高效連鑄 的英文怎麼說

中文拼音 [gāoxiàoliánzhù]
高效連鑄 英文
high-efficiency continuous casting
  • 高 : Ⅰ形容詞1 （從下向上距離大; 離地面遠） tall; high 2 （在一般標準或平均程度之上; 等級在上的） above...
  • 效 : Ⅰ名詞（效果; 功用） effect; efficiency; result Ⅱ動詞1 （仿效） imitate; follow the example of 2 ...
  • 連 : Ⅰ動詞1 （連接） link; join; connect 2 （連累） involve （in trouble）; implicate 3 [方言] （縫） ...
  • 鑄 : Ⅰ動詞（鑄造） cast; coin; make Ⅱ名詞1. （古國名） zhu, a state in the zhou dynasty2. （姓氏） a surname
  • 高效 : eff1
  • 連鑄 : cc dr process
  1. The control system of mould level is crucial to improve the slab quality in the continuous casting process, pid controller is used in the traditional mould level control, and it has some defaults, such as : at the start - up or finishing period of casting or during the changeover of tundish, pid control has a bad effect, its overshoot is large and its transient time is long ; the erosion of the tundish stopper and the submersed nozzles lead to the accuracy of control become bad ; the abrupt falloff of block in the submersed nozzles makes the level acutely fluctuate, and pid control can not overcome the disturbances resulted from the change of casting speed

    結晶器液位控制系統是提高連鑄產品質量的關鍵環節，傳統的連鑄機液位控制方法採用常規的pid控制，存在如下不足：開始、結束澆注和換中間罐澆注時，控制效果差，超調量大，過渡時間長；塞棒頭和浸入式水口被腐蝕后引起控制精度差；浸入式水口堵塞物的突然脫落所引起的液位劇烈波動；無法克服拉速波動引起的擾動。
  2. Abstract : based on the research of ladle flow field, the steel flow i ng low of six strands small billet cc ladle is researched, the methods improves s teel flowi ng in the ladle by setting separating and blocking slag wall, separates the steel from the slag, increases the bluyance rate of inclusion, achieves the desired results, and applies itself to the practice

    文摘:在中間包流場分佈分析的基礎上，藉助水模擬試驗研究了6流小方坯連鑄中間包內鋼水流動規律，通過設置分流擋渣墻改進中間包內的鋼水流動，分離鋼水和爐渣，提高鋼中夾雜物的上浮率，達到了預期的效果，並應用於生產實踐
  3. A new type of joint technique between short _ net copper pipe and soft _ cable connection board, castfusion welding, is introduced. the practice of more than ten years shows that this fusion welding connection has the superiority of higher reliability, simpler processing method, better economy benefit compared to the taper cone face - contacted connection

    介紹了電石爐短網銅管與軟纜接線板之間的一種新型連接技術? ?澆鑄熔焊技術.經過10多年的運行，實踐證明短網銅管與鑄銅軟纜接線板的澆鑄熔焊連接，與傳統工藝採用的圓錐面接觸連接相比較，具有加工工藝簡單、運行可靠性高、經濟效益好等優點
  4. Porous coating graphite mould of round and special profile ( for horizontal continuous casting of medium - size and small profiled materials, incrdase work efficiency )

    多孔圓形、異形塗層石墨模具，用於中、小型的型材水平連續鑄造，可有效提高工效。
  5. Oscillator mechanism with four - eccentric axes is widely used in modem continuous casting machine. with the increase of operation speeds of the machine, elastic vibrations of the machine parts became much obviously. in order to design the machine reasonably, the complex dynamic property of the system must be studied deeply

    結晶器四偏心式振動機構是大型連鑄機上廣泛採用的一種振動裝置，隨著拉速的提高，其彈性振動效應非常明顯，對其復雜彈性動力學性能進行深入研究是合理設計該系統的基礎。
  6. In order to adjust structure of production 、 meet requirement of market and improve economic benefit 、 cancel old mould casting system ， pangang decided to enlarge continuous casting ratio and eliminate mould casting system ， pangang decided to install one new bloom casting machine 、 one new 130t lf plants 、 one new 130t rh degassing plants 。 this rh can treat 1000000t molten steel in every year ， it meet mostly request of the rail mill that they produce high quality and high speed heavy rail 。 the writer is a stuff member of this project

    攀鋼公司為了改善產品結構、增強市場竟爭能力和提高經濟效益，淘汰落後模鑄系統，決定擴大連鑄比並淘汰模鑄，新建一臺六流方坯連鑄機、一臺rh真空處理精煉裝置、一座lf爐。這臺新建rh真空處理裝置年處理鋼水100萬噸，主要滿足軌梁廠生產優質高速重軌和型鋼的要求。作者作為該項目的三電部分主要參與人。
  7. Abstract : this article presents the problems and the reasons causing the problems in the operation of slab ccm mold in pansteel. a study has been carried out on the efficient ccm mold featuring high casting speed. and following the study relative technical measures are put forward, which ensure an increase of the ccm casting speed

    文摘:分析了攀鋼板坯連鑄結晶器在使用中出現的問題及其產生原因，對以高拉速為核心的高效連鑄結晶器結構進行了研究，提出了相應的技術措施，確保了攀鋼連鑄機拉速的提高。
  8. The continuous kerbing method is ahigh production, cost effective alternative to the rpecast method. for that reason tsl construction have chosen the arrow 750xl slipformer

