高溫工藝氣體 的英文怎麼說

中文拼音 [gāowēngōngyìqìtǐ]
高溫工藝氣體 英文
hot process gas
  • 高 : Ⅰ形容詞1 （從下向上距離大; 離地面遠） tall; high 2 （在一般標準或平均程度之上; 等級在上的） above...
  • 溫 : Ⅰ形容詞（不冷不熱） warm; lukewarm; hot; gentle; mild Ⅱ名詞1 （溫度） temperature 2 （瘟） acute ...
  • 工 : Ⅰ名詞1 （工人和工人階級） worker; workman; the working class 2 （工作; 生產勞動） work; labour 3 ...
  • 藝 : Ⅰ名詞1 （技能; 技術） skill 2 （藝術） art 3 [書面語] （準則） norm; standard; criterion4 [書面語...
  • 氣 : Ⅰ名詞1 （氣體） gas 2 （空氣） air 3 （氣息） breath 4 （自然界冷熱陰晴等現象） weather 5 （氣味...
  • 體 : 體構詞成分。
  • 高溫 : high temperature; elevated temperature; hyperthermia; megatemperature; inferno
  • 氣體 : gas; gaseous fluid
  1. Using jgp560c magnetron sputtering equipment, cu / ag film are deposited on cd1 - xznxte substrate by dc magnetron sputtering in order to get the influences of the main experiments parameters such as sputtering power, gas flow, vacuum air pressure, magnetoelectricity power and substrate temperature on deposition rate of film, discovered that dc sputtering power is the most key factor influencing the deposition rate

    在jgp560c型超高真空多功能磁控濺射鍍膜機上，採用直流磁控濺射法在cdznte晶體上制備出cu ag合金薄膜，揭示了氣體流量、直流濺射功率、勵磁電源功率、工作氣壓和襯底溫度等工藝參數對沉積速率的影響規律。結果表明濺射功率對沉積速率的影響最大，隨濺射功率的增大沉積速率快速增大。
  2. The factory is specialized in the manufacture of the whole set of testing equipment fo gas - vase ( do not sew, fuse, liquefied petroleum gas, natural gas etc. spirit bottle ), various air infuses set, remitting to flow row and to infuse tongs ; the stainless steel is four fluorine soft tubes, the industrial air ( the pack ) gathers to pack, modernizing industrial factory premises concentration to provide spirit system and assisting a piece : decompression machine, safe valve, allotment box ; and standard air, hybrid air, special kind air, high install craft device purely and gaseously ; the automation cuts over, going together with to compare to equip automatically ; various air valve door and accessories, spirit bottle enclosure ; the low temperature equipments liquid pump ; vaporize a machine ; the low temperature closes valve ; the ripples takes care of to wait a series product

    本廠專業設計生產製造各種氣瓶檢驗成套設備（無縫，溶解，乙炔，液化石油氣，天然氣等氣瓶） ，各種氣體充灌臺，匯流排及充灌夾具;不銹鋼四氟軟管，工業氣體（充裝）集裝箱，現代化工業廠房集中供氣系統及輔件:減壓器，安全閥，分配箱;以及標準氣體，混合氣體，特種氣體，高純氣體的配置工藝裝置;自動化切換，自動配比裝置;各種氣體閥門及配件，氣瓶附件;低溫設備液體泵;汽化器;低溫截止閥;波紋管等系列產品
  3. On the base of the analysis on the advanced technology of hard ferrite in foreign country, the main procedures of preparing hard ferrite pre - sintering material are determined as follows : first, the ferrite oxides coming from the main cold rolling line and strontium carbonate are conveyed to storage tank by gas power and weighed automatically according to the demands of constituent composition. and then they are mixed and grinded by using method of wet treatment. finally the mixtures is transported to the devices of storage by transporting pump

