預制材料 的英文怎麼說

中文拼音 [yùzhìcáiliào]
預制材料 英文
vormaterial semi-finished material
  • 預 : Ⅰ副詞（預先; 事先） in advance; beforehand Ⅱ動詞（參與） take part in
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 材 : 名詞1 （木料） timber 2 （泛指可以直接製成成品的東西; 材料） material 3 （供寫作或參考的資料） ma...
  • 料 : 名詞1 （材料; 原料） material; stuff 2 （喂牲口用的穀物） feed; fodder 3 （料器） glassware 4 （...
  • 材料 : 1. （原料） material 2. （資料） data; material 3. （適于做某種事的人才） makings; stuff
  1. The diffusion welding behavior of single - crystalline cu to single - crystalline - aio with a nb film interlayer and the joint microstructure properties were studied by tem, sem / eds analyses and four - point bend testing. the nb film interlayer deposited by electron beam evaporation on the ceramic side prior to diffusion welding was found to be olycrytalline and fiber - textured after diffusion bonding, with the close - packed plane ( 110 ) being parallel to the ( 0001 ) basal plane of - aio

    擴散連接技術是一門邊緣科學，涉及材料、擴散、相變、界面反應、接頭應力應變等各種行為，工藝參數多，雖然已經進行了大量的試驗研究，但卻對各種材料的連接機理尚未有明確的認識，為此人們試圖藉助于計算技術，對接頭行為進行數值模擬，以便找到共同規律，對擴散連接過程及質量進行預測與實時控制。
  2. This article choosed out organic phase change materials, and, the solid - liquid - equilibrium of eleven binary system including fatty alcohol / fatty acid, n - octadecane / fatty acid, n - octadecane / fatty alcohol system were determined by cooling curve, and, t - x phase diagrams of these systems were drawn. the result shows that all these systems are simple eutectic, at the same time, the entropy of phase change of every system in the eutectic point is determined by using differential scanning calorimetry ( dsc ). and n - octadecane / fatty acid systems were calculated theoretically

    本文初選出部分有機相變貯能材料，採用步冷曲線法測定了12醇-羧酸系列、 18烷-羧酸系列、 18烷- 12醇體系共11組體系的二元固液相平衡關系，繪制了這11組體系的t - x相圖，測定結果表明，這幾組體系均為簡單低共熔體系；同時利用差熱掃描量熱法（ dsc ）對上面各組體系低共熔點處的相變焓進行了測定；並對18烷-羧酸系列進行了熱力學理論預測。
  3. Standard test method for tumbling friability of preformed block - type thermal insulation

    預制塊型隔熱材料翻滾時易碎性的標準試驗方法
  4. Thermal insulating materials - magnesia preformed insulation

    隔熱材料.第1部分:預制氧化鎂絕熱材料
  5. The results of performance testing showed that the additive of nano - powders can evidently enhance the latex coatings " weathering resistance, scratch resistance, water resistance and alkaline resistance, and do not reduce other performances ; polybasic nano - composite powders have more efficient than single nano - powder ; the dispersing method have biggish effect on performances. observing the stability of nano - additive of exterior latex coating showed there was no viscidity rising, no delaminatiom sedimentation in two months. tryout by plant showed that nano - weatherability additive can obviously enhance the weathering resistance of latex coating and water resistance, and no reducing other capabilities

    對其性能研究的結果表明，納米粉體材料的引入，可以明顯提高乳膠漆的耐候性、耐洗刷性和耐水耐堿性能，對其它性能無不良影響；納米多元復合粉體比單一粉體的改性效果明顯；納米粉體的添加工藝對改性乳膠漆性能有較大的影響，採用同普通填料一致的添加方式制備的試樣與採用超聲波預分散后在配漆階段加入制備的試樣相比，後者在穩定性、耐候性等方面的性能都有所提高。
  6. Road marking materials. preformed road markings

    路面標記材料.預制的路面標記
  7. Road marking materials - preformed road markings

    道路標記材料.預制道路標記
  8. Wind resistance of prepared roof covering materials

    預制屋面覆蓋材料的抗風阻力
  9. Later, the discovery of all colures photoluminescence and electric - luminescence from porous silicon and the encouraging progress in fabricating porous silicon based light - emitters has cast a new light on si - based opt - electronics

    多孔硅可能彌補單晶硅材料不能有效發光的缺點，預示了用單晶硅制備發光器件進而實現全硅光電子集成的美好前景。
  10. Based on the construction of the testing section for the lining of jiping main canal in shandong province of south - to - north water transfer project, the main causes of the cracking from the mechanized lining concrete slabs are analyzed from the aspects of foundation treatment, bedding layer placement, quality of the raw materials for the concrete, placement of the concrete, cutting of the hardened concrete and the curing of the concrete, and then the relevant prevention and control measures are pertinently put forward

