點斜法 的英文怎麼說
中文拼音 [diǎnxiéfǎ]
點斜法
英文
point slope method-
The thesis has summarized the development of the oblique - pull bridge, its construction technology and the importance of bridge construction control, then has introduced project general situation, and has narrated detailed regulation, organization construction, the major work and difficult part of this bridge construction control. the following is the key part of this thesis, firstly, it has introduced the experiment work of early stage, structural calculation and its theoretical result : the absolute altitude of each operating mode, the absolute altitude of building mould in each section and the absolute altitude after pouring concrete ; then, it has discussed the method and content of the line shape control of the main beam, actual absolute altitude of building mould is put forward, and it has described the method of structural stress monitoring, how to arrange measure point and collect data, and how to analyze data. it has also narrated the method of rope force detection and structural temperature inspection
本論文在總結了斜拉橋的發展及其施工工藝，並指出了橋梁施工控制的重要性之後，簡要的介紹了工程概況，敘述了炳草崗金沙江大橋監控細則、組織機構及監控的主要工作和難點部分；論文的核心部分，在介紹了炳草崗金沙江大橋施工控制與監測工作的前期實驗工作和施工各工況標高、各節段支模標高、澆注混凝土后的標高的結構計算和其理論計算結果之後，詳細論述了主梁的標高線形控制方法和內容，實際支模標高的提出，結構應力監控的方法、布點、測讀及其對測讀數據的合理分析方法，索力檢測和結構溫度監測的方法。Perfect pre - processing and post - processing function is one of the main factors to evaluate the vitality and market value of the finite element analysis system surveying today development of finite element analysis technology, most of which concentrate on establishing fine user interface, also has some limitation on application, and especially, the research on the visualization of arbitrary cut - plane is always in ascendants to realize the visual processing on cut - plane needs reprocessing the results of finite element analysis which have get, so the algorithm is two parts : seeking the physical value of cut - plane and drawing 2d contours, the former, based on the theory of stress on " arbitrary inclined plane " in physical mechanics, use the method of linear interpolation method to get the coordination and physical value of intersection between cut - plane and element arris ; the latter, based on the tables on elements, nodes, stress and strain, summarize a rapid algorithm of generating 2d contours based on the grid. this thesis synthesizes there two parts and get a visual processing program under fortran
縱觀有限元分析技術的發展，目前大多集中在建立良好的用戶界面上的研究仍存在許多應用上的局限性，其中對任意剖面上可視化的研究仍處于方興未艾的階段。要實現任意剖面上可視化處理，必須先將得到的有限元計算結果進行再處理，因此在演算法上分為兩部分：求任意剖面上物理量值的演算法及二維等值線演算法。前一部分以彈性力學中「任意斜截面的應力」為理論基礎，利用線性插值方法得到截面與單元棱邊的交點坐標及交點物理量值；在此基礎上；根據已得到的單元及節點序號表、應力應變物理量表，總結出一種基於有限元剖分網格的快速生成二維等值線的演算法。Moreover, aiming at the location of inclined license plate, we have proposed the algorithm based on gray changing characteristic and orientation field. in this section, we discussed in detail the application of mathematical morphology operator in rough locating objective region and introduced the theory and realization method of orientation field. then we used it to detect inclined angel of objective region, finally we can precisely locate and emendate the inclined license plate based on detection result, and so we provided the favorable foundation for segmenting character
此外針對傾斜車牌區域的定位分割問題，提出了基於灰度變化特性和方向場計算的定位演算法，其中詳細討論了數學形態學運算元在目標區域粗定位中的應用，重點介紹了方向場計算理論和實現方法，並將其應用於目標區域傾斜角度的檢測，根據檢測得到的結果進行了傾斜車牌區域的準確定位和校正，為后續的字元分割打下良好的基礎。Interlocks the utilization different color the ceramic tile also is easy to do method, for instance all around brick uses the straight shop law, but among uses the diagonal line slanting shop the method, many kinds of specifications, many kinds of modelling encaustic brick has provided the display imagination space for you, becomes in the decoration a big luminescent spot