    在分析國外先進的永磁鐵氧體生產工藝的基礎上，確定了生產高檔永磁鐵氧體預燒料的主要過程：首先，利用攀鋼冷軋鐵紅為主要原料，將氧化鐵紅及碳酸鍶採用氣力輸送至貯料料倉，經自動稱量裝置，按工藝配方稱量後分別由氧化鐵紅及碳酸鍶發送罐氣力輸送進入預混攪拌筒加水攪拌，然後再送入混磨機濕法混磨；最後，混合物經輸送泵輸送至料漿存儲裝置，經定量進料泵定量輸送至回轉窯進行濕法預燒，預燒料經緩冷至室溫后，再球磨。
  4. The raw materials, the composition, the time of milling, the calcining temperature, the different additives, the sintering temperature and the sintering parameters were investigated. the result showed : it was advantaged to obtain high initial permeability mnzn ferrite with stable frequency characteristic using high - purity raw materials ; in order to obtain mnzn ferrite with high properties, we must control strictly the composition ; it could improve the properties of mnzn ferrite by optimizing calcining temperature. the lower calcining temperature made the permeability higher, and the higher calcining temperature could promote the frequency characteristic of permeability ; we chosen the right time of milling according to the requirement of power diameter ; in order to improve the properties of mnzn ferrite, it is necessary to add effective additives. in this dissertation, the influence of bi2o3 、 moo3 、 k2co3 、 co2o3 were investigated ; the sintering temperature, the time of heat - retaining and sintering parameters were the key factors of preparing high permeability mnzn ferrites

    研究結果表明:採用高純度的fe2o3有利於獲得高起始磁導率且頻率特性優良的鐵氧體;為了制備所需性能的鐵氧體，需要嚴格控制配方中各種原材料的含量，優化配方;由於粉體活性受預燒條件的影響，所以對不同要求的鐵氧體選擇的預燒條件就不一樣，適當降低預燒溫度有利於獲得較高的起始磁導率，而為了獲得良好的頻率特性可以適當地提高預燒溫度;根據對粉體顆粒粒徑的不同需求，可以選擇不同的球磨時間;而有效的添加劑是改善材料性能的必要條件，本文在添加劑的研究中主要對bi2o3 、 moo3 、 k2co3 、 co2o3的影響分別作了詳細地討論;燒結溫度、保溫時間和燒結氣氛是高磁導率mnzn鐵氧體制備最關鍵的工藝，適宜的燒結工藝可以獲得理想微結構和組成，從而得到高性能的鐵氧體材料;而從材料的微結構上來看，要提高材料的截止頻率，就要適當地細化晶粒、增加晶粒內部的氣孔。
  5. The quality of buffer layer and thin films was analyzed by afm, xrd, rheed and xps respectively. the effect of the experimental parameters such as carbonization time, working pressure, c source gas flow rate, carbonization temperature, different carbonization gas and substrate on the carbonization process was studied firstly. it was observed that the size of particles was increased with the increase of carbonization time and the rms was opposite, but the trend was reduced while the carbonization time was long enough ; the size of particles was increased with the increase of working pressure too, and choosing a proper working pressure could get a smooth surface ; the size of particles was unobviously changed while the gas flow rate was low, but it was notability increased with the increase of gas flow rate while the gas flow rate was high enough, and a smooth surface could be also obtained by choosing a proper gas flow rate ; with the increase of carbonization temperature, the size of particles was increased, the rms is decreased and a good single - crystalline carbonization layer could be obtained, but a rough surface was formed at a excessive high temperature ; the rms of

    對于碳化工藝，側重研究了碳化時間、反應室氣壓、 c源氣體的流量、碳化溫度以及不同種類的c源氣體、基片取向等因素對碳化層質量的影響，研究結果表明:隨著碳化時間的增長，碳化層的晶粒尺寸隨之變大，表面粗糙度隨之降低，但當碳化到一定時間之後，碳化反應減緩，碳化層的晶粒尺寸以及表面粗糙度的變化幅度變小;碳化層的晶粒尺寸隨反應室氣壓的升高而變大，適中的反應室氣壓可得到表面比較平整的碳化層;在c源氣體的流量相對較小時，碳化層的晶粒尺寸隨氣體流量的變化不明顯，但當氣體流量增大到一定程度時，碳化層的晶粒尺寸隨氣體流量的增大而明顯變大，同時，適中的氣體流量得到的碳化層表面粗糙度較低;碳化溫度較低時，碳化層的晶粒取向不明顯，隨著碳化溫度的升高，碳化層的晶粒尺寸明顯變大，且有微弱的單晶取向出現，但取向較差，同時，適中的碳化溫度可得到表面平整的碳化層;相比于c _ 2h _ 2 ，以ch _ 4作為c源氣體時得到的碳化層表面平整得多;比起si （ 100 ） ，選用si （ 111 ）作為基片生長的碳化層的晶粒取向一致性明顯更好。
  6. Our company adopts the metal honeycomb or the metal network board carrier, with special coating coating technology and processing technology, prepare different forms, the all kinds of catalysiseses of specification, used in petrol exhaust. with the characteristic of light in low temp, purification efficiency high and long life etc. main technological schemes as below

