高溫合成法 的英文怎麼說

中文拼音 [gāowēngěchéngfǎ]
高溫合成法 英文
shs
  • 高 : Ⅰ形容詞1 （從下向上距離大; 離地面遠） tall; high 2 （在一般標準或平均程度之上; 等級在上的） above...
  • 溫 : Ⅰ形容詞（不冷不熱） warm; lukewarm; hot; gentle; mild Ⅱ名詞1 （溫度） temperature 2 （瘟） acute ...
  • 合 : 合量詞（容量單位） ge, a unit of dry measure for grain （=1 decilitre）
  • 成 : Ⅰ動詞1 （完成; 成功） accomplish; succeed 2 （成為; 變為） become; turn into 3 （成全） help comp...
  • 法 : Ⅰ名詞1 （由國家制定或認可的行為規則的總稱） law 2 （方法; 方式） way; method; mode; means 3 （標...
  • 高溫 : high temperature; elevated temperature; hyperthermia; megatemperature; inferno
  1. Taking the andalusite from south africa and alumina fiber as raw materials, adding aluminum sulphate as binder, fabrication and properties of alumina fiber reinforced andalusite composite was studied through wet dispersion, mould pressing and sintering processes

    以紅柱石和氧化鋁纖維為原料，用硫酸鋁作為結合劑，經過分散、混合、半干法成型、高溫燒成工藝，對氧化鋁纖維增強紅柱石基復合材料的制備及性能進行了研究。
  2. The al matrix composites by reaction synthesis put up high mechanical behavior, well high - temperature properties and excellent wearing quality but the existent difficulties lie in that homogenizing method is not perfect, fundamental research to growth mechanism is absent and the concomitance compound come from reaction is difficult to eliminate at present

    反應合成的鋁基復合材料具有常溫力學性能高、高溫性能好和耐磨性突出的優點，而存在的主要研究難題則是整個材料均質化方法不理想、生長機制等基礎理論研究缺乏、反應伴生的化合物難以控制等。
  3. The brewing characteristics of shaoxing wine were presented in the following eleven aspects : the uniqueness of adjunct materials and the variety of different wine, the treatment of soaking rice at low temperature for a long time, the variety of fermentation state, the characteristics of rice wine broth, the variety and complexity of microorganisms, the uniqueness of inoculation and strain preservation, the process of mixed fermentation of yeast and lactic acid bacteria ( e. g. the concurrence of saccharification, yeast fermentation and lactic fermentation ), the over - mixing of different liquors, the high sterilization temperature, and the storage of produced wine

    摘要該文從11個方面論述了紹興黃酒的釀造特點，即配料的特殊性和酒種的多樣性；低溫長時間浸米；發酵狀態的多樣性；黃酒醪的發酵特點；微生物的多樣性，復雜性；接種方式獨特；菌種保存方法獨特；酵母與乳酸桿菌協同作用的混合發酵并行的過程（即邊糖化、邊酵母發酵、邊乳酸發酵同時進行的三邊發酵） ；酒液勾兌；較高的滅菌溫度；成品酒的貯存。
  4. The methods - three dimension fabric - enforced laminates, and sparse fabric - enforced laminates, layer - enforced laminates ? to enhance the interlaminar toughness of fabric - reinforced laminates were discussed in this paper. the stitching method to enhance interlaminar toughness of stitched - laminates was mainly discussed in this paper based on our research and experiment. the middle - alkali glass fabric used as enforced - material with thickness of 0. 2mm, 3 section 600 deniner kevlar yarn is used as stitching thread in this research, which improved lock stitching way and different kinds of stitching mode were adopted

    以提高層合板復合材料的層間斷裂韌性（能量釋放率）為目標，採用中堿玻璃布為增強材料，對疊層后的玻璃布，採用凱芙拉縫合線、改進的鎖型縫合方法、不同的縫合工藝進行了縫合；基體採用的是不飽和樹脂，固化劑為過氧化甲乙酮，促進劑為環烷酸鈷液；在室溫下採用真空輔助rtm （ resigntransfermolding ）成型固化方法，製作了不同縫合工藝的玻璃布增強復合材料層合板。
  5. The questions the researcher concerned are which system will be chosen and how to obtain the good lithium ionic conductor materials, which is the basic departure of the paper. the addition of second phase in composite can change the interface structure and the conduction mechanism, improve the matrix conductivity and other function such as the sintering, crisping and so on, so the research of composites are an interesting field of the ionic conductors. the synthesis of lithium ionic conductor is often by solid state reaction, but this method needs high temperature and leads to the volatility of lithium which not only causes the drift of the compounds but gets the no well - distributed materials

