高度調整閥 的英文怎麼說
中文拼音 [gāodùdiàozhěngfá]
高度調整閥
英文
leveling valve- 高 : Ⅰ形容詞1 (從下向上距離大; 離地面遠) tall; high 2 (在一般標準或平均程度之上; 等級在上的) above...
- 度 : 度動詞[書面語] (推測; 估計) surmise; estimate
- 調 : Ⅰ動詞1 (配合得均勻合適) harmonize; suit well; fit in perfectly 2 (使配合得均勻合適) mix; adju...
- 整 : Ⅰ形容詞1 (全部在內; 完整) whole; all; complete 2 (整齊) neat; tidy; orderly Ⅱ動詞1 (整理; 整...
- 閥 : 名詞1 (指在某方面有支配勢力的人物或家族) established house or power group; a powerful person or...
- 高度 : altitudeheightelevation
- 調整 : adjust; tune up; trim; trimming; variation; modulation; arrangement; debug; rectification; redres...
-
When the temperature to gas pipelines, temperature packets of material expansion, the pressure rise, inflation pressures are rising corrugated box, corrugated promote the expansion thrust to overcome the spring - loaded pole resistance, the ball - type valve opened for big change ; when the gas pipeline to reduce the temperature, temperature of the material swelling up, the pressure lowered inflation corrugated box pressure also reduced, spring - loaded pole compressed corrugated of resistance to thrust, spherical valves open for smaller ; this constant push and pull adjustment for the balance, as long as refrigeration cycle continue
當回氣管道溫度升高,感溫包內的物質膨脹,壓力升高,膨脹波紋箱內壓力也升高,波紋腔膨脹推動推力桿克服彈簧阻力,球型閥開度變大;當回氣管道溫度減低,感溫包內的物質膨脹,壓力降低,膨脹波紋箱內壓力也降低,彈簧阻力推動推力桿壓縮波紋腔,球型閥開度變小;如此不斷的進行推拉調整平衡,只要製冷循環繼續下去。Because expansion valves are high precision processing components, factory in its internal adjustment of the body parts are processed in a state of complete thermostatic, the temperature of the gas filling kits are demanding more consistent not detect leaks, in the completion of the expansion valve assembly also undergo strict testing and fatigue resistance aging sampling, the construction expansion valves : 1 : indeed temperature temperature kits ; 2 : temperature gas or liquid filled with the expansion corrugated ; 3 : spherical valve seat ; 4 spherical valves ; 5 : spring ; 6 : overheating degrees adjustment screw spacer and screw ; 7 : internal and external ( h - type ) sealed pieces ; 8 : thrust poles and corrugated of spacer ; 9 : fati ; 10 : capillary, and so on
因為膨脹閥是屬于超高精密加工的零件,在工廠對其內部調整機構零件的加工都在恆溫狀態下完成,其中的感溫包的氣體充填更是要求嚴格一致不允許一絲泄漏,在完成裝配的膨脹閥還要經過嚴格的測試和耐疲勞老化抽檢,膨脹閥的構造: 1 :感知溫度的感溫包; 2 :感溫氣體或者液體充填膨脹波紋腔; 3 :球型閥座; 4球型閥; 5 :彈簧; 6 :過熱度調整螺絲墊片和螺絲; 7 :內部和外部( h型)密封件; 8 :推力桿和波紋腔墊片; 9 :閥體; 10 :毛細管等等。The construction of conical nozzle is used by pump ' s delivery - valve, making use of the dynamic characteristics of conventional. short pipe to enhance injection pressure. there are three parameters of fuel injection system : response pressure, injection - advanced angle, injection valve bulge high degree, the best match was found by adjusting them
在油泵出油閥端,採取漸縮管結構措施,利用管路動態效應提高噴油壓力;對于噴油系統參數:噴油壓力、靜態供油提前角和油嘴凸出高度,三個參數進行調整試驗,找到它們的最佳匹配。
分享友人