頂輥 的英文怎麼說
中文拼音 [dǐnggǔn]
頂輥
英文
toroll-
Main product : tungsten carbide powder, roll ring, anvil and cylinder, mining button bit, dies nib for various application : cold heading dies, drawing dies and non - magnetic carbide dies. all of the products mentioned above could be offered in blank or finishing product
公司主要產品有:碳化鎢粉硬質合金輥環頂錘和壓缸冷鐓模無磁合金礦山柱拉絲拉管模棒材板材非標模具及硬質合金精密加工產品等,廣泛應用於鋼鐵標準件金剛石粉末冶金石油礦山磁性材料機械加工電子等行業。3. top air style oven open, initiative guiding roll in oven
3氣頂式烘箱開啟,箱內導輥主動。1. lengthened drying box, pneumatic open, driving guide roller in the box, automatic control for permanent temperature
1加長型烘箱氣頂式開啟箱內導輥主動溫度恆溫自動控制。The dried powder raw materials will be fed from the top of dry granulator, then enters into flaking machine where becomes flakiness raw material will be made into the needed granule product through the procedures of crushing, processing granule and sieving powder and so on
乾燥后的各種乾粉物料從干法制粒機的頂部進入,經預壓進入軋片機內,在軋片機的雙輥擠壓下;物料變成了片狀、片狀物料經過破碎、整粒、篩粉等過程,得到需要的粒狀產品。On the up - roll. . fire
瞄準頂輥…開火!On the up - roll. fire
瞄準頂輥開火!The forward axis and the back axis use a uniformity fluid system. except the motors and the pipelines of the two system, the others parts are consisted of a single mobile power station. this is a one advantage of fluid drive system comparing to mechanical drive system
壓榨機頂輥採用單獨的一套液壓系統,前後輥合用一套液壓系統(主要是共用液壓油箱) ,將上述兩個液壓系統組合成一個可移動的模塊式動力站,這種模塊化的結構也是液壓驅動系統對比機械傳動系統的優勢之一。Products : 50 tons drawing dies, 100 tons punching dies, 150 tons carbide parts for diamond manufacturing, 100tons rollers, 100 tons seal rings and 150 tons other special parts
產品方案:各種線、棒、管材控制模50噸、沖壓模具100噸、頂錘壓缸150噸、軋輥環100噸、密封環100噸、其它異形產品300噸。The speed reducer upper on the main machine makes central axis rotate through shaft coupling, and roller hanger rotates with central axis, and rollers on the hanger roll around the inside of ring
安裝在主機頂部的減速機,通過聯軸器連接中心軸旋轉,中心軸帶動磨輥吊架旋轉,磨輥裝在吊架上沿磨環內周一起滾動。The speed reducer upper installed on the main machine makes central axis rotate through shaft coupling, and roller hanger rotates with central axis, and rollers on the hanger roll around the inside of ring
安裝在主機頂部的減速機,通過聯軸器連接中心軸旋轉,中心軸帶動磨輥吊架旋轉,磨輥裝在吊架上沿磨環內周一起滾動。The results indicate that the time of press influences sawtooth distortion greatly, but infects sawtooth less. root of the sawtooth made by the method of static simulating rolling have no changes hardly, and from the upper distance the changes became, then on the top the sawtooth curves to the opposite direction
結果表明:壓制時間對齒形的變形影響較大,對齒型的影響很小;模擬軋輥壓制的鋸齒,根部一段幾乎沒有變化,是從一段距離開始變形,然後在頂端向相反的方向彎曲;壓製成型后,鋁板厚度的變化很小。分享友人