齒后角 的英文怎麼說
中文拼音 [chǐhòujiǎo]
齒后角
英文
angle of back of tooth-
Equations of mesh, shorting contact line, undercutting limit line, meshing limit lines and the existence conditions, angle between the direction of relative speed and the direction of contact line, induced normal curvature about every point on the contact line are established. moreover, the paper also theoretically analyzed the error of the grinded gear surface. on the basis of the theory, the computer program is worked out to automatically produce the contact line and the boundary curves of mesh. analysis of meshing circs under different parameters can be done so that we can gain the best process condition
首先對漸開面二次包絡理論進行了深入的探討，推導出了兩次嚙合的嚙合方程式、瞬時接觸線方程式、根切界限線方程式、嚙合界限線的方程式及其存在條件，相對運動速度方向與接觸線方向的夾角及接觸線上各點的誘導法曲率；此外，還對磨齒后工件的齒面誤差進行了理論分析；並在理論基礎上編制了相應的計算機程序，自動生成接觸線族及嚙合界限線，對不同參數條件下的嚙合情況進行分析，可以使工藝條件達到最佳狀態；最後研究了磨齒裝置，設計了磨齒機的傳動系統。Through the simulation of the forming process, we can get the deformations, stress, strain, plastic flowing in sheets and the interface state under impact load and rolling load, the deformation of the sawtooth form and comparing to the initial state, the results above are expressed in computer animated way. and the effect of geometrical ( mainly different form, including 90 degree, isoceles triangle ， 75 degree, and 1. 5 high and wide ), material and technical parameters on the bond strength are analyzed, also including the comparison of different sawtooth form. the optimum parameters are got
對雙金屬復合板成型過程進行模擬，從而得到在沖擊載荷和軋輥壓力作用下基板和覆板的應力、應變分佈和塑性流動變形規律，復合后的齒形的變形情況與初始齒形形成對比，以動畫的方式模擬成型過程，並分析了不同幾何參數（主要是不同的齒型，其中包括直角齒型、等腰齒型、 75度齒型、 1 . 5高寬齒型） 、材料參數、工藝參數對復合強度的影響，以及不同齒型的變形對比以及齒型對復合情況的影響，提出最優齒型、最優工藝參數，有效地指導了實驗。Dental porcelain nickel and cobalt alloy, known as porcelain alloy, i currently producing ceramic alloy shape of a flat circular, hexagonal cylindrical and are mainly used for dental patients with tooth loss or defect repair, with a solid combination of ceramic powder characteristics, vivid natural teeth restored to mouth bring resume cavity in patients with teeth chewing function and beauty aesthetic good results
牙科用鎳鈷烤瓷合金，簡稱為烤瓷合金，我公司目前生產的烤瓷合金外形有扁圓形、六角形和圓柱形三種，主要用於牙病患者牙齒的缺失或者缺損的修復，具有與瓷粉牢固結合的特點，修復后牙齒逼真自然，給口腔牙齒患者帶來恢復咀嚼的功能和美容美觀的良好效果。This paper introduces the characteristic of these two types of driving mode, compares them from aspects of mounting, operation and maintenance, then comes to the conclusion that the belt motion will lead the development of automatic door
介紹了齒帶和螺桿兩種門傳動方式的特點，並從安裝、使用和維護的角度進行分析比較后認為，齒帶傳動是發展趨勢。Finally, by means of comparing the theoretical tooth surface equation with the tooth surface equation included errors of cutter position and cutter position angle, the quantitative analysis of the theoretical tooth shape and the tooth shape considering the errors of cutter position and cutter position angle was curried out based on the software above. from which, the effect of errors of cutter position as well as cutter position angle on the processed tooth shape and transmitting behavior of this kind of gearing was studied
最後，通過比較雙圓弧弧齒錐齒輪齒面理論方程與加入刀位及刀位角誤差后的齒面方程，應用上述軟體和通過進一步的數值計算，進行了無誤差的理論齒形與加入刀位及刀位角誤差后所得到的實際齒形之間的定量分析，比較直觀、方便、準確地對刀位及刀位角誤差對雙圓弧弧齒錐齒輪的齒形以及傳動的影響進行了初步研究。This is achieved by utilising a torque transfer differential which is controlled by various sensors and an electronic control unit ( ecu ) to enable a difference in torque to go to each of the rear wheels
感應器根據收集到的轉向角度，油門大小，車輪轉速，前後，側向加速力等信息經過計算后，電腦控制油壓系統介入，推動差速器里的離合裝置，把驅動力誘導到一組減速齒輪，從而改變左右輪驅動力。For cutting the composite lock gear with unequal tooth thickness, a study is made on the design method of gear sharper cutter with nonstandard parameter involute tooth profile and noninvolute tooth profile. the cutter tooth arrangement, the choice of teeth number of the cutter and the basic method of cutter design are discussed ; and a new method of choosing deflection factor by using limited area is presented. and the curve of relationship between rear angle on tooth crest and helical angle on tooth side of the cutter is given so as to give a basis for the gear sharper cutter to choose its parameters. to design nonstandard gear sharper cutter by adopting the method mentioned above will simplify the calculation and will increase the efficiency of design
研究加工不等齒厚的非標準參數漸開線齒形，與非漸開線齒形復合的鎖閉齒輪插齒刀刀齒的排列、刀具齒數的選擇以及刀具設計的基本方法，介紹用限制區域選擇插齒刀變位系數的新方法，並給出刀具齒頂后角與側螺旋角的關系曲線，為插齒刀參數的選擇提供依據.結果表明，採用上述方法設計非標準復合齒輪插齒刀，可簡化計算和提高設計效率Initially the thesis compares the old management mode with concurrent management mode, then puts forward concurrent shop floor work flow and gives several implement strategies which support concurrent engineering ( ce ). secondarily, some theories of stock management which are related to tool management are discussed, and these theories are taken into consideration when constructing the management models of tools in stock. at last, the thesis details the consequent software development work of the tool management system
首先，本文對車間原有的管理方式與實施并行工程后的管理方式進行了分析比較，提出了支持并行工程的車間工作流程，並且從支持并行工程的角度，對工具的管理提出了一些實施策略；其次，分析討論了與工具庫存有關的一些控制系統和方法，並探討了如何在工具庫存管理中運用這些理論；最後，結合開發江齒工具管理系統的實踐，詳細介紹了工具管理系統的開發過程。分享友人