交錯運用不同顏色的瓷磚也是個好辦法，比如四周的磚採用直鋪法，而中間採用對角線斜鋪的方法，多種規格、多種造型的彩磚為你提供了發揮想象的空間，成為裝飾中的一大亮點。For rotor steel ( 30crlmolv steel ), the tests of low - cycle fatigue property are done under different temperatures. the fatigue life under different temperatures is researched to make up for the defects of the testing for foreign similar materials. when pull - stretch data is attempted to evaluate low - cycle fatigue data, the result shows that four - point associated method in middle - low life zone is done well under room temperature, but there are large errors of four - point associated method and general - slope method under other temperatures
在本文中，通過與國外同類材料的性能進行比較，國產材料與國外材料共有的材料特徵基本相同；對轉子鋼（ 30crlmolv鋼）進行了不同溫度下的低周疲勞性能實驗，研究其在不同溫度下疲勞壽命，以彌補國外對同類鋼材測試的不足；採用拉伸數據預測低周疲勞壽命時發現，室溫條件下用四點關聯法在中低壽命區預測較好，在高溫條件下四點關聯法和通用斜率法都有較大誤差，需要進行改進。Disigning coolant channel on the firebox of liquid rocket engine to loxodrome ( equal - angle helix ) groove can improve firebox coolant capability greatly. because the width dimension of loxodrome groove is narrow and the depth is deep, some machining methods are incapable, such as end - milling or electrochemistry. according to the peculiarities, a cnc disk - cutter - milling method which is composed of five motion axes with four simultaneously interpolated ones is researched. because most firebox generatrix is composed of complex curves, it is very difficult to get cnc cutting program with manual means. in order to deal with the problem, the loxodrome mathematics model is studied, and an auto - programming software system is developed. the software system can generate cnc cutting program of loxodrome on many kinds of turned surface. the constriction - distension segment of firebox is the most representative workpiece. the sharp changing of its generatrix slope makes loxodrome milling difficult. with the theory analyzing and practice cutting experiment, some applied techniques, which include milling mode and direction, choosing cutter diameter and cutting start point setting, are developed. adopting the technology above, tens regular workpiece have been manufacturing. the two - year manufacture practice has confirmed the validity and feasibility of developed loxodrome coolant channel milling method. the developed technology is also worth to be referenced to other similar workpiece
將液體火箭發動機燃燒室的冷卻通道設計為斜航線（等傾角螺旋線）槽形，可以大幅度改善燃燒室的冷卻性能.斜航線冷卻槽的槽寬尺寸較小而槽深尺寸較大，所以無法使用棒銑刀銑削、電化學等加工方式.針對這些特點，提出了五軸控制、四軸聯動的數控片銑刀銑削加工方法.由於燃燒室外表面的母線輪廓復雜，手工編制數控加工程序難度大.為了解決數控加工程序的編制問題，研究了斜航線的數學模型，開發了自動編程軟體系統.使用該系統，可以生成多種母線輪廓回轉體外表面上的斜航線數控加工程序.燃燒室收斂-擴張段的母線斜率變化大，加工難度大，是斜航線冷卻通道加工的最典型工件.經過理論分析和實際切削實驗，研究了針對該類型工件的片銑刀直徑選擇、銑削方式和方向、刀具調整和起刀點的設置等多項實際的加工方案.採用上述的一系列技術，已經成功地加工了數十個合格工件.經過兩年多的實際生產過程應用，驗證了所開發的斜航線冷卻通道加工方法的正確性和可行性.這些加工技術的研製成功，對其他相似類型零件的加工亦具有參考意義At sea, septentrional, by night the polestar, located at the point of intersection of the right line from beta to alpha in ursa major produced and divided externally at omega and the hypotenuse of the rightangled triangle formed by the line alpha omega so produced and the line alpha delta of ursa major
將大熊星座的「貝塔阿爾法」這一直線延長至星座外的「奧墨伽」 ，北極星便位於「阿爾法奧墨伽」這道外部區分線與大熊星座內的「阿爾法德爾塔」這一直線所形成的直角三角形斜邊的交點上340 。This thesis mainly discuss the practical value of the stereopsis test software in the ophthalmic clinical test of stereopsis, compare the difference between the traditional tno method and our software, measure the normal value of distant and near stereo acuity of health people. analyze the relation between the age and stereopsis, analyze the relation between the distance and stereopsis, test the near stereopsis development of young children with ophthalmic disease, test the influence on stereoacuity of the size of random dot
本課題主要探討自編立體視檢查軟體在眼科臨床立體視檢查中的應用價值；比較傳統的tno檢查法與本軟體檢查法的差異；測定正常人群各年齡組遠、近距離立體視銳度的正常值；分析年齡與立體視的關系；分析檢查距離與立體視的關系；測定斜視、弱視兒童的近距離立體視發育情況；測定隨機點大小對立體視銳度的影響。According to the moving characteristics of tracklayer, when the vehicle is on ramp and the ground ' s vertical pressure is linear, the calculating formulas of relationship between the deviation of the instantaneous steering center, the position of vehicle ' s gravity, steering radius, moving velocity, moving acceleration, and vehicle ' s orientation, were obtained by the theory and method of vector analysis in mathematics and mechanics
