靴.鞋襯和鞋內層的試驗方法.靜摩擦Angle of friction
靜摩擦角08. 02 test method for static and kinetic coefficients of friction of plastic film and sheeting
塑料薄膜和薄板靜摩擦和動摩擦系數測試方法Rubber or plastic coated fabrics - determination of the static and dynamic coefficient of friction
橡膠或塑料塗層織物.靜摩擦和動摩擦系數的測定The experiment and simulation results show that the stabilization error peak is caused by the step friction torque when the disturbance changes its direction
實驗和模擬顯示轉臺穩定誤差在擾動換向時的「尖峰」由轉臺轉軸的靜摩擦階躍干擾力矩產生。The right undersdanding of sliding friction force and static friction force is stressed by an explaination about a typical topic
摘要通過對一道典型題的解答，強調對滑動摩擦力和靜摩擦力的正確理解。Paper - printing and business paper - determination of the coefficient of static friction
紙張.印刷和商業用紙.靜摩擦系數的測定Paper. printing and business paper. determination of the coefficient of static friction
紙張.印刷用紙和商業用紙.靜摩擦系數的測定Standard test method for static coefficient of friction of polish - coated flooring surfaces as measured by the james machine
用james機測量拋光塗覆地板表面靜摩擦系數的標準試驗方法The result indicate the average value of static friction factor and dynamic friction factor for the central - left side is greater than the central - right side of runway
針對靜摩擦系數或動摩擦系數，就所得結果跑道中心左側區域之平均值大於右側區域平均值。Paper and board. paper, board, corrugated board and their components. determination of the coefficient of static friction and ' estimation of the coefficient of dynamic friction dynamometer method
紙和紙板.紙張紙板和瓦楞紙板及其組成部分.靜摩擦系數測定和動摩擦系數估算測力計法Frictional coefficient of paper / al / pe film was measured on different surface and different direction, and the data was analyzed and compared with these different ingredients, thus the frictional coefficient of this new material could be better understood
摘要通過對紙鋁塑復合薄膜正反兩摩擦基材面相互摩擦及不同角度摩擦的動、靜摩擦系數值的測定，比較並分析了不同摩擦基材面和不同摩擦方向對其大小的影響，從而對這種新材料的摩擦系數有了進一步的認識。The 3d model of mold is analyzed in 3d fem by using ugh. base on the analyses result, some danger structure of the model have been found and some suggestions of the mold modification are given. since doing a lot of research about the 3d cadvcae technology, a 3dcad system of selecting mold for aluminum material have been developed and the method of analyzing the 3d model is provided in this paper
然後，為了能真實地模擬實際生產過程，進行鋁與模具鋼在一定表面粗糙度、不同溫度條件、不同潤滑接觸狀態下的最大靜摩擦系數實驗，總結摩擦系數隨溫度變化的規律性和取值范圍；最後，應用ug 17 . 0三維有限元cae模塊進行模具三維力場分析，根據三維有限元的結果分析，對模具危險部分進行預變形的處理和優化，改善模具受力變形的狀況。分享友人