高峰負載 的英文怎麼說

中文拼音 [gāofēngfùzǎi]
高峰負載 英文
peak load
  • 高 : Ⅰ形容詞1 （從下向上距離大; 離地面遠） tall; high 2 （在一般標準或平均程度之上; 等級在上的） above...
  • 峰 : Ⅰ名詞1. （山的突出的尖頂） peak; summit 2. （形狀像山峰的事物） peak-like thing Ⅱ量詞（用於駱駝）
  • 負 : Ⅰ名詞1 （負擔） burden; load 2 （虧損） loss 3 （失敗） defeat Ⅱ動詞1 [書面語] （背） carry on th...
  • 載 : 載Ⅰ名詞（年） year : 一年半載 six to twelve months; six months to a year; 三年五載 three to five ...
  • 高峰 : peak; summit; climax; height; tor
  • 負載 : [電學] load
  1. Finally, with caparisons of that three parapets properties cantilevered parapets has been adopt to the steel structure of light - weight buildings with gabled frames, numerical simulations have been carried out with that buildings, results of simulations show that device can also significantly reduce the area - averaged coefficient of wind pressure and high negative suction peaks on zones susceptible to wind pressure. formula has been proposed about the height of that parapet

    最後通過三種女兒墻的性能比較確定對門式剛架設置懸挑女兒墻進行數值模擬，結果同樣表明懸挑女兒墻能明顯地降低門式剛架屋面風荷載敏感區的負壓峰值及屋面風荷載體型系數，並給出了女兒墻高度限值公式。
  2. Green - mode which provides off - time modulation to linearly decrease the working frequency under light - load conditions and power limiting which will turn off the transistor when peak current of inductor reaches the threshold current

    同時該電路集成了能在輕負載情況下自動降低頻率的綠色模式以及能在電感峰值電流過高時關斷調整管的功率限制模塊，降低了系統的功耗。
  3. As the ratio of peak samples to total training samples is low, the prediction accuracy of peak load is poor when applying support vector machine ( svm ) model to predict a periodical load

    在應用svm模型于具有周期性負荷的預測時，由於在訓練樣本中峰值或谷值樣本所佔比例很少，從而導致峰值荷載預測精度不高。
  4. At first, the development and fundamental of monolithic switching power supply are presented in this thesis. then a novel monolithic switching power supply circuit only with four terminals is analyzed at detail. it uses pulse skip modulation and current - mode topology

    論文研究了一種作為psoc原型電路的四端單片開關電源電路，此電路採用新型的跨周期調制模式，與傳統的脈寬調制模式相比，提高了輕負載下的工作效率;整體控制迴路採用電流峰值控制模式。
  5. Different distribution of power loss can be worked out by mathcad software based on the formula reasoning. the result of calculation is consistent with that of the experiment, which proves that this method is right. it is pointed out through the analysis of calculating data that the key to improve efficiency at the same output power is to decrease the peak current and rms current of power switches or the on - resistance of mosfet and windings

    由推導可得損耗計算公式，利用數學計算軟體計算出電路輸出從空載到410w阻性負載時損耗分佈變化，該結果與實驗數據基本相吻合，證實了這種方法的正確性；通過對計算數據的分析，指出了進一步提高效率的關鍵在於輸出相同功率時降低功率管的電流峰值和有效值，減小繞組和mosfet的導通電阻。
分享友人
分享到 Line

分享到臉書