齒根圓柱 的英文怎麼說
中文拼音 [chǐgēnyuánzhù]
齒根圓柱
英文
root cylinder-
The undercut controlling of involut cylinder gear shaving
漸開線圓柱齒輪剃齒過程中的根切控制As both the meshing point and ball ' s center are on the given cylinder, a general method for developing the cam ' s profile is studied. it is proved that the profile of positive and negative transmission is unique if the face gear, the difference between face tooth number and ball number and the diameter of ball are the same. the concrete expression of meshing cam on given spatial cycloid profile, and the characteristics of the profiles are discussed
論文的主要工作包括： 1 、根據嚙合點和鋼球中心軌跡均在同一圓柱面上的特點，研究了給定端齒齒廓條件下求解凸輪齒廓的一般方法；論證了在給定端齒、齒差數和鋼球直徑相同的條件下，正負齒差嚙合齒廓的唯一性；討論了端齒為球面擺線時，凸輪齒廓的具體表達式，並研究了該齒廓的性質。Abstract : in this paper, the kinematically admissible velocity fields are established by using the metal flow patterns based on the experiments, and the configuration dimensions of billet and the curves of load - stroke in precision forging process for spur gear from solid billet are simulated on computer by upper bound method. the results acquired in the simulation are in good agreement with those obtained in the experiments
文摘:本文利用有實驗根據的變形流動模式建立動可容速度場，利用上限法模擬用實心坯料精鍛直齒圓柱齒輪時坯料的外形尺寸變化和力?行程曲線，所得結果與實驗測定值很一致，可供沖擠精鍛工藝設計參考。Tooth surface equations and contact line equations of the involute worm gearing are established according to its machining methodology. meshing characteristics in rigidity condition are studied. these characters include the inductive normal curvature along the contact line on the worm surface, the first and the second limit lines during the engage of the worm gear, and the influence of the intersect angle between the contact line the relative velocity of the worm and the gear on transmission performance
根據漸開線圓柱蝸桿傳動的創成方法，建立了漸開線圓柱蝸桿和蝸輪的接觸線方程式、齒面方程式，分析了漸開線圓柱蝸桿傳動的剛性嚙合特性，如蝸桿與蝸輪嚙合時的誘導法曲率、一類界限曲線、二類界限曲線和蝸桿與蝸輪間相對速度方向和接觸線方向的夾角對傳動性能的影響； 2Cylindrical gears - iso system of accuracy - part 1 : definitions and allowable values of deviations relevant to corresponding flanks of gear teeth
圓柱齒輪. iso精度體系.第1部分:齒輪嚙合對應齒根面的相應偏差定義和容許值Cylindrical gears. iso system of accuracy. part 1 : definitions and allowable values of deviations relevant to corresponding flanks of gear teeth
圓柱齒輪. iso準確度體系.第1部分:與齒輪齒對應齒根面有關的偏差的容許值和定義Abstract : this paper derives thecalculating formulas to the contact strength and oil - film thickness of the involute spur gear according to hydrodynamic lubrication principle. through check with test, shows that they may rully replace now available hertz formula and dowsonformula respectively
文摘:根據流體動力潤滑原理，推導出了漸開線直齒圓柱齒輪接觸強度及油膜厚度的計算公式，通過實驗驗證，說明它們可以完全分別代替現有的赫芝公式及通森公式。分享友人