驅動小齒輪 的英文怎麼說
中文拼音 [qūdòngxiǎochǐlún]
驅動小齒輪
英文
drive pinion- 驅 : 動詞1. (趕) drive (a horse, car, etc. ) 2. (快跑) run quickly 3. (趕走) expel; disperse
- 小 : Ⅰ形容詞1 (體積、面積、數量、強度等不大) small; little; petty; minor 2 (年紀小的; 年幼的) youn...
- 齒 : Ⅰ名詞1 (牙; 牙齒) tooth 2 (物體上齒形的部分) a tooth like part of anything 3 [書面語] (年齡...
- 輪 : Ⅰ名1 (輪子) wheel 2 (像輪子的東西) wheel like object; ring; disc 3 (輪船) steamer; steamboa...
- 驅動 : [機械工程] drive; prime mover
- 齒輪 : gear [rack; toothed] wheel; (toothed) gear; wheel gear
-
The discharge material flows across the discharge trunnion liner to exit the mill
可旋轉的小齒輪與裝配了大齒輪的筒體法蘭相蹌合,驅動筒體旋轉。Check the gear wheel drive in the groove of the wall, select four gear wheel ( red pinion is not used ) of different size for use, load heavy gear wheel, times of heavy gear wheel, times of light gear wheel, minimum gear wheel most onto separately from left to right, make gear wheel hand in, form each other, leave behind, operate a switch, drive, finish
檢查墻壁凹槽中的齒輪驅動裝置,選用大小不同的四個齒輪(紅色的小齒輪不用) ,從左到右分別裝上最大的齒輪、次大的齒輪、次小的齒輪、最小的齒輪,並使齒輪間相互交結,拉下拉閘,驅動完成。The changing carbon potential carburization - hot oil matrempering technology of helical bevel gear for automobile driven axle is introduced in this article. the board test and production application show that the technology not only quenchs directly gear after carbrization, but also decreases the heat treatment deformation and raises the contact fatigue life of gear
介紹了汽車驅動橋螺旋錐齒輪的變碳勢滲碳一熱油分級淬火工藝,臺架試驗及生產應用表明,該工藝與專用滲碳淬火掛具相結合,不僅可實現齒輪滲碳后直接淬火,而且熱處理變形小,齒輪接觸疲勞壽命也有所提高。The minimum centre distance is sometimes governed by the amount of chain lap on the driver sprocket, our normal recommendation in this circumstance being not less than six teeth in engagement with the chain
最小中心距有時由驅動鏈輪輪齒與鏈條接觸數量決定,在這種情況下我們通常建議有不少於6個的輪齒與鏈條嚙合。This is achieved by utilising a torque transfer differential which is controlled by various sensors and an electronic control unit ( ecu ) to enable a difference in torque to go to each of the rear wheels
感應器根據收集到的轉向角度,油門大小,車輪轉速,前後,側向加速力等信息經過計算后,電腦控制油壓系統介入,推動差速器里的離合裝置,把驅動力誘導到一組減速齒輪,從而改變左右輪驅動力。This paper gives the way of using the ac servo drive instead of the traditional drive mode consisted of the main motor, the gears and belts, realizing the synchronous drives of the multi - motors. the closed loop control technology of the speed and the position embedding has been adopted to track in real time, then to reduce the transmission error and the noise, so as to increase the control precision and the stability of the combination and simplify the maintenance and repair of the mechanical and technical system
採用交流伺服驅動代替傳統的由主電機、齒輪和皮帶組成的傳動方式,實現多電機同步驅動;採用速度環和位置環嵌套的閉環控制技術,進行實時跟蹤,達到減小傳動誤差、減小噪音,增強機組的控制精度與穩定性、簡化機電系統的維護與修理的效果。An over - running clutch on the drive pinion prevents the starter from being driven by the engine once it starts
在驅動小齒輪上的一個超轉離合器可避免啟動馬達被引擎帶動,一旦引擎啟動了。分享友人