驅動缸 的英文怎麼說

中文拼音 [qūdònggāng]
驅動缸 英文
actuating cylinder
  • 驅 : 動詞1. （趕） drive （a horse, car, etc. ） 2. （快跑） run quickly 3. （趕走） expel; disperse
  • 缸 : 名詞1. （盛東西的器物） jar; jug; vat; crock 2. （缸瓦） earthenware with crude glaze 3. （像缸的器物） jar-like things
  • 驅動 : [機械工程] drive; prime mover
  1. The machine is circumgyration drilling machine that the rotary drives drilling tool to bore by rotation, adopts full hydraulic pressure drive, constant power loop, wheel cylinder startup, oil cylinder disappear ing end bumper, electrohydraulic combined control, steel wheel traveling and disassembly transport

    該機是由轉盤帶動鉆具旋轉鉆進的回轉鉆機，採用全液壓驅動，恆功率迴路，分泵啟動，油缸升降，電液復合操縱，鋼輪行走，解體運輸。
  2. Cylinder actuators can be provided with manual overrides for emergency valve actuation, fail safe mode and other accessories

    缸體執行機構可以配置針對緊急狀態下的手動過載裝置，閥門驅動，故障安全功能和其它附件。
  3. Due to the electrohydraulic servo mechanism was used to drive the motion deck of the semi - physical simulator on the ground. therefore, the model of electrodraulic servo mechanism was built based on the fundamental equations of hydraulic jar and servo valve

    由於空間對接機構地面半物理模擬系統採用電液伺服驅動機構，因此本文根據電液伺服驅動機構的基本方程，建立單缸電液伺服驅動機構的模型。
  4. The feedbacks of position, velocity, acceleration and dynamic pressure were applied to adjust the model, so the control system of single jar electrodraulic servo mechanism was built. to reduce the system error and interference error, the compound control was designed. the results of simulations showed that the magnitude attenuation and phase lag of the system come to the project demand

    引入包括位置反饋、速度反饋、加速度反饋和動壓反饋在內的反饋控制技術對電液伺服驅動機構模型進行綜合校正，從而建立單缸電液伺服控制系統，並在分析系統誤差和擾動誤差后，加入復合控制減小系統誤差和抑制干擾，模擬結果表明復合控制系統的控製品質有了明顯改善，能夠滿足工程需求。
  5. Kinematics and kinetics analysis of hydraulic cylinder powered scissors mechanism

    液壓缸驅動的剪刀撐機構運動及動力學分析
  6. Owing to the advantages of air - pressure transmission, the dividing mechanism driven by the reciprocal linear movement of pneumatic cylinder has been applied broader and broader the one - way dividing mechanism of butterfly - hoard oscillation was one of the mechanisms among them

    摘要由於氣壓傳動的優點，由氣缸往復直線移動驅動的分度機構應用越來越廣，蝶板擺動單向分度機構就是其中之一。
  7. The formula and analysis would be helpful for the theoretical analysis and engineering design of the hydraulic cylinder piston ring seal structure

    研究結果為控制棒水壓驅動機構水壓缸活塞環密封結構的設計和分析提供了理論基礎。
  8. By analyzing the results of the crhdm single cylinder experiment, constants in the formula of the flow resistance were obtained

    利用控制棒水壓驅動機構單缸性能實驗的結果，擬合求得了流阻公式中的系數，並將公式計算流阻與實驗結果進行了對比。
  9. According to the control rod hydraulic drive mechanism ( crhdm ) and the characteristics of its hydraulic cylinder seal structure, the leaking ways of the hydraulic cylinder piston ring seal were analysed, its theoretical calculation model was built and its flow resistance formula based on the calculation model of differential pressure at the hydraulic cylinder piston ring seal was deduced

    摘要根據控制棒水壓驅動機構水壓缸活塞環密封結構的特點，分析了水壓缸活塞環的泄漏途徑，建立了活塞環密封泄漏流阻的理論計算模型，並結合水壓缸活塞環密封處的壓差計算模型，推導出水壓缸密封結構的流阻計算公式。
  10. Overturn and transfer mechanism driven by cylinder

    基於汽缸驅動的翻轉移動機構
  11. The design undertaken mainly from the following aspects : 1, mechanism ddesign : included the base and the joints : 2, trasmission mechanism design : adopted a synchronous toothelike transmission bell ; 3, balance system design : adopted springs and a brake and a lay air cylinder ; 4, design parameter and verify alculation ; 5, established motion equation by d - h method ; 6, simulated the motion locus by matlab software ; 7 ^ mapping out the part drawing or asesembly drawing