摘要根據履帶式車輛的運動特點，運用數力學中矢量分析理論和方法，推導了接地比壓為線性分佈時履帶式車輛在斜坡上轉向時，瞬時轉向中心偏移量與車輛重心位置、轉向半徑、行進速度、加速度、車輛方位相互關系的計算公式。The penstock for jinhe hydropower station is less in china, as it has a obliquity of 50 on the bending and inclined straight section in space ; for which the manufacture and installation are smoothly completed under the construction condition in the tunnel and the environment of alpine region with available construction method in combination of limited construction method for the key technical problems of the manufacture and installation of the penstock, which provides a reference for the constructions under the similar circumstance
摘要金河水電站壓力鋼管的空間轉彎和斜直段的50傾角在國內是比較少見的，針對鋼管製造、安裝的技術難點，在高寒和復雜的洞內施工環境中，結合有限的施工手段，採取有效可行的施工方法，順利完成了製造、安裝任務，對類似環境下的施工提供了一定的借鑒。The method is as follows : calculating the length, angles and coordinates of pre - cast hollow slab in cartesian coordinate system, and then adjusting the width of hollow slab beams and length of cantilever boards to make the linear cantilever slabs close to the transition of mute
具體方法是：採用直角坐標系計算預制空心板斜長、首尾夾角和起終點坐標，根據計算結果與路線線形之差，多次調整空心板梁的梁板寬度和懸臂長度，使外懸臂折線滿足路線的緩和曲線線形。The static analysis of the long span plate - truss composite cable - stayed bridges. first, the cr formation on the geometric non - linear structural analysis is introduced. next, the structural discretization of cable - stayed bridge, the stiffness matrix the formation of nodal force and the simulated construction system are introduced
首先介紹了本文採用的桿系結構幾何非線性問題的分析方法? cr列式法，其次介紹了板桁結合斜拉橋的結構離散及桿單元、梁單元的剛度矩陣以及節點力的形成方法，然後介紹了斜拉橋施工模擬體系的形成。Combining with the performances of danshan bridge, discussing the methods on the construction controlling and calculation of cable - stayed bridge, this paper raises an efficient construction controlling system, and realizes collecting construction data of the real bridge and technical information. by analyzing on the difference of theoretical calculation and real construction state, the author determines to take self - adapting construction controlling method which uses kalman filter method to identify and adjust construction parameters. by getting rational construction state from forward iteration method, this paper, taking concrete creep effect in consideration, raises a rational scheme to pre - remain deformation and adjust cable force
結合丹山橋的結構特點，通過對斜拉橋施工控制及結構計算方法的探討，提出了有效的施工控制系統，實現了對實橋施工數據和技術信息的採集；通過分析理論計算與實際施工狀態的差異，確定了以卡爾曼濾波法作為施工參數識別與調整的自適應施工控制方法；通過正裝迭代法確定其合理施工狀態，並考慮混凝土的徐變效應，提出了合理的預留拱度和索力調整方案。With the development of the network and the multi - processor system, the research, simulation and the impemeni of the system - level fault diagnosis which is the very important means to increase the reliability of the system, are becoming more and more important. on the system - leve1 fault diagnosis, based on the group theory of system - level fault diagnosis that has been put forward by pro f zhang, the paper constructs newly the theory bases, improves on the matrix method, reinforces and consummates group arithmetic of all kinds of test mode, for the first time, analyses and discusses the equation solution of all kinds of models, so al1 the consistent fault patterns ( cfp ) could be found, straightly and high efficiently, even if the sufficient and necessary condition of t - diagnosable is dissatisfied and the complexity of system - level fault diagnosis is greatly decreased, especialy in strong t - diagnosabl6 system. last the simulation system ' s function has been extended and the application hotspot and the development trend have been disscussed
