高溫馬氏體 的英文怎麼說

中文拼音 [gāowēnmǎshìtǐ]
高溫馬氏體 英文
high temperature martensite
  • 高 : Ⅰ形容詞1 （從下向上距離大; 離地面遠） tall; high 2 （在一般標準或平均程度之上; 等級在上的） above...
  • 溫 : Ⅰ形容詞（不冷不熱） warm; lukewarm; hot; gentle; mild Ⅱ名詞1 （溫度） temperature 2 （瘟） acute ...
  • 馬 : Ⅰ名詞1 [動物學] （哺乳動物） horse 2 （象棋棋子） horse one of the pieces in chinese chess3 （姓...
  • 氏 : 氏名詞1 （姓） family name; surname 2 （放在已婚婦女的姓后 通常在父姓前再加夫姓 作為稱呼） née : ...
  • 體 : 體構詞成分。
  • 高溫 : high temperature; elevated temperature; hyperthermia; megatemperature; inferno
  • 馬氏體 : marte ite
  1. 5 ) as the deformation strain increases the reverse transformation temperature and thermal hystersis of tini film increase on the first heating, while the martensitic transformation temperature decreases and r phase transition temperature is constant

    隨預應變量增大， tint薄膜的第一次逆相變溫度升高，相變熱滯增大，馬氏體相變溫度降低， r相變溫度無明顯變化。
  2. The lath width of martensite can be fined noticeably by pre - strained quenching at non - dynamic recrystallization to approach nanometer magnitude ( the average width is 120nm )

    採用非動態再結晶溫度下的預應變-淬火，提高馬氏體相變形核率，可以超細化馬氏體的板條晶片寬度，使之接近納米量級水平（平均寬度達到120nm ） 。
  3. Abstract : recent experimental investigations have demonstrated that the pre - deformation of shape memory alloys results in martensite stabilization opposing reverse transformation, hence leading to the expansion of transformation hysteresis

    文摘:形狀記憶合金經適當溫度下的塑性變形可以有效地提高馬氏體的穩定性，從而使相變滯后得以大幅度提高。
  4. It is indicated that the relaxation of elastic energy stored during the forward martensitic transformation is responsible for the expansion of transformation hysteresis, which is in good agreement with experimental results associated with the hysteresis enlargement by deformation of niti, niti - based and cualni shape memory alloys

    結果表明，塑性變形產生的位錯以及變形的第二相顆粒對逆馬氏體相變溫度的提高具有一定作用，但塑性變形導致應變能釋放才是形變提高形狀記憶合金相變滯后的主導因素。
  5. The effect of plastic deformation and elastic strain energy induced by pre - strain on the nucleation of martensitic transformation of low alloy ultra - strength steel sosimncrmov had been studied by pre - strain quenching in austenite state. the control over deformation magnitude and deformation temperate as well as loading pattern was performed to adjust the storage of elastic strain energy in steel before martensitic transformation, using the type of geeble - 1500 thermal analogue test machine

    使用gleeble - 1500型熱模擬機，對低合金超高強度鋼30simncrmov實施奧氏體預應變淬火處理，通過控制形變量、形變溫度和加載方式，調整鋼中馬氏體相變前的彈性應變能儲備，研究了預應變所造成的塑性變形與彈性應變能對馬氏體相變的影響。
  6. Standard specification for martensitic stainless steel bars for high - temperature service

    高溫設備用馬氏體不銹鋼棒材的標準規范
  7. In succession, tini thin film is deposited on single - crystal silicon substrate using optimized parameters utilizing sputtering, and its transformation temperature ( a * ) is 72 ? indicated by dsc curve after being annealed in an ultra - high vacuum ( uhv ) chamber. in addition, the composition of the silicon - based tini film was analyzed by an energy dispersive x - ray spectroscopy ( eds ), and the ti content in the film is approximately 51at %

    按照改進的工藝參數，在單晶硅襯底上濺射-淀積了tini薄膜，並進行了超高真空退火， dsc法測得其馬氏體逆相變峰值溫度為72 ，利用能譜分析（ eds ）技術測得其ti含量約為51at ，通過對非晶tini薄膜與單晶硅襯底之間的界面進行eds及x射線衍射（ xrd ）分析，發現在用大功率（ 2000w ）直流磁控濺射法制備tini薄膜過程中，存在ti 、 ni與si的雙向擴散，發生了界面反應，並有三元化合物ni _ 3ti _ 2si生成。
  8. Steel forgings for pressure purposes - part 2 : ferritic and martensitic steels with specified elevated temperature properties

    壓力容器用鋼鍛件.第2部分:規定高溫性能的鐵素體和馬氏體鋼
  9. Steel forgings for pressure purposes - part 2 : ferritic and martensitic steels with specified elevated temperature properties including corrigendum ac : 2000 ; german version en 10222 - 2 : 1999 ac : 2000

    承壓鋼鍛件.第2部分:具備特定高溫性能的鐵素體和馬氏
分享友人
分享到 Line

分享到臉書