    研究者所關注的問題是選擇新的體系進行研究，以期得到性能更好的鋰離子導體材料，這也正是本論文的基本出發點；復合離子導體中第二相的加入改善了基質的界面結構和導電機制，不僅可以提高基質材料的電導率，還可以在一定程度上改善材料的其它性能，如燒結性能、脆性和機械強度等。因此復合材料的研究是離子導體一個有廣闊前景的發展方向；合成鋰離子導體，特別是成分復雜的體系以傳統的固相合成法為主，但這種方法需要較高的溫度，容易引起鋰的揮發，從而造成產物組成的偏移，而且不易得到顯微結構均勻的材料。
  6. The researching work include three aspects : 1 ) after selecting primary material system, the polymer coating process were optimized. the polymer - coated high - temperature alloy powder has been developed on the basis. 2 ) based on sintering and orthogonal experiments, the influence of the prototyping elements on prototyping properties have been initially studied, and the optimal prototyping parameters of this material has been obtained finally

    本文主要研究內容為： （ 1 ）選擇合適的包覆材料體系，對鉬粉的包覆工藝進行了優化實驗，在此基礎上開發了適合於激光燒結成型用覆膜高溫合金粉末材料； （ 2 ）通過激光燒結成型實驗，運用正交實驗方法，系統地研究了燒結工藝參數對成型質量的影響關系，在此基礎上確定了覆膜高溫合金粉末最佳燒結成型工藝參數； （ 3 ）對激光成型件進行了后處理工藝實驗，得到了優化的后處理工藝規程，並製作了合格的后處理樣件。
  7. Self - propagating high - temperature synthesis ( shs ) is a new technology for preparing inorganic pigments, which is superior to the traditional method. shs has excellent prospects

    摘要利用自蔓延高溫合成技術合成無機顏料是制備顏料的一種新技術，優于傳統的固燒結法，是一項具有發展前途的技術。
  8. The influence that the zr / ti ratios have on the ceramic crystal structure and its properties are studied through the research carried out about the relative respects of the fabricated samples. the increase of zr / ti ratio can result in the crystal structure transformation from the tetragonal to the rhombohedral, it can also induce the weakness in the stability of the ceramic crystal structure, for example, the drop in the curie temperature. in order to enhance the relative low mechanical quality factor of pzn - pzt system piezoceramics, component addition pb ( mn1 / 3sb2 / 3 ) o3 ( hereafter abbreviated as pms ) are introduced in to form a new psudo - tetragonal system ceramics

    為獲得具有高的機電耦合系數kp ，高的機械品質因數qm的高性能壓電陶瓷，採用二次合成法制備了不同zr ti比的鈮鋅酸鉛-鋯鈦酸鉛基（ pzn - pzt ）三元系壓電陶瓷材料，研究了zr ti比變化對陶瓷結構和性能的影響規律，發現zr ti比增大除了可以使陶瓷的相結構由四方相向三方相轉化外，還降低了陶瓷的結構的穩定性，使tc溫度下降。
  9. Yttrium aluminum garnet ( y3al5o12, yag ) is not only a very important laser material, but also a high - temperature structural material and a fluorescence material. in this paper, the discussions are mainly focused on the synthesis of yag powders by co - precipitation method, self - propagating high - temperature synthesis and mixed method, powder ' s property, etc. in the co - precipitation method, the precursor was produced by adding a mixed a1 ( no3 ) 3 and y ( no3 ) 3 solution to nh4hco3 solution. yag can be obtained by heating the precursor at looo ' c for 5 hours without the formation of yam and yap transition phase

    釔鋁石榴石（ y _ 3al _ 5o _ 12 ，簡稱yag ）是一種重要的激光基質材料，同時它還作為高溫材料和熒光材料得到了廣泛的應用，本文主要討論了化學共沉法、燃燒法制備yag的超微粉的工藝，並對yag超微粉的性能及物相進行了分析；採用固相合成法制備了ca ， ca ： yag系列陶瓷，並對其結構和性能進行了討論。
  10. Abstract : according to the characterestic of resistance furnace temperature control, temperature rising one - way control, large time delay and time - variation of parameter, using method of fuzzy compositional rule of inference establish fuzzy model and design fuzzy cntroler. in order to increase control system precision, it gives a fuzzy variable k, and sets parameter self - adjusting fuzzy control system. this system can on line self - adjusting controller parameters according to the error and variations of the error. it makes the system steady precision improved

    文摘:根據電阻爐溫控制的特點，即只有升溫單向控制、滯后較大且具有參數時變性，利用模糊推理合成法建立模糊模型並進行模糊控制器設計，為提高模糊控制的精度，引入模糊變量k ，構成參數自調整模糊控制系統.該系統可根據誤差和誤差變化在線自動調整控制器參數，使系統的穩態精度得到改善
  11. According to the characterestic of resistance furnace temperature control, temperature rising one - way control, large time delay and time - variation of parameter, using method of fuzzy compositional rule of inference establish fuzzy model and design fuzzy cntroler. in order to increase control system precision, it gives a fuzzy variable k, and sets parameter self - adjusting fuzzy control system. this system can on line self - adjusting controller parameters according to the error and variations of the error. it makes the system steady precision improved

