點蝕 的英文怎麼說
中文拼音 [diǎnshí]
點蝕
英文
corrosive pitting-
Tooth surface knocked burr or point corrosion on tooth surface or not in tangency
輪面磕碰,有毛刺或面發生點蝕或接觸不良The loca | n320gear oil used in gearbox of coal mill, the gears appeared pitting and scuffing, meanwhile shocking and noise increased, the oil oxidized and sludge formed
磨煤機齒輪箱使用n320齒輪油,造成齒輪點蝕,齒面嚴重磨損,振動及噪音增大,油質氧化,產生油泥。It was found that the pitting and crevice corrosion of steel wires were the main forms of corrosion
發現70鋼絲的縫隙腐蝕和點蝕是鋼絲繩的主要腐蝕形式。The result shows that under the effect of repeated impact load, the stress wave produces reflection in the metallurgical junction plane between coating and basal body, and forms stretch wave causing longitudinal split and angle split of coat ; the microcosmic spot pitting and deep layered peeling off occur in coating surface due to stress concentration ; the energy accumulation of impact loading causes rigidity variation and plastic deformation
結果表明:在多沖載荷作用下,應力波在塗層和基體的冶金接合面發生反射,形成拉伸波造成塗層的縱裂和角裂;在塗層表面由於應力集中,塗層表面發生微觀點蝕和深層剝落;沖擊載荷能量的積累,造成塗層試樣硬度變化和塑性變形。The prevention on surface spalling of supporting roller and its ring in rotary kiln
回轉窯輪帶與托輪表面點蝕剝落的防範Method of pitting potential measurement for stainless steels
不銹鋼點蝕電位測量的方法Standard practice for measuring intergranular attack or end grain pitting on metals caused by aircraft chemical processes
測量由於飛行器化學處理引起的對金屬的粒間沖擊或端面晶粒點蝕的標準實施規范Analysis and deal with gear ' s point corrosion of 4 m winder gearbox
絞車減速器齒輪點蝕問題的分析和處理Spectral correlation density analysis on bearing point defect diagnosis
譜相關密度分析在軸承點蝕故障診斷中的研究Effect of metallurgical factors on pitting propagation process of low alloy steels
冶金因素對低合金鋼點蝕擴展過程的影響Implants for surgery - measuring method for pitting corrosion potential on stainless products
外科植入物不銹鋼產品點蝕電位Study on the pitting corrosion resistance of butt resistance welds of stainless steels
不銹鋼電阻對焊接頭的抗點蝕性能研究Calculation of load capacity cylindrical gears ; calculation of pitting resistance
圓柱齒輪承載能力的計算.耐點蝕性能的計算Air bubble pitting
氣泡點蝕The bp neural network is applied to the recognition of wear particles, and a bp neural network sorting system expected to recognize severe wear particle, cutting wear particle, normal wear particle and fatigue wear particle is designed and trained. 6. the function of the neural network ' s hidden layer is analyzed
將神經網路應用於磨粒識別,設計磨粒分類器,在網路學習中運用改進的bp模型,識別嚴重滑動磨損磨粒、切削磨粒、正常磨損磨粒和疲勞點蝕磨粒,隨機選取50個樣本對分類器進行訓練。Using extremum statistical method to predict pit corrosion sizes of the pipeline in service and further to evaluate the residual strength of the pipeline has a great significance for controlling accidents of corrosive perforations, guiding pipeline rehabilitation and replacement as well as prolonging service life of pipeline
長輸管道的腐蝕類型多為均勻腐蝕或點腐蝕,採用極值統計方法對在役管道的點蝕尺寸進行預測,進而評價管道的剩餘強度,對于控制管道的腐蝕穿孔事故、指導管道的修復更換、延長管道的使用壽命具有重要意義。This paper discusses the statistical rule of maximum corrosive pit depth and determination method of extremum estimation for local corrosion depth, and presents a practical example of calculation
文章討論了管道最深點蝕孔深度的統計規律以及局部腐蝕深度最大極值估計值的確定方法,並給出了實際算例。It is not like expert system, which needs repeat three periods - conceptualization, formalization and improvement. in this paper, research the fault gears " three models by the vibration signal. pick up the character vector by using the wavelet packet and energy method as the ann input neural vector
本文以齒輪箱為研究對象,在齒輪正常、齒根裂紋、齒面非正常點蝕三種模式下,對振動信號加以分析,運用「小波包?能量」法提取出信號特徵量,作為神經網路的輸入向量,採用包括有輸入層、單隱層和輸出層的bp網路。It was shown that na2co3 inhibited the pitting corrosion of aluminum alloy to some extent
實驗結果表明,碳酸鈉對鋁合金具有較好的緩蝕作用,在一定程度上抑制了鋁合金的點蝕。Corrosion of metals and alloys - determination of the critical pitting temperature under potentiostatic control
金屬和合金的腐蝕性.靜電位控制下的臨界點蝕溫度測定分享友人