高壓噴霧 的英文怎麼說
中文拼音 [gāoyāpēnwù]
高壓噴霧
英文
high-pressure fog-
More than 50 % of cane land is irrigated, mainly by sprays or flooding of furrows. use of low - pressure overhead irrigators and drip systems is increasing
採用噴霧灌溉或渠灌的甘蔗地超過50 % ,使用低壓高架灌溉器和滴水灌溉系統的正在增加。This " paper mainly researches on the humidifying property of the centrifugal nozzle with firing pin type, high pressure and little aperture
課題主要對撞針型高壓小孔徑離心式噴嘴的霧化加濕性能進行研究。As to the work about theory analysis, at first, the paper describes the atomizing and humidifying process of the centrifugal nozzle with firing pin type, high pressure and little aperture and liquid physical properties. later, combining with the structure characters of this kind of nozzle, the paper studies on the theory of the atomizing and humidifying process by three phases, which is water film forming phase, water film falling into pieces phase, and heat and mass transfer between water and air phase in turn
理論工作方面,首先描述了撞針型高壓小孔徑離心式噴嘴的霧化加濕過程和液體的物理性質,然後結合撞針型高壓小孔徑離心式噴嘴的結構特點,將其霧化加濕過程分三個階段進行機理上的研究,這三個階段依次為液膜形成、液膜初次破碎及二次霧化、水與空氣的熱濕交換。Based on the theory analysis and experiment work, the paper studies the humidifying property of the centrifugal nozzle with firing pin type, high pressure and little aperture. compared with the traditional air washer, the high efficiency and energy saving character of this kind of nozzle is stood out
課題從理論和試驗兩方面分析研究了撞針型高壓小孔徑離心式噴嘴的霧化加濕性能,並將其與傳統噴水室加濕系統進行能耗比較,突出了撞針型高壓小孔徑離心式噴嘴高效節能的特點。Through the special studies on impacts to atomizing and humidifying effect from such factors as the firing pin type, centrifugal structure, higher spraying pressure, less aperture, initial water temperature and original state of the air, some conclusions are obtained, such as : the centrifugal nozzle with firing pin type, high pressure and little aperture has bigger air eddy and atomizing angle. the spaying liquid has high velocity. the droplet is small, and the heat and mass transfer velocity is high
通過對撞針型結構、離心式結構、較高的噴水壓力、較小的噴嘴孔徑、噴水初溫及待加濕空氣初狀態對霧化加濕效果的作用原理的重點分析,得到:撞針型高壓小孔徑離心式噴嘴具有較大的空氣渦與霧化角,噴出的液體流速高、液滴小、水與空氣傳熱傳質速率高,撞針型結構提高了霧化加濕效率,高壓小孔徑的特點為霧化加濕提供了較大的能量,而噴水初溫的升高會減小水的粘性力和表面張力,從而優化加濕效果。Integrated the work on theory and experiment, the paper provides technical performance material at large about the automating and humidifying character of the centrifugal nozzle with firing pin type, high pressure and little aperture to the manufacture and user. with the valuable reference during the selecting the equipment and ascertaining the parameters, the users could select and control the humid parameter
課題的理論與試驗兩方面工作相結合,為撞針型高壓小孔徑離心式噴嘴的霧化加濕性能提供了較為詳細的技術性能資料,為生產廠家和用戶在設備選型和參數選擇過程中,提供了有價值的參考,便於用戶正確而經濟地選擇、控制濕度參數,有效調節噴嘴孔徑、噴水初溫和噴水壓力的大小。By analyzing and predicting the microclimate in greenhouse in typical weathers, the conclusions are that high temperature with low humidity weather and high temperature with high humidity appear one after the other. the measures are proposed as the followings : to the former, it should be taken to decrease the temperature with soppy shade - fan or spray inside or outside ; to the latter, it should be taken to enlarge the ventilation area, to fit spray apparatus at the top of roof outside, to adopt havelock outside instead inside, to coat the roof white, etc
通過對典型天氣下溫室小氣候變化規律分析和預測,其結論是:從7月中旬到8月中下旬,室內相繼出現高溫低溫和高溫高濕天氣,建議分別採取的適宜措施是:濕簾-風機降溫、高壓噴霧降溫、屋頂噴淋降溫和增大屋頂通風窗的通風面積、安裝屋頂噴淋(霧)設備、改溫室內遮陽為外遮陽、塗白溫室屋頂等。Especially preparation of special high - pressured sparge grain - - hua xinsu, it is to make more long the apparent curative effect that the bitter patient that bridle heart declines achieves contemporary and scientific preparation, businesslike can amount to 92 %, can grow take long with, without the poisonous side - effect of digoxin
尤其是非凡的高壓噴霧顆粒制劑? ?華心素,更是使久羈心衰之苦的患者獲得現代科學制劑的明顯療效,有效率可達92 % ,並可長服久用,沒有地高辛的毒副作用。Very - high - pressure spray nozzle