    本設計主要是從以下幾個方面入手： 1 、機構設計：包括底座和臂關節的設計； 2 、傳動機構設計：將驅動電機安裝在底座上，利用同步齒型帶、離合器傳遞手臂的動力；利用齒輪傳動帶動底座回轉； 3 、平衡系統設計：採用了彈簧平衡系統、電磁式制動器和單向延時氣缸； 4 、設計參數和校核計算； 5 、用d ? h法建立運動學方程； 6 、利用matlab軟體對手臂的運動空間進行模擬； 7 、利用autocad2000繪圖：包括零件圖和裝配圖。
  12. The engineering drilling machine of kp2200 type is double layers bottom plate, and drives through hydraulic pressure, upper plate can move fore and aft on the lower plate, the drill power leans back under the action of oil cylinder, the lower plate can put the drilling tool within 2. 5 meters into well hole without moving, it is convenient and reliable, and ensures construction quality

    Kp2200型工程鉆機為雙層底盤，通過液壓驅動，上盤可在下盤上前後移動，鉆塔在油缸的作用下後仰，下盤不動即可把2 . 2米以內的鉆具放入井孔內，方便可靠，保證施工質量。
  13. The three dimensional flow field of the step cylinder in hydraulic control rod driving system ( hcrds ) is calculated and analyzed with the computational fluid dynamics program cfx5 in detail

    摘要應用計算流體力學程序cfx5對水力驅動控制棒步進缸內部的三維流場進行了計算和分析。
  14. A new sliding vane compressor with a pinned rotary cylinder driving the rolling piston is presented in this paper. this paper analyzes the structure characters and the structure parameters of the new sliding vane compressor with a pinned rotary cylinder driving the rolling piston by means of contrasting with other compressors. a means that designs the suction and exhaust in the new sliding vane compressor with solid works and excel is brought forward

    本文介紹了一種新型結構的滑片壓縮機? ?轉缸驅動轉子滑片壓縮機，通過與其它型式壓縮機在結構及工作過程上的對比，詳細分析了這種壓縮機的結構特點和結構參數，並提出了一種結合三維軟體solidworks和電子表格excel設計吸排氣口的新方法。
  15. Furthermore, it discusses how to figure out these models mentioned above. with reference to the design of various automobiles, it primary defines the method to get key parameters in platform lorry general design, and creates mathematical model. it provides more reference to choose axis, driving axle, number of arrest axles, type of tire, pump, motor, lift hydrocylinder, maximum payload and sole weight reasonably

    在參考各類汽車設計思想的基礎上，根據理論推導和經驗公式的計算，初步確定了平板車總體設計階段的主要技術參數的求解方法，建立了數學模型，為合理地選擇軸、驅動橋、制動橋個數，輪胎型號、泵、馬達、舉升油缸、平板車的最大載重量和自重的選擇等提供了依據。
  16. They have used the bicycle pump and the motor for the performance setup. the control system of the fiber winding / fiber placement is usual to adapt computer numerical control

    它們使用電機和氣缸作為驅動執行元件。纖維纏繞纖維鋪放成型技術的控制系統主要是採用計算機數控技術來實現。
  17. An insulating lift is presented to improve the insulation property between the gripper and ground of high voltage hot - line cleaning robot, and to decrease the initial cylinder ' s working - pressure of vertical lifting mechanism

    摘要提出了一種絕緣升降平臺，用於提高高壓帶電清掃機器人帶電作業時的對地絕緣性能，同時降低機器人垂直升降機構驅動油缸的初始工作壓力。
  18. Dynamics analysis studies the force of the actuator by the newton - euler approach, the force was created by motion parameter

    動力學運用牛頓-歐拉法進行分析，由運動平臺的運動參數得出各個液壓缸的驅動力。
  19. Volvo s80 shoppers can choose between a new 3. 2 - liter inline six - cylinder engine with front - wheel drive and a 4. 4 - liter v8 engine with all - wheel drive

    沃爾沃s80的購買者可以選擇兩款發動機：一款是前輪驅動直列3 . 2升六缸發動機，一款是全輪驅動4 . 4升v8發動機。
  20. It is battery - driven and can be recharged from the mains or by an on - board three - cylinder engine that never directly drives the wheels

    它由電池驅動，可用家用插座充電，也可由車載三缸渦輪引擎進行充電- - - -這個引擎是不能直接用來發動車子的。
分享友人
分享到 Line

分享到臉書