    連續鋪設方法取代預澆鑄方法實現高效率、低成本。因此， tsl建築公司才選擇了箭牌750xl型路緣機。
  9. The intermediate magnesium - clad paint is the must material for high efficiency casting taking the place of thermal insulation slab, which has advantages as follows : easy painting, no crack, anti - corrosion, easy disintegration and help improving steel liquid quality etc

    中間包鎂質塗料是替代絕熱板，實現高效連鑄的必備材料，具有易塗抹、不開裂、耐侵蝕、易解體並能提高鋼液質量等優點。
  10. The series of dm tundish coating is necessary materials for replecting insulating board and realizing hign - effcieney continuous casting, they have the properties of coating uncracking, resist corrosion, decomposing, etc. compared with insulating board, they are not only have the low cost of per ton steel materials but also reduce the impurity in liquid steel, increasee the purity and improve the perfoumnce of liquid steed

    中間包塗料是替代絕熱板，實現高效連鑄的必用材料，具有易塗抹、不開裂、耐侵蝕、易解體等特點，與絕熱板相比不僅降低噸鋼耐材成本，而且減少鋼液中非金屬雜質，提高鋼液的純度，改善鋼的性能。
  11. After the optimization of optimization of its production mix and upgrade of its business by persisting in the strategy of " make leading toadvantages ", - tonggang has owned a series of sophisticated process equpments, such as sec - ondary refining, high efficient continuous casting, sections continuousroll - ing, small sections rolling, hith speed wire rode rolling steel strand produ - ction lines and so on. it strengthens the developing momentum of the enterprise in the new century

    通鋼集團堅持實施品牌戰略，走精品名牌發展之路，依託科技進步，優化產品結構，推進產業升級，現已形成以轉爐精練、高效連鑄、型鋼連軋高速線材、小型連軋、鋼絞線等為主體的具有國際、國內領先水平的工藝裝備，全面增強了企業發展后勁。
  12. Based on the analysis of developmental characters of modem eaf technology in the past forty years, it is pointed out that modem eaf technology has developed around the goal of shortening tap - to - tap time to meet the rapid continuous casting rhythm and the integrated control theory of modem eaf melting tap - to - tap time is proposed

    摘要在分析40年來國內外現代電弧爐煉鋼技術發展特點的基礎上，指出現代電弧爐煉鋼技術是圍繞縮短冶煉周期以滿足高效連鑄節奏要求這一核心發展起來的，提出了現代電弧爐冶煉周期的綜合控制理論。
  13. Abstract : based on the hypotheses of three - piece straightening curve. it isverified that the method for using little deformation condition was true with accurate solution of three - piece straightening curve. the mechanics behavior of slab was analyzed in regard to the creep properties of high temperature slab. the results show that the strain, the strain velocity and the stress varied so smoothly that the inner crack was prevented. technical renovation is carried on by adjusting the displacement of rolls and by using the accurate solution of three - piece straightening curve

    文摘:基於三段矯直曲線應變速率的假設，通過計算三段矯直曲線的精確解，驗證了使用小變形條件的正確性;考慮高溫鑄坯蠕變性能，對鑄坯的力學行為進行了分析，得出了使用三段矯直曲線方法，鑄坯應變速率、應力及應變在矯直區內變化較為平緩，可有效避免鑄坯內裂紋的形成;使用本文三段矯直曲線精確解，調整輥列位置，可進行連鑄機的在線技術改造。
  14. Because have a series of generally acknowledged merits, such as high efficiency, high quality, high lumber recovery with low costs, etc. to cast steel in succession, every country in the world, which is developping energetically, cast and liken improving to optimizing for the structure of steel factory, strengthen the key link that the market fought for ability and increasing economic efficiency as the central link

    由於連續鑄鋼具有成本低、高效率、高質量、高成材率等一系列公認的優點，世界各國都在大力發展，把提高連鑄比作為鋼廠結構優化，增強市場競爭能力和提高經濟效益的中心環節。
  15. Round coating graphite moule ( for horizontal continuous casting of copper, aluminum, gold, silver, stainless steel and carbonated steel )

    多孔圓形、異形塗層石墨模具，用於中、小型的型材水平連續鑄造，可有效提高工效。
  16. A new control system based on windows os for horizontal cold chamber die casting machine mode " j11280 " is designed. by analyzing the windows 9x os principle and j11280 ' s performance demand, it resolves the real - time control and device - dependence problem. using multi - thread, dll, shared - memory and activex technology enhance the efficiency and performance

    將windows操作系統引入j11280型臥式冷室壓鑄機控制系統中，通過分析windows系統的運行機制和壓鑄機的性能指標，解決了控制系統的實時性和設備相關性問題，使用多線程、動態連接庫、共享內存及activex技術提高了系統的效率和健壯性。
  17. Based on the summarization of current situation of fluorine - free mould fluxes at home and abroad, the main problem during decreasing fluorine for high carbon steel and peritectic steel mould fluxes was analyzed, which includes the stability between viscosity and temperature at high temperature as well as effective control of crystallization properties

    摘要綜述了國內外無氟連鑄結晶器保護渣發展狀況，分析了目前高碳鋼和包晶鋼（特別是亞包晶鋼）用保護渣降氟過程中面臨的主要問題：高溫時粘度溫度特性的穩定性以及保護渣結晶性能的有效控制。
分享友人
分享到 Line

分享到臉書