高速砂輪 的英文怎麼說
中文拼音 [gāosùshālún]
高速砂輪
英文
high eed wheel- 高 : Ⅰ形容詞1 (從下向上距離大; 離地面遠) tall; high 2 (在一般標準或平均程度之上; 等級在上的) above...
- 速 : Ⅰ形容詞(迅速; 快) fast; rapid; quick; speedy Ⅱ名詞1 (速度) speed; velocity 2 (姓氏) a surna...
- 砂 : 名詞(沙子) sand; grit
- 輪 : Ⅰ名1 (輪子) wheel 2 (像輪子的東西) wheel like object; ring; disc 3 (輪船) steamer; steamboa...
- 高速 : (高速度) high speed; high velocity (hv); high rate; swift; fast; express; high-speed
-
Grinding wheel continues with an infinite number of hard, sharp and refractory grits on edge surface at a high speed of swing operation to cut and grind over the surface of work piece, and unceasing self - sharpening grains and pore continue to grind a tool for every kind of material
砂輪是經由高速回轉運作中,以其在外緣表面植無數上千萬之硬銳耐溫之小磨粒連續在工作物表面切削磨除,且不斷的自生銳利顆粒與磨屑空隙氣孔,繼續對各種材料做磨削工作的一種研磨工具。Grinding feature is to use work piece for a slow - speed operation, and wheel spindle selects a high - speed revolution and offers a minor amount of in - feed to cooperate with mechanical spinde for forward and backward movement for finishing grinding jobs
研磨特性是利用工作物做慢速運轉,而砂輪心軸采高速回轉並給予微量進刀配合機械心軸前後運動完成研磨作業。Under function of impeller with high rotating speed, the used sand will be cast to the wearable junk ring to remove the inert film on surface of the sand via mutual collision and friction between sand and junk ring, impeller and case of machine, sand and sand
工作時舊砂在高速回轉的葉輪作用下,拋向耐磨襯圈,通過砂粒與襯圈葉輪與機盒砂粒與砂粒之間的相互碰撞和摩擦,去除砂粒表面的樹脂惰性膜。Analysis of strength in high speed rough grinding wheel of large diameter
大直徑高速粗磨砂輪的強度分析Suzhou ding lian rubber produce co., ltd located in suzhou wuzhong exports of sujiahang expressway. ding lian is a company specializing in the production of various types of industrial rubber roller and rail roller modern enterprise
蘇州鼎聯橡膠製品有限公司,地處吳中經濟開發區東吳工業園,位於蘇州蘇嘉杭高速吳中出口處,是一家專業生產各式工業用橡膠輥、砂光輪、印刷輪的現代化企業。The results show that, when increasing the feed rate of the grinding wheel, decreasing the rotating speed of the wafer chuck table and using coarser grit grinding wheel, the material removal rate in the wafer rotating grinding increase, the feed rate of the grinding wheel has greater influence on the material removal rate ; when suitably increasing the rotating speed of the grinding wheel, decreasing the feed rate of the grinding wheel and using finer grit grinding wheel, the wafer surface roughness can be reduced ; there exists a critical rotating speed of the grinding wheel ( about 2300rpm ), beyond which the material removal rate evidently decreases and the spindle motor current and wafer surface roughness steeply increase ; when the grit size of the grinding wheel is finer than # 2000, the material removal rate decreases and the wafer surface roughness has no obvious improvement
研究結果表明,增大砂輪軸向進給速度和減小工件轉速,採用粗粒度砂輪有利於提高磨削矽片的材料去除率,砂輪軸向進給速度對材料去除率的影響最為顯著;適當增大砂輪轉速,減小砂輪軸向進給速度,採用細粒度砂輪可以減小磨削表面粗糙度;在其它條件一定的情況下,砂輪速度超過一定值會導致材料去除率減小,主軸電機電流急劇增大,表面粗糙度變差;採用比# 2000粒度更細的砂輪磨削時,材料去除率減小,矽片表面粗糙度沒有明顯改善。Equipped with high speed and high power electric spindle powered by static frequency convertor, featuring low energy consumption and low noise
採用高速大功率電動砂輪軸,由靜止變頻器供電,能耗低,噪聲小。For the development of the high - speed mortar pump, a type of high - speed cam mechanism was put forward ; and its dynamics model was established with the theory of elasticity
為使砂漿泵向高速化方向發展,提出了一種高速凸輪機構,並以彈性理論為基礎,建立了高速凸輪機構的動力學模型。Based on the characteristics of ultrahigh speed grinding, the general selection principle of abrasives, binders, hardness, concentration and structure of ultrahigh speed cbn wheels is discussed
摘要結合超高速磨削的特點,論述超高速cbn砂輪中磨料、結合劑、硬度、濃度、組織的一般選用原則。Emphasis is laid on the importance of the core of ultrahigh speed wheels, design requirement and material selection
重點強調超高速磨削砂輪基體的重要性和設計要求以及材料的選擇。Finally, the position of the ultrahigh speed wheels in ultrahigh speed grinding and our research direction in future are pointed out
最後,指出超高速磨削砂輪在超高速磨削中的地位,並指出努力方向。High speed depressive center wheels are resin - bonded abrasive tool with special fabric reinforcement mesh bearing high tensile strength, shocking and bending, by using with peripheral velocities up to 80m s meet high grinding efficiency and great safety in production
鈸形砂輪,具有較高的抗拉抗沖擊和抗彎強度,使用速度可達80米秒。使用此種產品,效率高而安全。The features of high speed cutter for cbn wheel grind
使用cbn砂輪研磨高速鋼材質刀具的特點:分享友人