本人在張大方教授等人提出的基於集團的系統級故障診斷的理論基礎上，重新構建了系統級故障診斷的理論基礎，定義了系統級故障診斷測試模型的三值表示；改進了系統級故障診斷的矩陣方法，重新定義了測試矩陣、鄰接矩陣、結點對、結點對的相連運算、極大準集團和斜加矩陣，由此能直觀、簡便地生成集團和極大獨立點集；補充和完善了各類測試模型的系統級故障診斷的集團演算法，通過定義集團測試邊和絕對故障集，簡化了集團診斷圖，由此能較易地找到所有的相容故障模式，即使不滿足t -可診斷性，大大減少了系統級故障診斷的復雜度，尤其是對強t -可診斷系統；首次分析探討了各類測試模型的方程解決，由此從另一角度能系統地、高效率地求出所有的相容故障模式（ cfp ） ：擴充了系統級故障診斷模擬系統的功能，快速、直觀和隨機地模擬實驗運行環境，進行清晰和正確的診斷，同時提供大量的實驗數據用於理論研究，優化演算法和設計。The blade inner channel cooling is a complex convection - conduction coupling problem. this thesis build a three - dimension. compressible turbulence model, and give a general solve method. with the geometrical model of the glossily rectangle straight channel, the rectangle straight channel with in - line arrays disturb plates, the rectangle straight channel with staggered arrays disturb plates, the rectangle straight channel with slant disturb plates, this thesis compute the flow and heat transfer condition when the cold air path though these channels, and gain the temperature field, pressure field, velocity filed, in addition. this thesis also analyze the influence of the different channel height, the different channel materials, the different channels, and gain the function relation between he nusselt number, friction factor and reynolds number. this thesis is emphasis on the new heat transfer enhancement structure, that is, disturb plates, with the comparison with the glossily channel and channel with pin fins, the heat transfer enhancement effect of the former is better, and the conclusion can be used in the design of aircraft blade
葉片內部通道冷卻是一個復雜的對流?導熱耦合傳熱問題，本文在分析葉片內部通道冷卻的流動與傳熱情況的基礎上，建立了三維、可壓縮紊流的物理模型，得到了通用的求解辦法；利用不帶擾流片的矩形直通道、帶順排擾流片矩形直通道、帶叉排擾流片、帶傾斜擾流片的矩形直通道的幾何模型，計算了冷卻空氣通過這幾種通道時的流動與換熱情況，得到了各種不同情況下計算區域的溫度場、壓力場、速度場；在此基礎上分析了不同的通道高度、不同的葉片通道材質對葉片內部通道冷卻的影響，並整理得到了各種通道形式下，努謝爾數和阻力因子與雷諾數的函數關系；本文重點研究了新型的葉片內部通道冷卻強化傳熱措施?帶擾流片的內部冷卻通道的強化傳熱效果，通過與光滑矩形直通道、帶針肋通道的冷卻效果的比較，表明了這種新型鮚構的優勢，對于葉片內部通道冷卻結構的設計可以起到指導的作用。When analyzing skew support continuous curved box girder bridge, curved grid girder analyzing method considering warping effect is applied. matrix displacement method is applied in analyzing skew support continuous curved thin - walled box girder bridge with restrained bearing. in order to convert original rigidity equations to structural rigidi ty equations that can be solved, bearing nodal displacement matrix can be introduced, then unknown quantities at the edge of beams can be consistent with the restrained directions of skew bearings, unit rigidity matrix and unit nodal forces can be gained. structural rigidity matrix can be composed according to matrix displacement method, so nodal displacements and inner forces on the end of the rod that are unknown can be gained calculating equations of inner forces on any cross - section can be solved
分析斜支承連續曲線箱梁橋時，採用考慮翹曲作用的曲線格子梁分析方法，應用矩陣位移法對具有約束支承形式的斜支承連續曲線薄壁箱梁橋進行分析，考慮到支座的約束條件並不與梁端彎曲角位移和扭轉角位移的方向一致，引入支座節點坐標矩陣，使得梁端的位移未知量與斜支座約束方向一致，來計算單元剛度矩陣和單元節點力，然後按照矩陣位移法組集總剛並建立結構剛度方程，根據結構剛度方程即可求解未知的節點位移及桿端力，推導出任意截面處的內力計算公式。Employing the oblique projection shifting method, we have solved some graphic problem in descriptive geometry. it is very simple and fruitful to deal with difficult problems in orthographic drawing
摘要介紹了投影變換中的斜投射法及其在解決工程圖學一些問題中的應用。用這種方法可解決工程圖學中用正投影方法不便解決的圖示、圖解問題，而且具有應用范圍廣、作圖簡便的優點。Rapid test procedure for thermal endurance of electrical insulating impregnating varnishes and varnished fabrics - thermogravameric point slope method
電氣絕緣浸漬漆和漆布快速熱老化試驗方法.熱重點斜法The discriminant condition avoiding the baroclinic destruction and the method to calculate the shearing resistance are given from the mechanics of shearing resistance and the type of shear failure
討論外節點的抗剪機理及節點的受剪破壞形式，提出了節點斜壓破壞的抗剪承載力計算方法。The artificial nerve network model for checking cable - stayed bridge is proposed on base of analyzing the structure characteristic, checking method, structure damage identification basic theory of cable - stayed bridge and the basic theory of artificial nerve network in detail, and the project example used by matlab language is given, and a satisfying network output outcome is obtained to show the influence and wide prospect of the application of the artificial nerve network in project
本文在詳細分析斜拉橋結構特點、斜拉橋檢測方法、結構損傷識別的基本理論及人工神經網路基本理論的基礎上提出了斜拉橋檢測的人工神經網路模型，用matalab語言，並通過工程實例中的檢測數據對網路訓練，取得了較滿意的網路輸出結果，顯示出人工神經網路在工程實際應用中的影響及廣闊的前景。分享友人