    通用汽油機凈化器我公司採用金屬蜂窩或金屬網板載體，通過特殊的塗層塗覆技術及加工工藝，可制備不同形狀規格的各類催化凈化器，用於汽油機的排氣凈化，具有起燃溫度低凈化效率高使用壽命長等特點。
  7. This paper studies the application of inductively coupled plasma ( icp ) technology to the etching compound semiconductor insb - in film. by means of single probe and double probe, the ion density and electron temperature of chamber ( 30mm and 50mm in height respectively ) under varied process condition were diagnosed. the spatial distribution of the axial position of the two parameters and the varied curve that the two parameters varies with the power and air pressure are obtained

    利用單探針和雙探針診斷30mm高反應室和50mm高反應室在各種工藝條件下的離子密度和電子溫度，得到這兩個參數在反應室軸向位置的空間分佈、隨功率和氣壓的變化曲線、頂蓋接地和反應室體積對它們的影響，結果表明離子密度為10 ~ 8 10 ~ （ 10 ） cm ~ （ - 3 ） ，電子溫度在4 10ev之間；當頂蓋接地時，該處的等離子體密度明顯大於不接地；在同樣條件下， 50mm高反應室內的離子密度明顯大於30mm高反應室。
  8. Abstract : by means of analysing the difference of fuel feature of organic solid wastes and coal ， this paper discusses low pollution ， low corrosion and high efficiency technology of organic solid waste incineration from several factors including controls of technology ， temperature ， residence time, air ratio and the use of the additives and flue gas

    文摘:通過分析固體有機廢物與煤的燃料特性的不同及其對燃燒的影響，從工藝控制，溫度控制，停留時間選擇，送風控制，添加劑以及煙氣循環使用等方面探討低污染、低腐蝕、高效固體有機廢物的焚燒技術。
  9. With a decade of years of research and manufacture history on boilers and pressure vessel, complete quality control system, advanced production equipments, as well as well managed after sale service, " changcheng " autoclave becomes a brand trusted by many users, and has been used in fishery, chemical industry, glass industry, medicine industry, textile printing, heat insulating material, papermaking, timbering, civil construction and other industries

    十多年鍋爐壓力容器設計技術的潛心研究和製造歷史，完善的質保體系、先進的工藝裝備、無可挑剔的善後服務，鑄就「常成」蒸壓釜眾多用戶依賴的產品品牌，廣泛應用於漁業、化工、玻璃、醫藥、紡織印染、保溫材料、造紙、木材、加氣混凝土砌塊、粉煤灰砂、高強度水泥電桿、石膏蒸壓等眾多工業領域。
  10. As a engineer, i have researched the technology of the deposition of the pyrolytic graphite grid ’ s rough in detail and deeply, in order that xuguang electric ltd. co. achieves the producing from the deposition of the pyrolytic graphite grid ’ s rough to grid. in this research, propane and nitrogen gases has been used in the deposition of the pyrolytic graphite grid ’ s rough at about 1800 and in vacuum

    為了使旭光電子股份有限公司順利實現從熱解石墨柵極毛坯沉積到柵極成品的生產，本人作為工藝研究人員，對熱解石墨柵極毛坯沉積工藝進行了詳細、深入的研究。在本課題研究工作中，採用了丙烷有機碳氫化合物氣體和稀釋用氮氣、氬氣，在高溫1800左右的真空條件下試驗研究了熱解石墨柵極毛坯的沉積。
  11. The process of the liquid phase sinter was studied, the study showed that the mo - cu sinter could gain 95 % - 97 % relative density when the relative density of the flan was 70 % - 80 %, the sinter temperature was 1100 - 1200, the sinter time was 80min - 100min and the sinter atmosphere was hydrogen

    本文通過對mo - cu粉末生坯的燒結工藝研究得出，粉末生坯相對密度為70 80 ，燒結溫度為1100 1200 、等溫時間為80 120min 、氫氣保護氣氛下，可制備出具有高緻密度的mo - cu粉末燒結體。
分享友人
分享到 Line

分享到臉書