    摘要結合山東省南水北調濟平乾渠工程襯砌試驗段施工情況，著重從地基處理、墊層料鋪設、混凝土原材料質量、混凝土澆築、成型混凝土割縫及養護幾個方面分析了機械化襯砌混凝土板裂縫產生的主要原因，並針對性地提出了預防及控制措施。
  11. The raw materials, the composition, the time of milling, the calcining temperature, the different additives, the sintering temperature and the sintering parameters were investigated. the result showed : it was advantaged to obtain high initial permeability mnzn ferrite with stable frequency characteristic using high - purity raw materials ; in order to obtain mnzn ferrite with high properties, we must control strictly the composition ; it could improve the properties of mnzn ferrite by optimizing calcining temperature. the lower calcining temperature made the permeability higher, and the higher calcining temperature could promote the frequency characteristic of permeability ; we chosen the right time of milling according to the requirement of power diameter ; in order to improve the properties of mnzn ferrite, it is necessary to add effective additives. in this dissertation, the influence of bi2o3 、 moo3 、 k2co3 、 co2o3 were investigated ; the sintering temperature, the time of heat - retaining and sintering parameters were the key factors of preparing high permeability mnzn ferrites

    研究結果表明:採用高純度的fe2o3有利於獲得高起始磁導率且頻率特性優良的鐵氧體;為了制備所需性能的鐵氧體，需要嚴格控制配方中各種原材料的含量，優化配方;由於粉體活性受預燒條件的影響，所以對不同要求的鐵氧體選擇的預燒條件就不一樣，適當降低預燒溫度有利於獲得較高的起始磁導率，而為了獲得良好的頻率特性可以適當地提高預燒溫度;根據對粉體顆粒粒徑的不同需求，可以選擇不同的球磨時間;而有效的添加劑是改善材料性能的必要條件，本文在添加劑的研究中主要對bi2o3 、 moo3 、 k2co3 、 co2o3的影響分別作了詳細地討論;燒結溫度、保溫時間和燒結氣氛是高磁導率mnzn鐵氧體制備最關鍵的工藝，適宜的燒結工藝可以獲得理想微結構和組成，從而得到高性能的鐵氧體材料;而從材料的微結構上來看，要提高材料的截止頻率，就要適當地細化晶粒、增加晶粒內部的氣孔。
  12. It can diagnose quantity limitation ( accident ) of building construction in construction period, and commentate the reasons, measures of prevent and disposal of the quantity limitation ( accident ). the user also can seek information about quality control of building construction in construction period ( quality standards, quality control point, quality control flow, quality of building material and build machinery, laws and regulations and so on )

    它包含了建築工程在施工階段各不同分部和分項工程常見質量缺陷（事故）的診斷、原因分析、預防和處理。用戶還可通過本系統查找建築工程施工階段質量控制的相關資料（如質量控制標準、質量控制點、質量控制流程、工程材料質量控制、施工機械質量控制及有關法規等） 。
  13. Standard specification for preformed flexible elastomeric cellular thermal insulation in sheet and tubular form

    片式和管式預制柔性彈性體蜂窩狀絕熱材料的標準規范
  14. Preform technology of carbon - carbon composites nozzle exit cone

    炭材料出口錐預制體技術
  15. Aerospace series. titanium and titanium alloy remelting stock and castings. technical specification. part 3 : pre - production and production castings

    航空航天.鈦和鈦合金制預制材料和鑄件.交貨技術條件.第3部分:試制鑄件和系列鑄件
  16. Then construct relation between crystal structure, interface structure and mechanical, magnetic properties of composites and predict and control the properties of material from the interface structure varying, on the basis of that developing the principle of design of interface structure

    從界面結構變化的角度來預測和控制材料的性能，在此基礎上發展陶瓷材料的界面結構設計理論，並為最終研製出高性能的結構陶瓷-硬磁鐵氧體結構-功能一體化復合材料打下基礎。
  17. Cold applied preformed material

    冷鋪預制材料
  18. Aerospace series. titanium and titanium alloy remelting stock and castings. technical specification. part 2 : remelting stock

    航空航天.鈦和鈦合金預制材料和鑄件.交貨技術條件.第2部分:預制材料
  19. Refractory products. prepared unshaped materials. dense and insulating hydraulic cements. determination of classification characteristics

    耐火製品.非異型預制材料.密實的水硬水泥.分級特性的測定
  20. Aerospace series. titanium and titanium alloy remelting stock and castings. technical specification. part 1 : general requirements

    航空航天.鈦和鈦合金預制材料和鑄件.交貨技術條件.第1部分:一般要求
分享友人
分享到 Line

分享到臉書