    根據電阻爐溫控制的特點，即只有升溫單向控制、滯后較大且具有參數時變性，利用模糊推理合成法建立模糊模型並進行模糊控制器設計，為提高模糊控制的精度，引入模糊變量k ，構成參數自調整模糊控制系統.該系統可根據誤差和誤差變化在線自動調整控制器參數，使系統的穩態精度得到改善
  12. Three series of absorbent powder samples were synthesized by the high - temperature solid - state method : the first is that fe / ti mol proportion in the material changes regularly ; the other one is that different thuliums doped in the same absorbent ; the last series is the absorbent was doped by different content thulium. the permittivity and permeability of the modified ilmenite absorbents were systematically measured

    通過使原料中金屬離子的摩爾比例（ fe ti ）作有規律變化、在同一基質中摻雜同含量的不同稀土金屬以及改變同種稀土金屬的摻雜量等手段，採用高溫固相合成法制備了不同系列可供進行吸波性能研究的鈦酸亞鐵類化合物吸收劑。
  13. The applications field of fgm include aerospace, electron, chemistry, biology and medicine fields ; the composition change also from metal / ceramic to metal / metal, metal / alloy, non - metal / non - metal and non - metal / ceramic. moreover, various methods including powder metallurgy, self - propagating high - temperature synthesis ( shs ), chemical and physical vapor deposition ( cvd and pvd ), electrodeposition, laser cladding method, plasma sputtering and sol - gel method have been studed. metal organic chemical vapor deposition ( mocvd ), using chemical vapor deposition of metal organic compounds, is an effective method for acquiring special function materials and membrane

    功能梯度材料是21世紀最有發展前景的新型材料之一，其用途已由原來的宇航工業，擴大到核能源、電子、化學、生物醫學等領域；其組成也由金屬?陶瓷發展成為金屬?金屬、金屬?合金、非金屬?非金屬、非金屬?陶瓷等多種組合；其制備方法主要包括粉末冶金法，自蔓延高溫合成法（ shs ） 、氣相沉積法（ cvd和pvd ） 、電沉積法，激光熔覆法，溶膠?凝膠法（ sol - gel ）等。
  14. The pure active material can be sintered in 5 hours by using solid - state method

    用高溫固相法5h就能合成出純相活性物質。
  15. Several methods on joining of ceramic / metal are reviewed. the joi ning of ceramic / metal brazing, partial transient liquid bonding and shs welding on power engineering and high - temperature composite of advanced jet engine, are emphasized

    綜述了陶瓷與金屬連接的幾種方法，重點討論了對未來動力工程和先進發動機有重要意義的陶瓷與金屬釬焊連接、部分瞬間液相連接及自蔓延高溫合成（ shs ）連接。
  16. In this paper lifepo _ 4 powders were prepared via solid - state reactions mehtod that involve multiple steps at high temperatures. the effects of synthesis conditions on structure and electrochemical behavior of lifepo _ 4 were studied

    採用高溫固相法制備lifepo _ 4 ，研究了合成條件對lifepo _ 4結構和電化學性能的影響，並嘗試了對材料進行摻雜改性。
  17. With arthogonality experiment method and xrd, tg - dta, the luminescent properties and the factors of influence on them were studied, and the optimum condition of sintering was determined

    運用正交實驗方法，藉助xrd 、 tg - dta等現代測試手段，對影響其發光性能的因素進行了研究，確定了高溫固相法合成該材料的最佳條件。
  18. In this paper, the principles and the main processing of new methods for preparation of ferrite powders are discussed, including self - propagating high - temperature synthesis, low - temperature combustion synthesis, mechanochemical synthesis, hydrothermal synthesis, freeze drying and supercritical fluid drying

    綜述了鐵氧體粉料的新型制備方法的原理和主要工藝過程，包括自蔓延高溫合成法、低溫燃燒合成法、機械化學合成法、水熱法、冷凍乾燥法和超臨界流體乾燥法等。
  19. Abstract : in this paper, the principles and the main processing of new methods for preparation of ferrite powders are discussed, including self - propagating high - temperature synthesis, low - temperature combustion synthesis, mechanochemical synthesis, hydrothermal synthesis, freeze drying and supercritical fluid drying

    文摘:綜述了鐵氧體粉料的新型制備方法的原理和主要工藝過程，包括自蔓延高溫合成法、低溫燃燒合成法、機械化學合成法、水熱法、冷凍乾燥法和超臨界流體乾燥法等。
  20. 0. 4 absorbents are prepared by high - temperature solid - state reaction. the influence of doping potassium on the crystal structure of the prepared absorbents is studied by comparison of their xrd patterns

    為反應物，採用高溫固相合成法在k元素摻雜的情況下，制備了一系列可在高溫460650下直接吸收co
分享友人
分享到 Line

分享到臉書