高連富的英文怎麼說

中文拼音 [gāolián]
高連富英文
gao lianfu

  • : Ⅰ形容詞1 (從下向上距離大; 離地面遠) tall; high 2 (在一般標準或平均程度之上; 等級在上的) above...
  • : Ⅰ動詞1 (連接) link; join; connect 2 (連累) involve (in trouble); implicate 3 [方言] (縫) ...
  • : Ⅰ名詞1. (資源; 財產) wealth 2. (姓氏) a surname Ⅱ形容詞1. (財產多) wealthy; rich 2. (豐富; 多) rich; abundant

※中文詞彙高連富在字典百科國語字典中的解釋。

  1. Japan ' s highest peak, mt. fuji, is seen at dusk over the shinjuki business district skyscrapers in tokyo on sunday. the 3, 776 - meter dormant volcano is a national symbol for japanese people

    日本第一士山于星期天傍晚俯視東京新宿區的摩天大樓。這座三千七百七十六公尺的休眠火山對日本人而言是國家的象徵。
  2. According to the nb - si phase diagram, the temperature of 1550 ?, which is lower than the eutectoid transformation temperature of nbssi ( 1783 ? ), is chosen for heat - treatment. according to the present conditions of the furfaces, heat - treatment by stages is first proposed for the nb - si system intermetallic composites to keep the furface in good conditions. the results indicate that the equilibrium nb + nbssia dual - phase microstructure of the nb - si system intermetallics forms gradually via such eutectoid reaction as nbasi ? nb + nbssis with the heat - treatment time

    根據nb - si二元相圖,選擇略低於nb _ 3si共析轉變溫度t _ f = 1783的1550對鑄態nb - si系金屬間化合物進行不同時間( 25h - 100h )的熱處理,並根據目前國內和我院熱處理爐的現狀,首次提出採用分段熱處理的方法來解決nb - si合金熱處理溫度續熱處理時間過長而影響熱處理爐壽命的困難。
  3. The control system of mould level is crucial to improve the slab quality in the continuous casting process, pid controller is used in the traditional mould level control, and it has some defaults, such as : at the start - up or finishing period of casting or during the changeover of tundish, pid control has a bad effect, its overshoot is large and its transient time is long ; the erosion of the tundish stopper and the submersed nozzles lead to the accuracy of control become bad ; the abrupt falloff of block in the submersed nozzles makes the level acutely fluctuate, and pid control can not overcome the disturbances resulted from the change of casting speed

    結晶器液位控制系統是提鑄產品質量的關鍵環節,傳統的鑄機液位控制方法採用常規的pid控制,存在如下不足:開始、結束澆注和換中間罐澆注時,控制效果差,超調量大,過渡時間長;塞棒頭和浸入式水口被腐蝕后引起控制精度差;浸入式水口堵塞物的突然脫落所引起的液位劇烈波動;無法克服拉速波動引起的擾動。
  4. He bought the property next to tiffany ' s on new york ' s swanky fifth avenue

    他買下麗的紐約第五大街上鄰近第凡內的一處房產。
  5. Because goods delivery from enterprises to chain shops takes the standard of reducing logistics cost, this paper also distinguish delivery mode of chain shops from direct delivery, points out promoting economic benefits and realizing the reasonable delivery which should first consider selecting right delivery pattern and studying cost discrimination between the two delivery modes, then distinguish the areas of logistics delivery and direct delivery, in order to reduce enterprise cost. running benefits of enterprise are in relation to cost and service of enterprise

    由於企業對各鎖店的送貨以降低物流費用為標準,本文進一步探討了鎖企業的配送模式與直送方式的區別,指出提鎖企業配送的經濟效益,實現配送的合理化首先要合理地選擇送貨方式,研究了兩種送貨方式的成本分歧點,並正確劃分出配送與直送的區域范圍,以降低企業的經營成本。
分享友人