極高壓噴霧水槍According to the experimental data of droplet size 、 particle spectrum range 、 droplet cone shape 、 flow rate 、 cover area and cover area rate which obtained through changing the pressure of power sprayer and the nozzle diameter in greenhouse , this paper made comparative analysis on atomizing performance in same pressure and different nozzle type between same nozzle type and different pressure. the conclusion is that : the ejection rate and the droplet cone shape change with the variation of pressure and nozzle diameter , average particle diameter decreases obviously and particle quantity increases obviously with the increase of pressure and decrease of nozzle diameter. these results will lay experimental foundation for precise spraying 、 low pollution and highly effective operation
本文根據溫室內動力噴霧機壓力與噴嘴孔徑的變化影響霧滴大小、粒譜范圍、霧錐形狀、流量、覆蓋面積及覆蓋面積率的試驗數據,對相同壓力下不同噴嘴型號和相同噴嘴型號時壓力不同時的微粒化性能進行對比分析和研究,得到如下結論噴出量與霧錐形狀隨著壓力和噴嘴孔徑大小變化而變化;平均粒徑隨著壓力的增加和噴嘴孔徑的減小而明顯減小;粒數隨著壓力的增加和噴嘴孔徑的減小而明顯增多,為精噴量、低污染、高防效的防除作業奠定了實驗基礎。A vacuum interface used for atmospheric pressure ionization ion source was designed to couple with an orthogonal - injection electrospray ionization time - of - flight mass spectrometer ( tofms )
摘要研製了一種大氣壓離子源真空介面,並已將其用於自製高解析度垂直引入式電噴霧電離飛行時間質譜儀。The key items influent on the characteristics of spraying have been also studied in the dissertation, we can get a good spraying result by adjusting the related parameters efficiently. ( 3 ) the theoretical model of the dynamical parameters such as temperature, moisture, pressure and contour for hot medium and particle inside the drying chamber were obtained by model, utilized the computational fluid dynamics technique to solve the problem between spraying droplets medium by arranging the double grid dispersing structure and rotary outlet structure and the developed structure improved the drying efficiency and product quality
( 3 )採用-模型實現了壓力噴霧乾燥塔的溫度場、濕度場、流場的理論建模,利用計算流體力學( cfd )技術來解決噴霧乾燥過程中熱介質與霧滴間的傳熱傳質以及動量傳遞和湍流擾動等問題,避免了乾燥過程中的設計不合理狀況;通過增加雙格柵均風裝置和旋轉出風裝置,改善了乾燥塔內的熱質傳遞,提高了乾燥塔的體積蒸發強度。The pump is equipment with extensive uses, which can homogenize and fine material liquids or make the material liquids to form highpressured spray
本泵是一種用途廣泛的能將料液均質細化,或使料液形成高壓噴霧的設備。Its atomized parcel is so small that no drip is separated out. this kind of centrifugal nozzle has high humidifying efficiency and low energy cost, which could be used in many situations in textile factories such as directly humidifying in workshop and humidifying in air pipeline
撞針型高壓小孔徑離心式噴嘴的霧化粒子細小、無水滴析出、加濕效率高、耗能少,可直接向車間加濕,適用於紡織廠等多種應用場合。As to the work about experiment study, at first, the paper makes certain the prominent affecting factors to the automating and humidifying property of this kind of nozzle by orthogonal experiment. by jicha analysis method and fangcha analysis method, the paper got that the nozzle aperture, the initial water temperature and the spraying pressure have prominent effect to the humidifying property while the effect of the original air state is small
試驗工作方面,首先通過正交試驗確定對撞針型高壓小孔徑離心式噴嘴霧化加濕性能影響顯著的因素,運用極差分析法和方差分析法,得到噴嘴孔徑、噴水初溫和噴水壓力對噴嘴的加濕性能影響顯著,而待加濕空氣初狀態的影響相對較小。The works would include creation of negative pressure gradient in wards, provision of 100 per cent fresh air supply and dilution of bioload in sufficient air change rates, installation of high efficiency particulate air filters to filter out droplets and aerosols, and the provision of en - suite toiletshower facilities in ward cubicles where building structure and existing building services installations permit
工程將包括在病房內製造負氣壓坡度;以足夠的換氣率,供應百分之百的新鮮空氣以及稀釋空氣中的微生物含量;安裝高效能空氣粒子過濾器,過濾飛沫和噴霧;以及在建築結構和現有屋宇裝備許可的情況下,在病房單間內提供獨立洗手間和淋浴設施。The cold fog is produced by a special device ( cold fogger ) that breaks up the chemical into microscopic droplets by mechanical means, basically with a high - pressure pump and an extreme fine nozzle
(冷噴霧器)製造。基本來說,此裝置用高壓泵和極細的噴嘴,以機械方法把化學液體變成微細的霧滴。Use the high pressure sprayer, do not spray on electrical equipments. spray to roof and wall
噴霧可用高壓噴槍,注意噴霧要均勻,房頂和墻壁都要噴到,不要噴至配電盒等電器設備。Hence, careful validation of the individual breakup models serves as an important prerequiste for the successful analysis and the optimization of high pressure sprays in diesel as well as in gasoline engines
每個模型的仔細確認成為成功分析和優化柴油機和汽油機高壓噴霧的主要條件之一。High speed photography is applied to take pictures of high pressure injection fuel spray, a new formula for calculating the spray development under the high injection pressure is developed
摘要利用高速閃光攝影技術,對高壓噴射噴霧體空間發展規律進行了試驗分析,提出了一個新的計算高壓噴射噴霧體發展的數學公式。分享友人