順序先行控制 的英文怎麼說

中文拼音 [shùnxùxiānhángkòngzhì]
順序先行控制 英文
sequential advanced control
  • 順 : Ⅰ介詞1 （向著同一個方向） in the same direction as; with 2 （依著自然情勢; 沿著） along; in the d...
  • 先 : 名詞1 （時間或次序在前的） earlier; before; first; in advance 2 （祖先; 上代） elder generation; ...
  • 行 : 行Ⅰ名詞1 （行列） line; row 2 （排行） seniority among brothers and sisters:你行幾? 我行三。where...
  • 控 : 動詞1 （告發;控告） accuse; charge 2 （控制） control; dominate 3 （使容器口兒朝下 讓裏面的液體慢...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 順序 : 1. （次序） plain sequence; subsequence; order; sequence; succession2. （順著次序） in proper order; in turn
  • 控制 : control; dominate; regulate; govern; manage; check; cybernate; manipulate; encraty; rule; rein; c...
  1. First of all, this article has been clear several concepts about construction cost, development cost and complete cost. the construction cost constructs by the preliminary engineering cost, the infrastructure expense, the construction and installation engineering cost, the necessary facility spends. the development cost constructs by the land cost, constructs the cost, the development indirect expense. the complete cost constructs by development cost and period expense

    針對這一社會熱點問題，本文以長影世紀村一期工程為例，從成本控制理論入手，敘述了房地產開發成本構成，按照房地產開發進程的先後順序進行展開，較為詳細地論述了項目前期、規劃設計階段、招標采購環節、施工階段、銷售環節、期間費用的成本控制措施。
  2. Fabrication of the box beam is divided into such parts as reinforcement, formwork, concreting, prestressing, moving and storing of beam, pipe grouting under pressure, end sealing of the beam, water - proof layer on the bridge surface system, protective coating etc. the paper makes description of effective box beam construction technology and workmanship which can be adopted in other projects, such technologies as : manufacturing and fixing of reinforcement, steel reinforcement fixing baseplate, web plate and top plate respectively and lifting the steel skeleton into form, requirements of design and manufacturing and way of utilization for dismantling - erection type formwork and hydraulic formwork, optimization of concrete ratio, concrete pouring process of two ends of beam in priority over the middle, in sequence of first baseplate followed by web plate and top plate at last, concrete pouring in inclined section and in horizontal layer, concrete vibration mainly by external vibrator in assistance with internal vibrator, methods and regulation for steam curing of concrete, dual controls over stress and strain to ensure quality of prestressing workmanship, construction method of effective beam moving by heavy - weight special moving facility, some regulations and key notes about construction of grouting under pressure, beam ends sealing, water - proof layer on the bridge surface system, protective coating

    箱梁製造由鋼筋工程、模板工程、混凝土工程、預應力工程、移存梁工程、孔道壓漿工程、梁體封端工程、橋面防水層和保護層工程等施工環節組成。文中介紹的採用胎具製作和綁扎鋼筋，分底腹板和頂板分別綁扎並吊裝鋼筋骨架入模；拆裝式和液壓式兩種模板的設計、製作要求和使用方法；綜合考慮、優化混凝土配合比，混凝土灌注從兩端至中間、先底板、后腹板、再頂板的施工順序和斜向分段、腹板水平分層、附著式振搗為主、插入式搗固為輔的施工工藝，蒸汽養護的方法和規定；應力應變雙控制確保預應力施工質量的施工技術；採用重物移運器有效移梁的施工方法；壓漿、封端、橋面防水層和保護層施工的一些規定和注意事項等都是對箱梁製造行之有效的施工技術和施工方法，並可為以後類似施工作借鑒。
  3. You can then apply precedence constraints to control the execution order of the tasks

    然後可以應用優先約束來控制任務的執行順序。
  4. In chapter 4 we discuss the design of the high speed and high performance vlsi and its imp1ementation, firstly we ana1yze and compare the features and ru1es of al1 kinds of fft algorithm, adopt complex radix 4 butterfly calcu1ation as basic alu, then discuss all kinds of process architectures, the design thoughts, rule, method, technique way, the characteristics of the design are r4 dit algorithm, pingpong ram design method and pipeline structure between stages. we also analyze the limited word length effect and the method to avoid overflow of the fixed points fft process, bring out the expandable platform mode

    第四章主要討論了高速高性能的快速傅立葉變換處理器的設計和實現，首先分析和比較了各種快速傅立葉變換演算法的特性和規律，提出基4蝶算的演算法具有最好的性價比，討論了順序、級聯、并行和陣列的處理結構，闡述了設計高速高性能快速傅立葉變換處理器時的設計原則、設計思路、所採用的技術路線，驗證並測試fft處理器，分析了定點fft處理過程由於有限字長效應所產生的量化誤差的范圍及防溢出控制辦法，提出了可擴展平臺模式。
  5. For example, if when you inserted the new multiline edit control for the address column, you positioned it above the phone field, the default tab order takes you to that edit control before the multiline edit control

    例如，如果為address列插入新的多行編輯控制項時，將其放在phone欄位之上，那麼預設tab順序會讓您先看到該編輯控制項，再看到多行編輯控制項。
  6. The control flow elements define the logical ordering of job progression by applying precedence constraints

    控制流元素通過應用優先約束來定義作業進行的邏輯順序。
分享友人
分享到 Line

分享到臉書